Tridonic 28003540 G2 Basic DIM Wireless Instruction Manual
- June 15, 2024
- TRIDONIC
Table of Contents
Tridonic 28003540 G2 Basic DIM Wireless Instruction Manual
INSTALLATION
Wiring diagram DALI
* Max. wiring length 5 m with integrated DALI power supply and a cross
section of 1 mm².
Antenna is located on the top of the device.
The basic Dim Wireless G2 is a Bluetooth DALI controller with a freely configurable push-button input and has an integrated DALI power supply. Therefore no external DALI supply is needed.
Technical Data
Rated supply voltage : 220 – 240 V
Mains frequency: 50 / 60 Hz
Max. mains current: 10 mA
Typ. power input on stand-by: < 0.4 W
Input: 1 push-button
Max. cable length push button: 5 m at 0.14-0.5 mm²
Radio transceiver operating frequencies: 2.4 – 2.483 GHz
Max. output power radio transceiver: + 4 dBM
Output: DALI (compatible)
Number of DALI addresses : 4
Guaranteed output current,: DALI 2 10 mA
Max. output current, DALI: 250 mA
Max. DALI wiring length: 5 m at 1 mm²
Operating temperature: -20 … +70 °C
tc point: 80 °C
Storage temperature: -25 … +75 °C
Dimensions LxWxH3: 80.7 x 30 x 15.3 mm
Type of protection: IP20
- Assignment of max. 4 single / group addresses, depending on the device profile.
- Max. 5 loads.
- Screw fixings can be removed.
Safety instructions
- Installation of this device may only be carried out by specialist staff who have provided proof of their skills.
- Switch off the mains supply before handling the device.
- Observe the relevant safety and accident prevention regulations.
Installation Instructions
Make sure that the mains voltage is switched off when making any connections.
Use 0.2 – 1.5 mm² solid or stranded electrical wires for the mains supply /
DALI
terminals and 0.14 – 0.5 mm² for the push-button terminals.
Strip the wire 8.5 – 9.5 mm from the end.
Make sure to connect the input and outputs correctly. Mains input connector is
marked with letters L and N.
Compatible devices
Compatible with all Android 4.4 (Kit Kat) or later, iPhone 4S (iOS 5.0) or later and iPAD 3 (iOS 5.1) or later.
Hereby, Tridonic declares that the radio equipment type basic DIM Wireless G2
(28003540) is in compliance with Directive 2014/53/EU.
The full text is available at the following internet address:
http://www.tridonic.com/TA120
Areas of application
The device may only
- be used for the applications specified.
- for safe installation in dry, clean environment.
- be installed in such a way that access is only possible using a tool.
Safety Information
General Safety Information
- Installation, commissioning and maintenance only by quality electrician.
- Never perform any work on the luminary with voltage applied. Danger to life due to electric shock!
- Electric connection must be appropriate according to all applicable standards and other national and international safety and accident prevention regulations.
- Damaged luminaries must not be operated.
- Observe and retain safety instructions and mounting instructions
- No liability is accepted for damages resulting from improper use.
- Use genuine parts only for repair.
- Ensure stability of the ceiling and fastening elements.
- The luminaire is exclusively intended for interior rooms and ambient temperatures not exceeding 25°C, unless otherwise described by labeling the luminaire.
Operation of the luminaire
- Abnormal dark spots may be an indication of partial failure of LED. Inspect regularly and replace the luminaries affected. The light source (LED) of this luminary must not be exchanged or replaced by the user.
- Exceeding the permissible ambient temperature will reduce the luminary’s life cycle, resulting in premature failure in extreme cases.
- Avoid condensation of the luminaire.
- Any mechanical load to the LED circuit boards is not permitted.
- LED s can be damaged by electrostatic discharge (ESD). This may result in total failure. Always avoid direct contact.
- Depending on their concentration, chemicals can corrode the LED modules and lead to reduction of luminous drift of luminous color and/or total failure. Always avoid direct contact with acids, bases, solvents, volatile organic compounds and/or oils. Ensure sufficient ventilation to prevent damage by gas release.
- Avoid EDS problems by not routing feed-through wiring directly along the wiring of the luminary.
- Connect control inputs of dilemma luminaries with standard cables suitable for power supply voltage.
Changes to our products
Medication, reworking, re-marking of products can have a negative impact on
their technical properties, destroy them and possibly cause consequential
damage to other objects. The manufacturer cannot be held responsible for
damage caused by such changes.
d+ IP5x – dust non conductive
d+ IP6x – dust conductive and dust non conductive
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>