VOLLRATH 55000 Redco Instacut 5.0 Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH 55000 Redco Instacut 5.0
Specifications
- Model: InstacutTM 5.0
- Functions: Slicing, dicing, wedging, coring
- Intended Use: Soft vegetables and fruits
- Not Intended for: Hard root vegetables like carrots and sweet
potatoes
Product Usage Instructions
Features and Controls
The InstaCutTM 5.0 manual food processor includes the following components:
- Base Assembly: Holds guide rods and blade assembly.
- Bumpers: Cushions the pusher head during operation.
- Guide Rods: Guides and aligns the pusher head onto the blade set.
- Thumbscrew: Secures pusher head block and blade assembly.
- Bushings: Ensures smooth operation of pusher head on guide rods.
- Handle: Raises and lowers the pusher head.
- Pusher Head Assembly: Includes bushings, pusher head, and pusher block.
- Pusher Head Block: Pushes food through the blade assembly.
- Blade Assembly: Houses the blades.
Operation
- Inspect Equipment: Ensure cleanliness and blade condition before each use. Replace loose or broken blades.
- Setup: Place the equipment on a clean, flat surface.
- Bumper Check: Verify bumpers are in place on guide rods to prevent equipment damage.
- Blade Alignment: Ensure proper blade alignment by setting the pusher head slowly.
Cleaning
To clean the equipment:
- Warning: Blades are sharp. Handle with caution.
- Remove Blade Assembly: Loosen the thumbscrew and carefully remove the blade assembly for cleaning.
Thank you for purchasing this Vollrath equipment. Before operating the equipment, read and familiarize yourself with the following operating and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Save the original box and packaging. Use this packaging to ship the equipment if repairs are needed.
SAFETY PRECAUTIONS
To ensure safe operation, read the following statements and understand their meaning. This manual contains safety precautions which are explained below. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that will or can cause
severe personal injury or death.
CAUTION
Caution is used to indicate the presence of a hazard that will or can cause
minor or major personal injury if the caution is ignored.
NOTICE: Notice is used to note information that is important but not
hazard-related.
To reduce risk of injury or damage to the equipment:
- Check equipment before each use to insure it is clean.
- Check for broken, nicked or dull blades and if found, replace the blade assembly.
- Check to insure that the pusher head sits down completely on the rubber bumpers.
- On tabletop models the suction cups will hold the equipment securely to smooth surfaces.
- Guide rods must be lubricated using a light coating of mineral oil, Petrol-Gel, or food grade lubricant. DO NOT USE COOKING OIL AS IT WILL BECOME STICKY AND MAY PERMANENTLY DAMAGE
THE PUSHER HEAD BEARINGS.
FUNCTION AND PURPOSE
The InstaCut™ 5.0 manual food processor is intended for slicing, dicing, wedging and coring soft vegetables and fruits. It not intended to cut hard root vegetables such as carrots and sweet potatoes.
OPERATION
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle
with caution.
-
Before each use, check that the equipment is clean and the blades are in good condition. If loose or broken blades are found, replace the blade assembly.
-
Place the equipment on a clean, flat work surface.
-
Verify the bumpers are in place on the guide rods. DO NOT USE EQUIPMENT IF BUMPERS ARE NOT IN PLACE.
NOTICE: Using this equipment without the bumpers in place may damage the equipment. -
Check for proper blade alignment by slowly setting the pusher head onto the blade assembly. They should slide together with no obstructions. If there are obstructions, verify they are a matching set. Remove the obstruction.
-
Verify that the blade assembly and pusher block are the desired size.
-
Prepare the food product to be processed. For slicing and dicing the maximum size of the food product is 5″ (12.7 cm). For wedging and coring the maximum size of the food product is 3½” (8.9 cm) in diameter.
-
Lift the handle and place the food product on the blade assembly with the flat side down.
-
Remove hand from the blade assembly area and place that hand on the leg of the base.
-
Using a strong, quick, downward thrust, force the food product through the blade assembly.
-
Repeat this process until you have prepared enough food product for your daily needs.
-
Clean and lubricate your equipment immediately after each use. See the Cleaning section of this manual for more information.
CLEANING
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle
with caution.
NOTICE: Food acids will dull the blades and corrode the metal.
Always clean this food preparation equipment immediately after every use.
NOTICE : Do not put this equipment in a dishwasher or dish machine with soaps, detergents, or other alkaline chemicals that can harm the equipment.Handwash only.
NOTICE: Do not use abrasive materials, scratching cleansers or scouring pads to clean this equipment. These can damage the finish.
Disassemble
- Slide the pusher head assembly up and off of the guide rods.
- Remove the two thumbscrews and separate the pusher block from the pusher head.
- Raise the bumpers approximately 2″ (5.0 cm).
- Loosen the thumbscrew and carefully remove the blade assembly.
Wash
-
Wipe, rinse or spray off equipment, pusher head and blade assembly thoroughly with HOT water.
-
Do not wipe across the blades.
NOTICE: Wiping across the sharp edge of the blade can cause injury and will dull the blades. -
Clean the blade assembly by forcing water under pressure, through the blades from the unsharpened side. If necessary, use a nylon bristle cleaning brush to push food particles out from the unsharpened side of the blade assembly.
-
Let the equipment air dry.
Reassemble
-
Install the cutting blade assembly into the base. Tighten the thumbscrew to push blade securely against the other side.
-
Lubricate the guide bar with mineral oil or Petro-Gel.
NOTICE: Do not use cooking oil as it will become sticky and may permanently damage the equipment. -
Slide the bumpers into place.
-
Reassemble the pusher head assembly.
PREVENTATIVE MAINTENANCE
- Clean the equipment after every use.
- Use for intended purposes only.
- Change the blades regularly – based on usage.
REPLACE THE BLADE ASSEMBLY
WARNING
Sharp Blade Hazard
Blades are sharp and can cause cuts. To avoid injury from sharp blades, handle
with caution.
Wash new blades with warm, soapy water and rinse thoroughly to remove the thin protective oil film. Keep the sharp edge away from you when handling blades.
- Familiarize yourself with the parts diagram for your equipment.
- Remove the pusher head assembly by sliding the pusher head off the guide rods.
- Raise the bumpers approximately 2″ (5.0 cm).
- Loosen the thumbscrew and carefully remove the blade assembly. Remove the cutting blade assembly by pressing upwards on the bottom of the side of the blade holder, where the thumbscrew is located. Discard the old blade assembly.
- Install the new cutting blade assembly by inserting the tab on the blade holder into the groove in the base, then lowering the blade holder into the seated and flush position in the base. Tighten the thumbscrew.
- Slide bumpers down guide rods to contact base. Position pusher head assembly onto the guide rods, slowly lower pusher head assembly, and check pusher head block to blade alignment.
- Lubricate the guide rod with mineral oil or Petro-Gel after each use. Do not use cooking oil as it will become sticky and may permanently damage the equipment.
TROUBLESHOOTING
Problem| Might be Caused By| Course of
Action
---|---|---
Broken Blade| Blades were dull.| Replace the blade assembly. Also inspect the
pusher block. Replace if damaged.
Pusher head does not slide easily.| Guide rods improperly or insufficiently
lubricated.| Clean and lubricate the guide rides. See Cleaning.
Cuts poorly.| Blades are dull.| Replace blade assembly.
Cannot push food through.| Blades are misaligned or incorrect pusher block is
installed.| Confirm the pusher block is correct for the blade assembly and
that there is no interference between the pusher block and blade assembly.
SERVICE AND REPAIR
Serviceable parts are available on Vollrath.com.
To avoid serious injury or damage, never attempt to repair the unit or replace
a damaged power cord yourself. Do not send units directly to The Vollrath
Company LLC. Please contact Vollrath Technical Services for instructions.
When contacting Vollrath Technical Services, please be ready with the item
number, model number (if applicable), serial number, and proof of purchase
showing the date the unit was purchased.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
This warranty does not apply to products purchased for personal, family or
household use, and The Vollrath Company LLC does not offer a written warranty
to purchasers for such uses.
The Vollrath Company LLC warrants the products it manufactures or distributes
against defects in materials and workmanship as specifically described in our
full warranty statement. In all cases, the warranty runs from the date of the
end user’s original purchase date found on the receipt. Any damages from
improper use, abuse, modification or damage resulting from improper packaging
during return shipment for warranty repair will not be covered under warranty.
For complete warranty information, product registration and new product
announcement, visit www.vollrath.com.
Technical Services
The Vollrath Company, L.L.C. Headquarters 1236 North 18th Street Sheboygan,
Wisconsin 53081-3201 USA
Main Tel: 800-624-2051 or
920-457-4851 Main Fax:
800-752-5620 or
920-459-6573 Canada Customer Service:
800-695-8560 Tech Services:
techservicereps@vollrathco.com
www.vollrath.com
Pujadas
Ctra. de Castanyet, 132 P.O. Box 121 17430 Santa Coloma de Farners (Girona) –
Spain
Tel. +34 972 84 32 01
info@pujadas.es
Vollrath of China Vollrath Shanghai Trading Limited
Room 201, Building A Xin Yi Plaza
1618 Yi Shan Road Shanghai, 201103 China, P.R.C.
Tel: +86-21-5058-9580
Vollrath de Mexico S. de R.L. de C.V. Periferico Sur No. 7980 Edificio 4-E Col. Santa Maria Tequepexpan 45600 Tlaquepaque, Jalisco |MexicoTel: (52) 333-133-6767 Tel: (52) 333-133-6769 Fax: (52) 333-133-6768
FAQ
Q: Can I use hard root vegetables with the InstaCutTM 5.0?
A: No, the InstaCutTM 5.0 is not intended for hard root vegetables like carrots and sweet potatoes. It is designed for soft vegetables and fruits.
Q: What should I do if I find loose or broken blades?
A: If loose or broken blades are found, replace the entire blade assembly before further use to ensure safe operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>