TRIDONIC 28002680 Lighting Controls and Connectivity sceneCOM Installation Guide

: June 8, 2024
: TRIDONIC

Table of Contents

DIMENSION
Topology A
Topology B
Installation types
Application area
Technical data
System design and installation notes
Function key
Test key
Status LED
Safety instructions
Installation
Initial steps after installation
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TRIDONIC 28002680 Lighting Controls and Connectivity sceneCOM

DIMENSION

Topology A

Topology B

Installation types

Application area

Control device with 3 DALI-compliant outputs for controlling a maximum of 192 luminaires

Technical data

Nominal Voltage	110-240 V.50-60 Hz
Permissible input voltage	100-260 V. 50-60Hz
Power dissipation	Max.20W
Outputs	3 DALI-compliant outputs (DALI BUS 1 – 3); per output: max. 64 DALI

addresses;
Ports| 1 Ethernet port (Ethernet). RJ45 plug: speed of data transfer.10/100Mbif/s
Interface| Service Interface
Terminals| 05 – 25 mm’ (solid or fine-stranded)
Degree of protection| IP20
Protection class| Pro1ect1on class II (only with correctly installed terminal covering)
Housing materials| Polycarbonate (PC),!lame-retardant, halogen-free
Installation| On top-hat rail35mm,naccordance with EN50022
Dimensions| 160 x 91 x 62 CW x H x D. in mm),9 HP every 17.8 mm
Permissible ambient temperature| 0–50°C, installation type 1 (e.g. in distribution board)
0–40°C, installation types 2 and 3
Permissible relative humidity| 20–90%, non-condensing
Weight| Approx. 600 a

System design and installation notes

Installation: fixed only, in a clean and dry environment, access only possible with tools; in solid distribution board or solid, closed distribution unit only, requirements given in standards for fire and contact safety must be met
Topology: connect scene COM L and display device (touch panel, computer) via Ethernet cable (topology A) or connect scene COM L and display device (touch panel, computer, mobile device) via a wireless access point (topology B)
Mains line: must not be interrupted by control points
Ethernet line: at least CAT5 cable, shielded
Bus line and DALI control line: use standard installation materials for low-voltage systems (< 1,000 V); only tree, linear and star topologies permitted
Bus cores: may be reverse connected
DALI control line:

Conductor cross-section	Maximum DALI line length
2 x 0,50 mm²	100 m
2 x 0,75 mm²	150 m
2 x 1,50 mm²	300 m

Function key

The function key can be Used to trigger certain function.

Triggering a function

press the function key
Release the function key in the desired orange phase
Function is triggered.

Orange phases (status LED device)

Orange phase	Function
1	Restart the sceneCOM L.
2	Delete the addresses and short addresses of all control gear and input

devices connected to the 3 DALI control lines.
3| Reset the IP address to the factory setting (10.10.40.254).

Test key

The test key can be used to trigger tests and certain functions for the related output (DALI BUS 1 – 3).

Triggering a function

press the test key
Release the test key in the desired orange phase.
Functions is triggered

Orange phases (status LED DALI BUS 1-3

Orange phase	Function
1	Exit test mode for all outputs.
2	Delete the addresses and short addresses of all control gear and input

devices connected to the corresponding DALI control line.

Test mode

If the test key is pressed for less than 2 seconds, all connected luminaires are switched on.
If the test key is then pressed again for less than 2 seconds, the luminaires alternate each time between on and off.
To exit test mode, press the test key and release during the 1st orange phase

Status LED

Device

Status LED	Duration	Description
Green, intermittently flickering	Continuous	Fault-free operation
Off	Continuous	No mains voltage (L, N)

Safety instructions

The device may only be used for the application area specified.
Relevant health and safety regulations must be observed.
When mounting and installing the device, the voltage supply must be disconnected.
Only qualified personnel may mount, install and commission the device.
Protection class II can only be guaranteed when the terminal covering has been correctly installed.
If a fault occurs, dangerous voltage levels may be present at the DALI terminals and on the DALI control line.

Installation

Disconnect the voltage supply.
Press the black locking hook down

Installation type 1 (e.g. in distribution board)

First attach the top part and then the bottom part of the device to the top-hat rail

Installation type 2

First attach the top part and then the bottom part of the device to the top-hat rail.

Installation type 3

Depending on which side the black locking hook is situated:

First attach the left part and then the right part of the device to the top-hat rail.
— or —
First attach the right part and then the left part of the device to the top-hat rail
Fasten the locking hook again.
Reconnect the voltage supply

Initial steps after installation

Requirement:

The scene COM L control device and display device (touch panel. computer) have been connected in accordance with topology A.
-or-
The sceneCOM L control device and display device (touch panel. computer. mobile device) have been connected in accordance with topology B.

Ensure that the following settings are stored for the display device and the wireless access point:
– IP address . . ….. …….. 10.10.40.2 – 10.10.40.253
– Subnet mask. ………. . .. 255.255.0.0
Open a browser (Google Chrome recommended).
Go to the IP address of the sceneCOM L (10.10.40.254).
-+ The Tridonic system web application is displayed.
Run the installation test (see Test key – Test mode).
Correct the installation faults.
Commission the Tridonic system.
Note: Detailed information on commissioning and configuration can be found in the commissioning instructions.