secrui M5373+F152 Wireless Doorbell User Manual

secrui M5373+F152 Wireless Doorbell

Safety

• A Before proceeding with the installation, please note the following safety warnings:
• Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

What You Should Know Before Installation

• Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
• Set a desired music (different or same one) for transmitters before installation. Doorbells have been paired and set to a default chime (Ding Dong) before leaving factory.
• Please do not install transmitter on metal doors since it is hard for the signal to transmit.
• Please take out the battery insulating strip before using if have. (As picture 1)
  Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect them adhesion over a longer period of time.

Product Structure Diagram

1. LED Light

2. Music Control

3. Volume Control

4. Plug

5. Speaker

6. Led Indicator

7. Push Button

Set up and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell will light up and ring. If it does not, see “Connect a Push Button” on page 5.

Adjust the Volume

• Press the to adjust the volume. (when the power is cut off, and power is restored again, the volume will be automatically adjusted to maximum)
• At the maximum and minimum volume, the door bell will sound “didi” twice
• There are total 5 levels including the mute mode.

Change the Tune
Press the to loop tones.

Connect a Push Button
You can connect up to 20 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.

1. VARIABLE- Tone Pairing

   • Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beep once, which means the receiver get into pairing mode.

   • Long Press 5s

   • Press push button, the receiver will beep twice with LED indicator flashes 1s.

   • Press push button again, the receiver will beep once with LED indicator flashes 1s, which means the pairing= is successful.
     Notice:

   • Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.

   • Adding the additional push buttons or receivers please according to the above steps.

2. Fixed- Tone Pairing (Only play your saved tone)

   • Select a tone that you like
   • Pressing and holding button together for about 5s until the receiver beeps once, which means the receiver get into pairing mode.
   • Press push button once, the receiver will beep twice with LED indicator flashes 1s.
   • Press push button once again, the receiver will beep once with LED indicator flashes 1s, which means the pairing is successful.
     Notice:
   1. Short press or leave it 20s without any operation, the doorbell will exit the pairing mode.
   2. Pair and set only one transmitter at a time to avoid interference and ensure successful operation.

Delete a Push Button

• Plug-in the receiver, pressing and holding the on the receiver for 5s, the receiver will beeps once, which means the receiver get into pairing mode.
• Long Press 5s
• Pressing and holding the again for 5s, the receiver beep 4 times, LED flashes 4 times, which means that the pairing of all buttons is deleted.

Reset (Clearing out Settings)

• To clear out all setting, hold down and plug it into an outlet. After playing the beep 10 times slowly and beep 6 times fast, all settings will return to factory defaults.
• Hold down and Plug in

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.

1. For Receiver: Plug-in receiver: Just plug receiver into standard outlet in room.

2. For Push Button:
   IMPORTANT:

   • Before installation, please test if the operating range you choose is working and set music if needed.
   • Before you drill any hole in the wall, please make sure there are not cables or pipes.
   • To install you will require a drill and cross-head-ed screwdriver.

• Open the Transmitter with screw driver and separate the front cover from the back cover. Penetrate the two standby holes at the back cover with two screws. Then fix the screws on the wall at suitable height.
• Or you can stick the Transmitter with the double-sided adhesive tape.
• If you are not mounting the push button to the wall, place it where you want it.

Battery Replacement of Push Button

Open the battery cover and install the CR2032 battery

SPECIFICATION

TROUBLESHOOTING

1 Year Limited Warranty

• This product is warranted to the original purchaser only for a period of 1 year from the date of purchase for products damaged due to defect in workmanship and materials. Proof of purchase is required to obtain warranty service. Warranty is for replacement only. No service parts are available for these products. No other warranties are expressed or implied. Batteries are not covered under this warranty.
• For warranty service, please contact SECRUI Customer Service by email: contact@secrui.com
  IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN REPLACING BATTERIES

ABOUT COMPANY

• Manufacturer: Shenzhen Kerui Smart Technology Co., Ltd
• Address: Room 1501, T2, Jinlitong Building, No. 1100, Xingye Road Xin’an Street, Bao’ an District Shenzhen, Guangdong, China
• Email: support@secrui.com
• Youtube: Secrui Tech
• WEEE-Reg-Nr. DE 32683954
• Made in China
• Prolinx GmbH
  • Brehmstr. 56,40239 Duesseldorf
  • Germany
  • Telefon: +4921131054698
  • Email: eu@eulinx.eu
• NameBREPLAB CONSULTING LTD
  • Address: 28 Barletta House Vellacott Close, Cardiff, Wales, CF10 4AF
  • E-mail: UKREP@REPLAB.CC

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>