DS18 Hydro SB24BT 24 Inch Marine Water Resistant Amplified Owner’s Manual
- June 5, 2024
- DS18
Table of Contents
OWNER’S MANUAL
SB24BT
AMPLIFIED SOUND-BAR WITH
BT AND USB PLAYER
SB24BT
KNOWING YOUR SB24BT
- Main Power Wire
- 3.5mm Aux-Input
- USB Jack
- Control Panel
PACKAGING INCLUDES
1x SB24BT Soundbar
1x Remote Control
2x Tube clamp adjustable 1.5″ to 2.25″ diameter
4x NBR pad
1 set of screws and stop washers
NOTE: The stainless steel hardware supplied with your soundbar has been
chosen to resist rust and corrosion. If the particular hardware supplied will
not work for your installation purposes, please be sure to use only
appropriate marine grade (stainless steel) mounting hardware.
BT OPERATION
PAIRING & DISCOVERING A NEW BT CONNECTION
-
Long Press the Power Button 5 until the Soundbar Turns On
-
The SB24BT Will automatically go in to paring mode:
ANDROID AND IOS USERS:
A. Go into settings menu of your device
B. Enter the BT Menu
C. Turn On BT and press SCAN
D. “SB24BT” Will now be displayed under AVAILABLE
DEVICES
E. If Prompted, enter pass code: “0000” -
If SB24BT is not seen, repeat tha above steps to “refresh” the “device list”
-
When the connection is successful, you are now ready to stream music from your favorite media player to the SB24BT
BT STREAMING
MULTIFUNCTION CONTROLLER BT OPERATION
- Use this PLAY/PAUSE button 8 to Play or Pause the music from your device.
- Use this NEXT
**11**Button to select the next track or song on your playlist. - Use this PREVIOUS
**6**Button once to restart the song that is playing, or press again to go back to the previous song in your playlist.
VOLUME CONTROL
- press the
**VOL+10**Button to raise the volume or you can also use the volume control on your connected device. - To lower the volume press 7 the VOLUME DOWN button or use your device’s controls
TIPS
For maximum audio performance, depending of your type of music, you can change the EQ presets from your remote control to avoid distortion at hi-level of volume
AUX INPUT
AUX-IN OPERATION
- Long press the Power Button until the Soundbar Turns On
- Use a 3.5mm Jack cable from your device and connect it to the AUX-IN jack connector located behind the rubber cover on one side of the soundbar.
- The AUX mode is activated once the jack connector is in. now you can adjust the volume for your preference and play audio from your device.
TIPS
it is recommended to set the volume at a minimum 75% level before get
distortion from your device and only use the volume control from the soundbar
as a Master.
USB PLAYER
USB CONTROLS OPERATION
- Long press the Power Button 5 until the Soundbar Turns On
- Insert a USB Flash Drive on the USB Port 8 that is located behind the rubber cover at one side of the soundbar, once inserted the audio files start playing automatically
- Press the PLAY/PAUSE button to Play or Pause the Audio Files from your USB.
- Use this NEXT 11 Button to select the next track or song on your USB playlist.
- Use this PREVIOUS 6 Button once to restart the song that is playing, or press again to go back to the previous song in your USB playlist.
TIPS
The USB Player only Accepts MP3 and WMA Formats, also can be use as a 1 amp
charger Port
REMOTE CONTROL
REMOTE CONTROL OPERATION
- Make sure that the battery it is installed and the battery protector has been removed.
- The remote control needs to be pointed to the IR sensor (12) in the Soundbar to operates.
- press the desired function on the remote control: Power ON/OFF (1), Mode (2), EQ presets (3), Next (4), Vol- (5), Play/Pause (6), Vol+ (7), Previous (8), Folder down (9), Folder up (10)
REPLACEMENT BATTERY – CR2025
INSTALLATION
READ BEFORE INSTALLATION
- Be sure to carefully read and understand the instructions before attempting to install this soundbar.
- For safety, disconnect the negative battery terminal from the battery prior to beginning the installation.
- For easier assembly, we suggest you have all your tools in hand- Drill, Allen set, Crimp, Soldering iron, Wire Strippers, Heat-shrink, etc.
- Use high-quality “Waterproof’ connectors for a reliable installation and to minimize signal or power loss.
- Think before you drill! Be careful not to cut or drill into gas tank, fuel lines, brake or hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.
- Never run wires near fuel lines or power (if possible). Running the wires inside the hull or car area provides the best protection.
- Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through metal, especially on the Roll Cage.
- Make sure that the mounting clamp is tight before leaving the Vehicle.
INSTALLATION EQUIPMENT
– 5mm Allen Key
– Wrench Set
INSTALLATION
BEGINNING MOUNTING
Step 1: Remove the soundbar from the packaging and ALL hardware.
Step 2: Find a GOOD location that allows for easy wiring of the Soundbar
(Power Wire)-PLUS does NOT impair your movement around the location.
Step 3: Using 5mm Allen Key spin out the screw that holds the top clamp (if
was mounted)
Step 4: Use one of the supplied nuts (F) and insert this on the clamp base
(E), then slide the clamp base into the soundbar holder channel to the desire
location.
Step 5: Take the base clamp (D) and align it to the base clamp (E) hole and
secure it with the short screw (C) using a 5mm Allen key.
Step 6: Wrap the rubber pad around the pipe and lock the top clamp (B).
Step 7: Align the Clamp (B) with the base clamp (D) and use the supplied
screws (A) to tight down the clamps using a 5mm Allen Key.
Step 8: Do the same procedure on each clamp supplied, you may need an extra
help from somebody to hold up the Soundbar during the Clamp installation.
Step 9: Onces you tight very well all screws you can run the Power wire to the
battery location, use zip ties to secure the cable away from elements that can
damage it. This is it!! enjoy your new SB24BT Soundbar.
IMPORTANT
**** For water resistance purposes remove any USB or Auxiliary Cables and
be sure to put the rubber caps or covers in place before using this soundbar
in wet locations or when washing your vehicle.
CAUTION
**** Using other mounting methods may void this warranty
WIRING INSTALLATION
WE LIKE IT LOUD
DIMENSIONS
TROUBLESHOOTING
| TROUBLE | CAUSE | SOLUTION |
|---|---|---|
| Unit will not turn on | The fuse is blown | **Check/Replace the |
fuse
Main acc switch not engaged| Turn the switch to on position
No sound is heard| Device volume is low/muted| Turn the volume
level up
Cannot pair BT| The BT Function of the device
is not enabled| Refer to the user manual of the device for how to
enable the BT Function
The audio quality is poor after connection with a BT Enabled device|
The BT Reception is Poor| Move the device closer to the audio system or
remove any obstacle between the device
Unit has become unresponsive| Power glitch or interference|
Disconnect power for 10 seconds to reset**
SPECIFICATIONS
SPECIFICATIONS
Nominal Size ……………………………………………24.61″ / 625mm
Total Watts (Peak)……………………………600 Watts
RMS Power @ 4 ohm ……………………….100 Watts
Max Power @ 4 ohm ……………………………….200Watts
Frequency Response ……………………………………………45Hz-20KHz
Storage Temperature ……………………5°F ~ 176°F (-15°C ~ 80°C)
Operation Temperature …………………32°F ~ 140°F (0°C ~ 60°C)
Operation Voltage……………….12 Volts (10~16 Volts Range)
BODY
Marine Grade Type …………………………………IPX5
Body Material……………………….. Aluminum
Grill Type ……………………………….Steel Mesh / Malla de Acero
Qty on Box…………………………1 pcs / 1 Unidad
Clamps…………………………..2 Set (Tube Clamp Adjustable 1.5″ ~ 2.25″)
Front Logo ………………………………………….Yes / Si
RCA Line Out (Pre-Amp)…………………………………..No / No
Aux Line Input…………………………..Yes, (720mV) / Si, (720mV)
EQ ……………………………………5 Preset EQ (for BT and USB Mode)
Remote Out …………………………………………………………..No / No
USB Player …………………….Yes (WMA, MP3 files) / Si (Archivos MP3, WMA)
USB Charge ………………………………Yes (1Amp) / Si(1Amp)
Buttons | Controls /…Yes (Power, Mode, Play/Pause,,Fwd, Bwd,Vol+/Vol-)
Si (Encendido, Modo, Reproducir/Pausar, Adelante, Atras, Vol+/Vol-)
Remote Control ………………………………….Yes (IR Card Type)
Illumination ………………………………………Yes (Blue Backlit)
WOOFER SPECIFICATIONS
Nominal Diameter………………………………………………………3″ / 76.2mm (4 Pcs)
Voice Coil Diameter ………………………………………………..0.8″ / 20.4mm
Voice Coil Former Material ………………………………….Kapton
Cone Material ……………………Spk1: PPI / Spk2: Paper / Spk1: PPI
Surround Material………………………………Spk1: Rubber
Basket Material ……………………………………………………….Steel
Magnet Material …………………………………………………….Ferrite
Motor Diameter …………………………….2.36″ / 60mm
TWEETER SPECIFICATIONS
Nominal Diameter ………………………….0.94″ / 24mm (2 Pcs)
Voice Coil Diameter ……………………………………….0.8″ / 20.4mm
Type ……………………………………………….Dome
Diaphragm Material ……………Soft Dome
Magnet Material………………………….Neodymuim
Crossover …………………………………………………….6dB
SPECIFICATIONS
AMPLIFIER SPECIFICATIONS
Amplifier Class ………………………Class A/B
Amplifier Type …………..Stereo Full Range
Number of Channels…………………………………..4
Minimum Impedance………………………………4 ohm
Signal to Noise Ratio ……………………………….68dB
T.H.D………………………………………………….1% @ 1000Hz
Channel Separation………………………………………….60dB
Audio Source ………………………………………BT, USB, AUX,
Power Input Wire Size ……………………………2x16ga
Recommend Fuse Size ………………………………10A
MAX Current Draw ……………………….7A
Thermal Protection …………..Yes (>284°F / 140°C) / Si (>284°F / 140°C)
Over-Load Protection …………………………………………….Yes / Si
Short Circuit Output Protection ………………………..Yes / Si
Voltage Input Protection ……………………………………No / No
BT SPECIFICATIONS
Version …………………………………..V5
Audio Protocols………………………….A2DP
Range ……………………………>33ft (10m) / Class 2 / >33ft (10m) / Clase 2
MEASUREMENTS
Overall Width ………………….24.6″ / 625 mm
Overall Height ……………………………..3.98″ / 101 mm
Overall Depth ……………………………….3.98″ / 101 mm
FOR MORE INFORMATION
PLEASE VISIT
DS18.COM
We LIKE IT LOUD
Documents / Resources
| DS18
Hydro SB24BT 24 Inch Marine Water Resistant
Amplified
[pdf] Owner's Manual
Hydro SB24BT, 24 Inch Marine Water Resistant Amplified, Hydro SB24BT 24 Inch
Marine Water Resistant Amplified
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>