DANCING WINGS HOBBY SCG34 Bleriot XI Balsawood Scale Airplane Instruction Manual

June 13, 2024
Dancing Wings Hobby

SCG34 Bleriot XI Balsawood Scale Airplane

Product Information

The Balsawood Scale Airplane SCG34 ARF is a high-quality flying
model designed for experienced users. It has a wingspan of 1.8
meters, a fuselage length of 1.6 meters, and a fly weight of 5.8
kilograms. The product is made of balsawood and includes fiberglass
and carbon-fiber reinforced plastic parts. Please note that the
glue mentioned in the list may not be included due to air traffic
safety control.

Suggested Equipment

  • Engine: 2C DLE 35, 4C NGH 30/38
  • Prop: 20inch
  • Servo: 37g, 5pcs
  • Rx: 6CH

Tools Needed

To assemble and operate the SCG34-A kit, you will need the
following tools:

  • Tool Kit SCG34-A (included with the product)

Product Usage Instructions

  1. Pre-Flight Checks:

    • Check and adjust servo centering for better control surface
      adjustment.

    • Double-check the spinning direction of the motor before first
      usage to ensure it’s suitable for your model.

    • Set the center of gravity (CG) at the position marked in the
      manual. Add weight to the nose or tail if necessary for optimal
      flight performance.

    • Check the inside of the fuselage to ensure all equipment is
      correctly connected.

    • Inspect the heat-shrink covering material’s surface and ensure
      all screws, bolts, cabin, and canopy are secure.

    • Take care when connecting/disconnecting the battery. Replace
      the battery immediately if low voltage or damage is detected.

    • The connection of internal devices in the fuselage depends on
      your transmitter-receiver device. Check your device’s features for
      simplified connection instructions.

    • When pairing the power system and transmitter-receiver device
      for the first time, set the maximum stroke of the throttle
      yourself.

  2. Safety Precautions:

    • This product is not a toy and should be operated by experienced
      users. Children must be accompanied by an adult at all times when
      operating this product. Not suitable for children under the age of
    • Avoid flying around restricted locations such as airports,
      military bases, and residential areas.

    • Perform a range check on the transmitter to ensure no
      interference is present.

    • Always turn on the transmitter before the receiver and turn off
      the receiver before the transmitter.

    • If you are a beginner, seek assistance or advice from advanced
      expert fliers before flying your model.

    • Keep relevant items out of reach of children.

    • If engaging in high-stress flying, take necessary steps to
      control movement range and reinforce the body strength as you are
      solely responsible for it.

    • Some parts of this product may cause eye and skin discomfort
      due to fiberglass and carbon-fiber reinforced plastic. Wear goggles
      or dust-proof clothes when needed.

For more information, please visit the official website:
http://www.dwhobby.com/

PRE-FLIGHT CHECKS
Check/adjust servo centering, in order to adjust the control surface better.
Double-check the spinning direction of motor at first usage, and sure it’s suitable for your model.
CG Set the center of gravity (CG) at the position that manual already marked out. If necessary, add weight to the nose or tail to ensure the best flight performance.
Double-check the inside of the fuselage, make sure all the equipments are correctly connected; Check the heat-shrink covering material’s surface, Make certain all screws, bolts, cabin and canopy remain secure.
Take great care when connecting/disconnecting the battery, pls replace the battery immediately once found low voltage or damage to battery.
The way the internal devices of the fuselage are connected will be related to your transmitter-receiver device. For those transmitter-receiver devices with more functions, you can simplify the connection of the internal devices of the fuselage. Check your device for details to see if it meets the features you need.
When the power system and transmitter-receiver device are paired for the first time, you may need to set the maximum stroke of the throttle. Please set it yourself.
SAFETY PRECAUTIONS
14 This product should not be considered a toy, but rather a complicated and sophisticated flying model. Your safety depends on how you use and fly it, If not correctly operated, could cause injury to you or your family members. Children must be accompanied by an adult at all times if operating this product. Not suitable for children under the age of 14. THIS IS NOT A TOY.
Do not fly around some restricted location like airports, military bases, residential areas, etc.
You will need to range check the transmitter to be sure you are not experiencing any interference.
Always turn on the receiver last after turning on the transmitter and shut off the receiver first before turning off the transmitter.
If you are only a beginner to the radio control model flying, do not attempt to fly your model without any assistance or advice from advanced expert fliers.
Keep relevant items out of reach of children.
This product has been flight tested to meet or exceed our rigid performance and reliability standards in normal use,if you plan to perform any high-stress flying, you are solely responsible for taking any and all necessary steps to control movement range and reinforce the body strength.
This product may include some fiberglass and carbon-fiber reinforced plastic parts,which may cause eye and skin discomfort,pls wear the goggles or dust- proof clothes when needed.
Due to air traffic safety control, the products you receive may not have the glue that appears in the list. Please understand and purchase the glue you need at your local stationery store.
http://www.dwhobby.com/

Balsawood Scale Airplane

SCG34
ARF

Specification
:1.8M :1.6M : 5.8kg
Wingspan:1.8M Fuselage Length:1.6M Fly weight:5.8kg

Suggested Equipment
2C DLE 35 4C NGH 30/38
20inch 37g 5pcs 6CH
Engine : 2C DLE 35 4C NGH 30/38
Prop : 20inch Servo : 37g 5pcs Rx : 6CH

Tools Needed

KIT SCG34-A
SCG34-B

/ Photos shown here just for reference, the product you received maybe slightly differ from the photos due to continuous improvement on products.
SCG34-C SCG34-E

01 Assemble the Landing Gear 01-1

SCG34-E

SCG34-D

SCG34-G H

SCG34-F
SCG34-A: Fuselage SCG34-B: Wing SCG34-C: Horizontal tail/ Vertical tail SCG34-D: Landing Gear SCG34-E: Scale oil tank, Scale dashboard
SCG34-F Screws and accessories Rudder horn Wood block; Wood rod Connecting rod
SCG34-G: Tail wheel H: Carbon tube

Assenbly symbol guide

Ensure free rotation

Push tightly

x2 Repeat multiple times

1

Use medium CA
Use hobby knife with
Apply threadlock

Use thin CA

Use a pencil

Fully Tighten
Assemble right and left

OIL Apply Oil
Use epoxy adhesive
Epoxy glue

01-2

aa

b

01-3

Deleave the rear landing gear part as shown.
01-4
b
Insert into

a Insert into

Insert into a
01-6

01-5

Insert into location holes

a a

Insert the nose landing gear part as the picture shows, don’t fasten it, need to adjust later.
a Insert the rear landing gear into the prepared hole in the tail of fuselage, and note the part “A”installation.
CA a After inserting the rear landing gear into the location holes,fasten 2pcs “A” parts with CA glue, and keep the landing gear free rotation.
2

02 Assemble the fuselage bracing wire 02-1
M1

Drill holes as in the picture above, and install self-tapping screws with ring.
02-2

X12
Screw for the ring

Screw M3x18mm

X2

M3*15mm+ Screw+nut

02-3

Screw M3x18mm

X2

1
2
Steel bracing wire

102-12 Fuselage’s bracing wire is one piece wire rope, start at “1” as above picture shown, pass through the rings which you installed on step “02-1”,until end at “2”.
3

02-4 02-8

02-9

Install the bracing wire on the other side with same installation way on step “02-3”.

02-5

02-6

X4 Screw
M3*15mm

4 Unscrew into 4pcs steel wires from the bottom of fuselge.
02-10

+M3 Screw+Self-locking nut

+screw mandrel +carbon tube

Nut M3

02-7

X4
03 Assemble the Tail Wing 03-1

X2
M3 Self-locking nut

03-2

15.5mm

03-3

X4
M2*10mm+ Screw+Nut
After adjusting the left and right length,locking the screw for fixing rocker arm.
4

03-3

03-4

M1.5

2mm
Plug control surface,fasten the joint with tape, and adjust the gap.
03-6

03-5
Self-tapping screw
X2 M3x10mm

Remove tape, adjust rocker arm, keep it vertical with surface.
03-8
Epoxy glue

03-7
Lubricant oil Same installation way in following steps for this part.

Add some lubricating oil in the joint of needle type hinge.(Avoid the glue stuck dead.) Before install and fasten the needle type hinge with epoxide- resin glue , pls confirm the rudder surface can swing freely in advance.
03-9

03-10

X2

Epoxy glue

5

Drill hole as shown, and fasten with self-tapping screw.

X2

Screw M4x45mm

Install vertical tail wing on the tail of fuselage, fasten with epoxy glue, and keep the tail wing swinging freely.

04 Assemble the wing 04-1
Epoxy glue

04-2

04-3

Lubricant oil Install aileron, keep it swinging freely.

Install aileron’s servo as shown, stick wood block as an auxiliary.

04-4

X4
Self-tapping screw M3x10mm
04-5

Screw M3*10mm

Screw+ Self-locking nut M3*15mm

Screw M3x10mm

X4

8 Install “8” shape rings on the prepared holes in both sides of wing, fasten with screws.

6

04-6

04-8

Carbon rod M14x720mm

04-7
Hand screw M4x20mm

05 Installation of control servos for horizontal tail and vertical tail 05-1

X4

05-2
High position servo

05-3

Low position servo
Pay attention to the servo’s putting direction.

Install rocker arm as shown.

Install rocker arm on the servos as shown,through 2pcs steel bracing wires to control elevator and rudder separately. This 2pcs bracing wires are uncrossed.
7

05-4

2 Low position servo control rudder, control by 2pcs steel bracing wire, and link with rear tail wheel. Installation way as shown in left and right pictures.Lock the end of steel bracing wire with alu buckle.

Connect the horn on steering rudder

Fastener

Alu buckle

05-5

Low position servo

Connect the rocker arm on servo

05-6
High position servo

Fastener

Alu buckle

2 High-position servo controls the elevator, controlled by 2pcs steel bracing wire. Note to pass through the 2pcs round rings on the tail of fuselage, installation way as shown in right picture. Lock the end of steel bracing wire with alu buckle.

05-7
Round ring
05-8
Rocker arm

Rocker arm
Round ring
8

06 Installation Installation for the wing bracing wire Take the one side wing bracing wire as an example, the left and right installation in same method.
2
2

1

1

3

3

123 There are each 2pcs steel bracing wires up and down, start at “1” as above picture shown, pass through “2”,until end at “3”.Use alu buckle to tie a knot on both ends.

X2 Self-tapping screw
M3x10mm
9

07 Assemble the engine

Strengthen the firewall with triangle wood around and stick with epoxy glue.

F25-2

F25 F25-1

F25-2

After installation and adjustment of engine, adjust the extension length of landing gear, until without influence for propeller, then drill holes on the screw position as shown, fasten the landing gear with screw lastly.

M3

M3*15mm+ Screw+nut
X4
10

08 Assemble the scale decoration parts

F22-1

Balsawood strip
F22 F22

F22-1

Balsawood strip

09 Set and Adjust

Display the C.G

75mm

C.G

Usually, the control throws set as below:
75mm

Aileron
20°-35°
20°-35°

25°

25°

25°

25°

Elevator

Rudder

(Normal Flying)

3D (3D Flying only support some models)

Aileron

±15°-30°

±40° (or larger)

Elevator

±15°

±40° (or larger)

Rudder

±15°

±40° (or larger)

Flap take-off15°-20° Landing20°-40°

V Some special models will have V-tails, flaps, leading edge wings, etc., which can be used as a reference for conventional flight angles. If you do not confirm and there is no experienced person to guide you, we recommend that you first test at a small angle to confirm that your settings are correct.

When using an oil-powered engine, it maybe necessary to counterweight the head of the airplane, and the oil tank is placed at the center of gravity.

When using the electric motor,the center of gravity can be adjusted by adjusting the position of the battery.

11

12

Control Directions Tests

Lifting rod down

Elevator

Lifting rod up

NOTE

Steering rod to the right

Aileron

Steering rod to the left

Direction rod to the right

Rudder

Direction rod to the left

More details about power system adjustment, please refer to below link: (You can scan QR Code directly.)
http://www.dwhobby.com/art/connection

13

14

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals