signify LEDALITE ID-39 Drywall Corners User Guide
- June 15, 2024
- signify
Table of Contents
signify LEDALITE ID-39 Drywall Corners User Guide
SYSTEM OVERVIEW
These instructions review how to install drywall versions of TruGroove recessed corners. Please refer to layout drawings supplied by Ledalite with these installation instructions. These instructions must be used in conjunction with TruGroove Drywall Ceiling Standalone and Continuous Run Installation Instructions. The graphics below show the corner types available, and steps required to correctly install TruGroove corners in drywall ceilings or walls. These instructions apply to trim and trimless TruGroove product configurations. IMPORTANT: Read all instructions including fixture wiring AND mechanical details before beginning installation.
Corner Type Detail
- A. Flat Corner: In-Ceiling Option available in trim and trimless configurations. Wall-to-wall option available in trimless configuration only.
- B. Inside corner: for wall-to-ceiling and wall-to-wall installation, available in trimless configuration only.
- C. Outside corner: for wall-to-wall installation, available in trimless configuration only.
IMPORTANT INSTALLATION STEPS (TRIMLESS VERSION):
- Install required mounting brackets (if applicable).
- Install framing/blocking as per supplied layout drawings and instructions.
- Install drywall.
- Install all lighting fixtures.
- Install corner bead(s) and tape.
- Mud, sand and finish wall(s) and ceiling(s).
Fixture Type Information:
TruGroove corners have 2 light distribution options. Follow the drawings below
and refer to layout drawings for proper identification of specific fixture
orientation and location.
IMPORTANT: Identify each fixture type and location before installing any
fixtures in ceiling or walls.
Ceiling Cut-out Information:
Continuous run ceiling and wall cut-out dimensions shown below come from
supplied layout drawings.
IMPORTANT: Layout drawings for all patterns show dimensions to corner centres.
Framing, ceiling and wall preparation must be done according to provided
layout drawing pattern leg dimensions and detailed instructions on pages 3 and
4. For corner installation in wall, refer to instructions on pages 6, 7 and 8.
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interreference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Corner type `A’: Flat Corner In-Ceiling
For continuous run fixtures, the cut-out in the drywall ceiling should be
measured and cut as shown on page 3 and 4. Refer to drywall ceiling standalone
and continuous run install instructions for fixture mounting location details.
Determine corner location and refer to figure A for specific in-ceiling corner
mounting dimensions.
Corner Type `B’: Inside Corner Wall-to-Ceiling or Wall-to-Wall
Inside corner installation in wall-to-ceiling and wall-to-wall configurations require the use and installation of inside corner kit components shown in figure B below.
Installation of an end fixture at a wall end does not require the use of an
inside corner kit. Prior to installation of this fixture module, remove
factory installed metal end trim and 2 large head screws and shown in step 6.
Install end fixture module as shown on page 8.
Corner Type `C’: Outside Corner
© 2021 Signify Holding. All rights reserved. The information provided herein is subject to change, without notice. Signify does not give any representation or warranty as to the accuracy or completeness of the information included herein and shall not be liable for any action in reliance thereon. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract, unless otherwise agreed by Signify.
Signify North America Corporation 400 Crossing Blvd, Suite 600
Bridgewater, NJ 08807
Telephone: 855-486-2216
Signify Canada Ltd.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Telephone: 800-668-9008
All trademarks are owned by Signify Holding or their respective owners.
www.ledalite.com Revision D www.signify.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>