WALI MF002-W Dual Monitor Desk Mount Instruction Manual

WALI MF002-W Dual Monitor Desk Mount

Product Information

• The Dual Monitor Desk Mount (MF002/MF002-W) is a versatile mounting solution designed to securely hold two monitors.
• It has a weight capacity of 10kg/22 lbs per monitor and is compatible with VESA mounting patterns of 75×75 and 100×100. The maximum monitor size supported is 27 inches.

Product Usage Instructions

Installation

1. Attach Pole A to Weighted Base B using 3pcs M5x14 Bolts E and tighten with the Allen Key 3mm I.
2. Insert Wire Clip G and Swivel Arm C through Pole A, adjust the preferred height, and tighten using Allen Key 5mm I.
3. Attach Wire Clips H to Swivel Arm C.

Attaching the Monitor

1. Select the appropriate bolts and spacers for your TV/Monitor.
2. Attach the VESA Plate D to the Monitor and tighten it with a screwdriver.

• Step 3.1: Select Monitor Screws
• Step 3.2: Select Spacers (if needed)
• Step 3.3a: Flat Back Monitor
• Step 3.3b: Curved or Recessed Back Monitor

Mounting the Monitor

• Place the assembled TV/Monitor onto Swivel Arm C and tighten the VESA Plate D with Nut F for stability.
• If one monitor is lower, remove Nut F and adjust the bolt counter-clockwise using Allen Key 3mm I to raise the monitor.
• Tighten the VESA Plate D with Nut F for stability after the adjustment.
• Ignore this step if monitors are level.

Safety Precautions

For safety, do not extend the arms too far forward or backward as this may cause instability and tip-over.

Cable Management and Adjustment

7. Guide the cable through the Wire Clips (nG1, nH2) and store the Allen Keys or in the Wire Clip nG1.
8. Adjust the tilt angle using Allen Key 5mm nI. Manually swivel, tilt, and rotate the monitor for the best viewing angle.
9. Make sure the security nut hF is installed before rotating the monitor.

Note: Ensure that both arms are aligned and balanced.

Specifications

• Weight Capacity: (10kg/22lbs) x 2
• VESA Compatibility: 75×75, 100×100
• Maximum Monitor Size: 27 inches

FAQ

Q: What is the weight capacity of this dual monitor desk mount?

• A: The weight capacity is 10kg/22lbs per monitor.

Q: What VESA patterns are supported?

• A: The mount supports VESA patterns of 75×75 and 100×100.

Q: What is the maximum monitor size that can be used with this mount?

• A: The maximum monitor size supported is 27 inches.

Q: How should I adjust the tilt angle and position of the monitors?

• A: Use the provided Allen keys to manually swivel, tilt, and rotate the monitors for the best viewing angle.
• Ensure that the security nut is installed before rotating the monitors.

WARNING

• If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician.
• Check carefully to make sure there are no missing or defective parts.
• Improper installation may cause damage or serious injury.
• Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity.
• We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.

TIP OVER WARNING

• SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT TIPOVER:
• NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
• USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
• THE USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIPOVER.
• SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

Supplied Parts List

INSTALLATION INSTRUCTION

1. Install Pole A to the weighted Base b using 3pcs M5x14 Bolts e, and tight E ten with the Allen key 3mm o .1
2. Put the Wire Clip and Swivel Arm C through the Pole a, adjust the preferred height, and tighten using Allen Key 5mm I. Attach the Wire Clips h to the Swivel Arm C.
3. Select bolts and spacers (if needed) according to your TV/Monitor. Attach the VESA Plate to the Monitor and tighten it with a screwdriver. (Screwdriver not included)
4. Put the assembled TV/Monitor onto the Swivel Arm d and tighten the VESA Plate e with Nut h for stability.
5. If one monitor is lower, remove the Nut h and turn the bolt counter-clockwise using the Allen key 3mm o to raise the monitor. Tighten the VESA Plate e with Nut h for stability after the adjustment.
6. For safety, please do not extend the arms too far forward or backward. This may cause instability and tip-over.
7. Guide the cable through the Wire Clips ( n1, n2 ) and store the Allen Keys o in the Wire Clip n1.
   • Adjust the tilt angle using Allen Key 5mm n.
   • Manually swivel, tilt, and rotate the monitor for the best viewing angle.

• www.walielectric.com
• support@walielectric.com
• 1-844-SATTLER (18447288537)

Documents / Resources

| WALI MF002-W Dual Monitor Desk Mount [pdf] Instruction Manual
MF002, MF002-W, MF002-W Dual Monitor Desk Mount, MF002-W, Dual Monitor Desk Mount, Monitor Desk Mount, Desk Mount, Mount
---|---

References

• TV mount, Monitor mount, Desk mount, TV Stand, Speaker mount,

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>