HALO IB51872422 6 and 4 Inch Direct Mount Night Light Instructions
- June 15, 2024
- HALO
Table of Contents
HALO IB51872422 6 and 4 Inch Direct Mount Night Light Instructions
Packaging Contents
Night Light DM (NL-DM) and connector
Night Light DM (NL-DM) y connector
Night Light DM (NL-DM) et connecter
CCT Selector Switch (D2W, 2700K, 3000K, 3500K, 4000K & 5000K)
Choose your favorite correlated color temperature (CCT) from 6 options using
the switch
ITEMS REQUIRED
(Purchase separately)
- Gloves
- Ladder
- Screwdriver
- Hole Saw
- Safety Glasses
Optional
- Drill
- Screws for mounting (if required by local code)
IMPORTANT SAFETY INSTRUCTIONS
Read and follow these instructions and heed all warnings, including those on the product. Failure to do so may result in serious bodily injury or property damage.
When using product, basic precautions should always be followed, including the following:
- Read and follow these instructions.
- HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.
- SAVE THESE INSTRUCTIONS AND WARNINGS.
WARNING
Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an
electrician
Risk of Electric Shock – To avoid possible electrical shock, be sure that
power supply is turned off at fuse box or circuit breaker before installing or
servicing luminaire.
Risk of Fire/Electric Shock – LED DM Fixture installation requires
knowledge of luminaires electrical systems. If not qualified, do not attempt
installation. Contact a qualified electrician. Luminaire wiring and electrical
parts may be damaged when drilling for installation of LED DM fixture. Check
for enclosed wiring and components.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
CAUTION
Edges may be Sharp – Wear gloves while handling.
- Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
- Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during fixture installation.
- This device is not intended for use with emergency exits
DIMMING
Halo Night Light DM (NL-DM) is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. Note some dimmers require a neutral in the wall box.) For the latest Halo NL-DM product information, please refer to specifications online at www.cooperlighting.com.
COLOR SELECTION
The Selector Switch allows the choice of several different color temperature options (switch set to 3000K by default). To view the different color options, move the switch position to the desired color temperature. Power does not need to be disconnected during color selection.
INSTALLATION
The NL-DM models should be installed directly into a ceiling without requiring separate junction box or recessed housings. They are wet location covered ceiling rated for installation into areas such as ceilings of porches with permanent roofs.
WARNING
Risk of Electric Shock – To avoid possible electrical shock, be sure
that power supply is turned off at fuse box or circuit breaker before
installing or servicing luminaire.
WIRING
-
Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1 ). Make sure the opening is not larger than the outer flange of the LED module.
-
Open the cover of the provided jbox and insert the supply wires through the preferred strain reliefs in the provided jbox (Figure 3 ).
Make a 90° L shaped bend in the cable inside the jbox immediately after the plastic wire trap (Figure 6).
Connect the bare copper (ground) wire from the jbox to the ground wire of the supply connection using the provided wire nut.
- Connect the black/white leads from the output of the driver to the appropriate supply side wiring using the provided wire nuts.
- Close the cover after properly securing the supply wire to the provided jbox on the rear of the LED module.
- Use the CCT selector switch to select the desired color temperature.
- Module is ready to install into ceiling. (See MOUNTING section for specific instructions).
MOUNTING
-
Connect the remote driver box to the light fixture. (Figure 2)
-
Place remote driver box thru the cut-out hole and mount according to local code as required.
-
Bundle any excess wire and place into ceiling above the module according to local code as required.
-
Rotate both mousetrap springs upward to allow passage through the cutout in the ceiling. (Figure 4).
Optional ceiling ring to be placed between module trim and ceiling.
-
Continue to press the module through the cutout in the ceiling until the perimeter flange of the module is flush against the ceiling. ( Figure 5)
-
The springs will rotate back into position and hold the LED module tight to the ceiling.
MOUNTING USING OPTIONAL MOUNTING FRAME
-
Place remote driver box onto mounting frame, using studs on mounting frame as a guide (Figure 7).
-
Position remote driver box as shown and secure with provided thumb nuts (Figure 8).
CAUTION
Risk of pinching – Do not place hands or fingers under springs during
removal of the LED module.
REMOVAL
- Simply pull down firmly on LED module until mousetrap springs release from the ceiling. Reach through the ceiling to hold mousetrap springs up and away from the ceiling as you continue to pull the module from its opening.
- Disconnect wiring.
OPERATION
Downlight Mode:
- Cycle wall switch to ‘ON’ position to turn on downlight.
- Cycle wall switch to ‘OFF’ position to turn off downlight.
Nightlight Mode:
- With wall switch in ‘ON’ position (downlight on), cycle wall switch ‘OFF’ and back to ‘ON’ within 0.2-1.5 seconds. Fixture should illuminate in nightlight mode.
- Fixture will default to downlight mode when the wall switch is cycled ‘OFF’ and then ‘ON’.
YEAR LIMITED WARRANTY
Limited warranty for five years, based on up to 6 hours of usage per day.
Additional terms and conditions apply. For more details, please visit:
www.cooperlighting.com/warranty
FCC Statement
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
- This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).
Cooper Lighting Solutions
1121 Highway 74 South Peachtree City, GA 30269
P: 770-486-4800
www.cooperlighting.com
Canada Sales
5925 McLaughlin Road Mississauga, Ontario L5R 1B8
P: 905-501-3000
F: 905-501-3172
© 2022 Cooper Lighting Solutions All Rights Reserved Printed in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>