Commercial Electric LM2n400042WNG 4ft Motion Sensor Activated Led Wrap Light With Night Light User Guide

SKU# 1001 668 048
Model #LM2n400042WNG
Model #LM2n400042WNGTH
USE AND CARE GUIDE
4FT. MOTION SENSOR ACTIVATED LED
WRAP LIGHT WITH NIGHT LIGHT

THANK YOU
We appreciate the trust and confidence you have placed in Commercial Electric through the purchase of this LED Motion Sensing Color Changing Wrap Light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Commercial Electric!

Safety Information

For your safety, always remember to:

• Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
• Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber soled shoes and work on a sturdy wooden ladder.
• Account for small parts and destroy packing material, as these may be hazardous to children.

This fixture is designed for use in a circuit protected by a fuse or circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
WARNING: RISK OF SHOCK. House electric current can cause painful shock or serious injury unless handled properly.
CAUTION: Turn off the main power at the circuit breaker before installing the fixture, in order to prevent possible shock.
NOTICE: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical wiring connections obtain the services of a qualified electrician.
Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.

Warranty

LIMITED WARRANTY
This product is warranted to be free from defects in workmanship and materials for up to 5 years from date of purchase. If it fails to do so, please contact the Customer Service Team at 1-877-527-0313 or visit www.homedepot.com

Pre-Installation
TOOLS REQUIRED

Installation

1. Preparing to mount housing to the ceiling
   • Turn OFF the main power at the circuit breaker before the installation.
   •  Locate the electric power supply junction box that is being used for this installation.
   •  Ensure that the center hole on the housing (B) will be aligned with the junction box.
   •  Mark 2 screw hole locations on the ceiling, 40 3/25in. apart. Drill two holes in the drywall celling at the marked locations.
   •  Install an drywall anchor (AA) in each of the drilled mounting holes.
   •  Insert screw (BB), tighten each screw leaving a small space away from the ceiling.
   

2. Removing the diffuser from the housing
   •  Step 1: Press down on the end of the diffuser (A) opposite of the end cap with the motion sensor.
   There is a tab that the diffuser has to slide underneath to allow it to be removed.
   •  Step 2: Slide the diffuser (A) toward the end being pressed down opposite the end cap with the motion sensor.
   •  Step 3: Lift the diffuser (A) from the side with the motion sensor to remove the diffuser.
   •  Step 4: Remove the metal access plate that covers the center hole on the housing(B).
   
   Installation(continued)

3. Selecting the CCT and Sensor Time
   • This product includes the feature to select the color temperature (CCT) at the point of installation.
   • Locate the CCT switch of the housing. Move the switch to the desired CCT: 3000K (warm white), 4000K (cool white), or 5000K (daylight).
   • Locate the sensor time select switch on the side of the housing. Move the switch to the desired sensor time selection. 1min, 10min, OFF. The sensor is both workable for the main light and night light mode.
   

4. Installing the housing
   • Please ensure to turn OFF the main power at the circuit breaker before connecting the wires.
   • Locate the two key holes on the housing on each end.
   • Place one side of the housing key hole on the mounting screw previously installed on the ceiling from step 1. Repeat with the other side.
   • Slide the housing in place until it is secure.
   • Feed the electric power supply wires through the center hole.
   • Tighten the mounting screws to secure the housing to the ceiling.
   

5. Connecting the wires
   • Identify the wiring located inside of the housing: (black – line voltage, white – neutral, green – ground).
   Feed the wires from the housing through the center hole.
   • Connect the Black (L), White (N) and Green (G) wires from the fixture to their corresponding wires from the junction box using Wire Nuts (CC).
   • Position the connected wires back into the junction box.
   

6. Installing the diffuser
   • Tighten the screw of the access plate on the center of housing(B)
   •  Reinstall the diffuser to the housing by inserting one side into the end cap opposite of the motion sensor until it can no longer slide in that direction.
   •  Then slide the diffuser in the opposite direction to tightly secure in place.
   •  Restore power to the electrical box.
   •  Turn on the light switch to activate the xture.
   •  Using the light switch can exchange the night light mode and wrap light mode.
   

7. Turning on the light
   • Restore power to the junction box. Turn the light switch on to activate the xture.
   •  Selecting Main Light or Night Light Mode
   •  To turn on the main light mode, switch on the wall switch.
   •  To change to night light mode, turn on the main light, then switch the wall switch off then back on again within 2 seconds.
   •  When the light is in night light mode, and motion is detected, it will come on in night light mode. When the light is in main light mode, and motion is detected, it will come on in main light mode. The light mode will stay for the timer you select 1min/10min/OFF.
   NOTE: The Main light will not provide light output while in night light mode.
   □ To return to main light mode after using night light mode, switch the wall switch off then back on again within 2 seconds.
   

Care & Cleaning

CAUTION: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box.

• Clean the fixture with a soft, dry cloth.
• Do not use cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

WARNING: Before doing any work on the fixture, disconnect power to the light fixture by turning the breaker off or removing the fuse from the fuse box.

Troubleshooting

on.
The circuit breaker is off.| Ensure the circuit breaker is in the on position.
A wire is not properly connected.| Check to ensure proper wire connections
are made. Contact a qualified electrician.
The switch is defective.| Contact a qualified electrician.
The fuse is blown or circuit breaker is tripped when turning on the light.| The wires are crossed or the power wire is ground out.| Check the wire connections.
Contact a qualified electrician or call
Commercial Electric customer service at 1-877-527-0313.

Light Distribution

Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313
HOMEDEPOT.COM
Retain this manual for future use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>