Commercial Electric 567071111 Color Selectability Flushmount Instruction Manual

May 15, 2024
Commercial Electric

Commercial Electric 567071111 Color Selectability
Flushmount Item # 1009595408
Model # 567071111

UsE aNd CarE GUIdE
4fT. x 10IN. COlOr sElECTabIlITy flUshMOUNT

PACKAGE CONTENTS

Commercial Electric 567071111 Color Selectability Flushmount - overview
1

Part Description Quantity
A Fixture Body 1
B Fixture Diffuser 4

HADWARE INCLUDED

Part Description Quantity
AA Wire Connector 3
BB Drywall Anchor 2
CC Mounting Screw 2
DD Safety Cable 2

Commercial Electric 567071111 Color Selectability Flushmount - overview
2 NOTE: Keep your receipt and these instructions for proof of purchase.
WarNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.

INSTALLATION

  1. Turn the diffuser (B) counterclockwise to remove it from each end the housing plate.

  2. Hold the fixture body (A) up to the ceiling to determine the best mounting position for wiring the fixture. Mark two keyhole locations for mounting.Commercial Electric 567071111 Color Selectability Flushmount - INSTALLATION NOTE: The distance between the two keyholes on fixture body (A) is 35.28 in.

  3. Drill four 1/8-in. pilot hole into the screw locations marked on the ceiling. Insert the drywall anchors (BB).

  4. Fix the two safety cable (DD) by mounting screws (CC) on the holes of surface,but do not tighten fully. Then hook with the fixture body (A) through the hole on the cable (DD).

  5. Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A).
    Connect the green wire from the J-box to the grounding wire from fixture (A). Cover the wire connections using the wire nuts (AA).Commercial Electric
567071111 Color Selectability Flushmount - INSTALLATION
1

  6. Position the wires back inside the electrical box.

  7. Align the 2 mounting keyholes on the fixture (A) with the 2 mounting screws (CC) in the ceiling. Once the screw heads are through the large ends of the keyholes, slide the housing until the heads of the screws slide into the narrow ends of the keyholes. Finish tightening the mounting screws (CC) until the fixture (A) is tightly secured to the mounting surface.Commercial Electric 567071111 Color Selectability Flushmount - INSTALLATION 2

  8. Reattach diffuser

  9. Turn on the power and light the lamp, and move the toggle switch to the desired color temperature gear (as shown below, 3000K Soft White, 4000K Bright White and 5000K Daylight).
    NOTE: The factory setting for the correlated color temperature (CCT) is 3000K.

Commercial Electric 567071111 Color Selectability Flushmount - INSTALLATION
3 SELECTING MAIN LIGHT Or NIGHTLIGHT MODE
The product can be used in one of two modes: Main light mode, which provides full brightness and allows selection from three color temperatures, or nightlight mode.
Night light mode provides reduced light output at 2000K color temperature for very soft illumination at night.
TO TURN ON THE MAIN LIGHT

  1. Turn on the light switch to activate the light fixture.

TO CHANGE TO NIGHTLIGHT MODE

  1. Switch the main light off and back on again in 3 seconds to active nightlight mode.

NOTE: The main light will not provide light output when the nightlight trim is illuminated.
TO RETURN TO THE MAIN LIGHT

  1. Toggle the switch off and back on to active.

CARE AND CLEANING

CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the
breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or
harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.

TROUBLESHOOTING

Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.

Problem Possible Cause Solution
The fixture will not illuminate. The power is off. Ensure The power supply

is on.
The circuit breaker is off.| Ensure The circuit breaker is in the on position.
There is a bad connection.| Check to ensure proper wire connections are made. Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips when the light is turned on.| The wires are crossed or the power wire is grounding out.| Check the wire connections.
Contact a qualified electrician or call customer service 1-877-527-0313.
The light fixture flickers or makes a buzzing sound.| The dimmer circuit is not compatible with the product.| Check the product page at www.HomeDepot.com for a list of compatible dimmers.
The dimming circuit is set outside the dimming range of the product.| Turn or slide the dimmer switch to adjust the light output until the flickering or buzzing stops.
Out of sync| Slide the dimmer too fast.| Turn off the wall switch for more than 3 seconds, then turn back on.
The dimmer circuit is not compatible with the product| Check the product page at www.HomeDepot.com for a list of compatible dimmers.

WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation.
Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.

  • Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker.
  • To reduce the possibility of serious injury, always take the proper precautions and unplug the fixture before moving or cleaning.
  • Risk of fire or electric shock.

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARRANTY

WHAT IS COVErED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
Contact the Customer Service Team at 1-877-527-0313 or visit www.HomeDepot.com.

Questions, problems, missing parts? Before returning to the store,
call Commercial Electric Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday
9 a.m. – 6 p.m., EST, Saturday
1-877-527-0313 | HOMEDEPOT.COM
Retain this manual for future use.

Documents / Resources

| Commercial Electric 567071111 Color Selectability Flushmount [pdf] Instruction Manual
567071111 Color Selectability Flushmount, 567071111, Color Selectability Flushmount, Selectability Flushmount, Flushmount
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Commercial Electric User Manuals

Related Manuals