amazon basics B08J4J2FNY Contemporary Single Cylinder Door Handleset with Madison Lever User Guide
- June 15, 2024
- amazon basics
Table of Contents
amazon basics B08J4J2FNY Contemporary Single Cylinder Door Handleset with
Madison Lever
Scan the QR Code and scroll through the images to find an assembly or how-to video
TOOLS
Product Description
Deadbolt lock
Door handleset
Installation
NOTICE
This product is classified as “full indoor type” and should only be installed
in indoor environment.
NOTICE
Determine the door handing before installing the product.
Face the door from the exterior side:
- If the hinges are installed on the left, the door is left-handed.
- If the hinges are installed on the right, the door is right-handed.
NOTICE
- Prepare all the tools required for the installation.
- Follow the steps in chapter “Instructions for doors with existing holes” at the back of the manual to install the deadbolt lock (P. 18-25) and door handleset (P. 26-35). For drilling, read chapter “Drilling instructions” (P. 36-42).
- Illustrations in the steps in chapter “Instructions for doors with existing holes” and “Drilling instructions” are for left-handed doors. Reverse the lever position for right-handed doors.
Instructions for doors with existing holes
Drilling instructions
- Confirm that the hole in door edge is 01″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″ (45 mm) thick. Also confirm that the hole in the door is 02-1 /8″ (54 mm).
- Hold the latch (D) with the latch face flush against the door edge. Ensure that the slot is centered in the door hole. Adjust the latch if needed.
-
Optional – for doors with chiseled pocket: pry open the attached latch face plate (E) and replace it with the rectangular one.
-
Optional – for doors without chiseled pocket: pry open the face plate holder with a flat-head screwdriver. Attach the drive-in collar (F) to the latch.
-
For latch with face plate (El: fit the latch into the hole and secure with two screws (Gl. / For latch with drive-in collar (Fl: insert the latch with drive-in collar and tap into position using a wood block and hammer.
- Mount the exterior chassis (C) on the door. The torque blade of the cylinder (B) must pass through the slot on the latch (D).
- Fit the interior thumb turn (I) onto the torque blade. Run two bolts (J) through the interior thumb turn (I) into the holes of the latch (D) and tighten them.
- Ensure that the door frame hole is at least 1″ (25 mm) deep. Mount the strike plate (HJ on the door frame with two screws (G).
1. Confirm that the hole in door edge is 01″ (25.4 mm) and the door is between 1-3/8″ (35 mm) and 1-3/4″ (45 mm) thick. Also confirm that the hole in the door is 02-1 /8″ (54 mm).
2. Place the template on the door aligning the hole marking with the door hole. Mark the bottom screw hole on door.
3. Drill a hole on the marked position using 03/8″ (10 mm) drill bit.
4. Hold the latch (NJ with the latch face flush against the door edge. Ensure that the square hole is centered in the door hole. Adjust the latch if needed.
5. Optional – for doors with chiseled pocket: pry open the attached latch face plate (0) and replace it with the rectangular one.
6. Optional – for doors without chiseled pocket: pry open the attached latch face plate (OJ. Remove the face plate holder and attach the drive-in collar (P)
7. Latch with face plate (O): fit it into the hole and secure with two screws (Q). / Latch with drive-in collar (P): insert it and tap into position using a wood block and hammer. Latch bolt bevel must face to closing direction.
8. Mount the exterior lever (Kl on the door with the washer (Ll and bottom bolt (Ml. The middle bolt of the lever must pass through the slot on the latch (Nl.
9. Mount the interior lever (SJ on the door with two bolts (T)
10. Ensure that the door fr me hole is at least 1″ (25 mm) deep. Mount the strike plate (R) on the door frame with two screws (Q).
1. Use template to mark holes on door, Fold template along fold line and place it along the door edge, Select the drilling point for different door thickness: 1-3/8″ (35 mm), 1-9/16″ (40 mm) or 1-3/4″ (45 mm),
2. Drill the pairs of holes using chisel and circular drill bits. NOTICE Drill from one side until the drill just breaks through, then complete hole from the other side to prevent wood from splintering.
3. Mark the outline of the face plate (E, 0). Chisel 5/32″ (4 mm) deep for the face plate (E) and 1 /8″ (3 mm) deep for the face plate 0).
4. Mark the positions of the screw holes. Drill two 1″ (25 mm) deep holes using 1/8″ (3 mm) drill bit.
5. Close the door and mark the op and bottom position of the latch across the door frame. Open the door and measure the distance X from the exterior door edge to the flat end of the latch.
6. Mark a vertical line on the door frame for the measured distance X from the outside to the inside. Position the strike plate (H, R) within the guidelines. Mark and drill two 1″ (25 mm) deep screw holes using 1/8″ (3 mm) drill bit.
7. Mark and drill a 1″ (25.4 mm) hole with 1″ (25 mm) depth at intersection of horizontal and vertical line of the cutout of the strike plate (H, R).
8. Chisel 5/64″ (2 mm) deep for the strike plate (H) and 1 /16″ (1.6 mm) deep for the strike plate (R).
MADE IN TAIWAN
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>