Item # 1000000000/ 1000000000
Model # 538661010/ 538671010
UsE ANd CARE GUIdE
LEd sqUARE CANLEss sLIM dOWNLIGhT WITh NIGhTLIGhT
4 IN., 6 IN.

PACKAGE CONTENTS

NOTE: Keep your receipt and these instructions for proof of purchase.
WARNING: rIsK of ELEcTrIc shocK. Ensure the electricity to the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.

INSTALLATION

Item # 1000000000/Model # 538661010 can be installed into holes cut in the drywall that are between 4” and 4 1/3”, 4” is suggested.
Item # 1000000000/Model # 538671010 can be installed into holes cut in the drywall that are between 6” and 6 1/3”, 6 1/4” is suggested.

1. Make sure the power is turned off at the source to the location where the LED downlight (A) will be installed.
   If InsTALLIng ThE LED DownLIghT (A) In A PrEExIsTIng hoLE:
   a. remove the existing can or fixture and set aside since it will not be needed.
   b. Measure the ceiling hole to make sure it is the correct size for the fixture.
   If InsTALLIng ThE LED DownLIghT (A) In A nEw cEILIng LocATIon:
   a. Place the hole template (c) over the desired location and trace the outline with a pencil.
   b. cut out the marked opening in the ceiling with a hole saw (not included).
   NOTE: 1/2” or 5/8” drywall recommended for easy installation.

2. Loosen the quick connects in clockwise directions and detach the quick connects in the fixture body and J-box
   

3. Pick up the cover of the driver box as shown below. remove one of the knock out holes on the side of the electrical box (B), based on the installation position. feed the power cord (not included) and all the electrical connection wires through the open knockout hole in the electrical box and tighten the power cord securely.
   

4. feed the wires from the electrical source through the open knock out hole in the electrical box (B). Insert the hot, neutral wires from the electrical source into the wire connectors of the black and white wires in the electrical box (B). Insert the ground wire from the electrical source into the wire connectors of the green wire in the electrical box (B). close the electrical box cover.

5. Place the electrical box (B) through the cut-out hole in the ceiling and position it where desired.
   NOTE: The electrical box (B) must be no more than 16 inches from the edgelit downlight based on the length of the connector cables.
   

6. Align the male connector from the electrical box (B) into the female connector from the LED downlight (A). Twist the quick connects in counterclockwise direction and lock the quick connects in the fixture body and junction box.
   

7. one at a time, flip the spring clips on the LED downlight (A) up and insert into the opening in the ceiling. once both spring clips are inside the cut-out, gently push the LED downlight (A) upward until the trim is flush with the ceiling surface.
   NOTE: select the preferred color temperature of the light before inserting the LED downlight (A) into the ceiling opening.

8. Restore power at the electrical panel.
   Turn on the light switch to activate the fixture.
   

9. This downlight allows you to customize the color of the trim: white trim and Black trim (D). hold both sides of the lamp, and remove the white trim as shown below.
   NOTE: The product is shipped with the white trim installed on the downlight.
   

ADJUSTING THE COLOR TEMPERATURE OF THE LIGHT
This LED downlight allows you to customize the color temperature of the light using five settings from Warm White to Daylight.

1. choose your favorite correlated color temperature (ccT) from five options: 2700K Warm White, 3000K Soft White, 3500K Cool White, 4000K Bright White, or 5000K Daylight.
2. Move the toggle switch on the fixture body (A) to make your selection before inserting into bracket or ceiling.
   NOTE: The factory setting for the correlated color temperature (ccT) is 2700K, which is the warmest white light.

SELECTING DOWNLIGHT Or NIGHTLIGHT MODE
The product can be used in one of two modes: downlight mode, which provides full brightness and allows selection from five color temperatures, or nightlight mode.
nighlight mode provides reduced light output at 2000K Amber color temperature for very soft illumination at night.
To TUrn on ThE MAIn LIghT

1. Turn on the light switch to activate the light fixture.

To chAngE To nIghTLIghT MoDE wITh rEDUcED LIghT oUTPUT froM ThE TrIM

1. switch the downlight off and back on again within 3 seconds to activate nightlight mode.
   NOTE: The main downlight will not provide light output when the nightlight trim is illuminated.

To rETUrn To DownLIghT MoDE wITh fULL LIghT oUTPUT whEn In nIghTLIghT MoDE

1. switch the downlight off and back on again to activate the downlight mode.

LIgHT DISTrIbuTION
Item # 1000000000 /Model # 538661010Maximum Candela = 196.804
Located At Horizontal Angle = 0, Vertical Angle = 0

1 – Vertical Plane Through Horizontal Angles (0-180)

2 – Vertical Plane Through Horizontal Angles (90-270)

Item # 1000000000 /Model # 538671010 Maximum Candela = 196.804
Located At Horizontal Angle = 0, Vertical Angle = 0

1 – Vertical Plane Through Horizontal Angles (0-180)

2 – Vertical Plane Through Horizontal Angles (90-270)

CARE AND CLEANING

CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the breaker off or removing the fuse from the fuse box. clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.

TROUBLESHOOTING

Minor problems often can be fixed without the help of an electrician.
WARNING: Before doing any work on the fixture, disconnect power to the light fixture.

Contact a qualified electrician.
There is a defective switch.| Contact a qualified electrician.
The fuse blows or the circuit breaker trips
When the light is turned on.| The wires are crossed or the power wire is grounding out.| Check the wire connections. Contact a qualified electrician or call customer service 1-877-527-0313.
The light fixture flickers or makes a buzzing
sound.| The dimmer circuit is not compatible with the product.
The dimming circuit is set outside the dimming range of the product.| Check the product page at www.HomeDepot.com for a list of compatible dimmers.
Turn or slide the dimmer switch to adjust the light output until the flickering or buzzing stops.
Out of sync| Slide the dimmer too fast.| Turn off the wall switch for more than 3 seconds, then turn back on.
The dimmer circuit is not compatible with the product.| Check the product page at www.HomeDepot.com for a list of compatible dimmers.

WARNING: carefully read and understand the information given in this manual before beginning the assembly and installation.
failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal.

• Risk of fire or electric shock. Installation of this LED retrofit Kit assembly requires a person familiar with the construction and operation of the light fixture’s/luminaire’s electrical system and the hazard involved. If not qualified, do not attempt installation. contact a qualified electrician.
• changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

NOTICE: noT for EMErgEncY LIghTIng.
NOTICE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the fcc rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: reorient or relocate the receiving antenna, increase the separation between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the receiver is connected, and consult the dealer or an experienced radio/TV technician for help. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARRANTY

WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of five (5) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in anyway not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor / expense costs involved in the replacement or repair of said product.
contact the customer service Team at 1-877-527-0313 or visit www.homeDepot.com.

Questions, problems, missing parts? Before returning to the store,
call commercial Electric customer service
8 a.m. – 7 p.m., EsT, Monday – friday
9 a.m. – 6 p.m., EsT, saturday
1-877-527-0313
HOMEDEPOT.COM
retain this manual for future use.

References

• The Home Depot
• The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>