LNC A05069H5 Labradorite 5 Light Gold with Linear LED Hanging Kitchen Island Light Instruction Manual

LNC A05069H5 Labradorite 5 Light Gold with Linear LED Hanging Kitchen

Island Light

PRODUCT INFORMATION

Item Number: A05069H5

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per blub.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED

(NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

• (C) Mounting plate (1)
• (D) Stud (4)
• (E) Canopy (1)
• (F) Loop (4)
• (G) Quick link (2)
• (H) Tube
• (I) Body (1)
• (J) Cover (5)

ACCESSORIES & QTY ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (K) Crystal hook (10) (spare part)
• (L) Crystal (1) (spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation

Step A1 »

1. Carefully pass the fixture wires through one side of the loop (F) and tubes (H).
2. Screw tubes (H) onto the body (I) as shown in the illustration.

Step A2 »

• Attach quick links (G) to loops (F) on the canopy (E) and on the top of upper tubes (H).

Turn off power

Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

• Go to the main fuse, or circuit breaker, box in your home.
  • Place the main power switch in the “OFF” position.
• Place the wall switch in the “OFF” position.

Make installation

• Step B1 »
  Unscrew studs (D) from canopy (E) and then remove mounting plate (C).

• Step B2 »
  Attach mounting plate (C) to the outlet box with mounting

• Step B3 »
  If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the mounting plate (C) is at least 6″.

• Step B4 »
  Make wire connections

Connect wires as below wires connection shown below.

PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

Connect wires according to the chart below

Note : When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)

1. Twist wires together with plastic wire connectors until tightly joined.
2. Wrap each connector with approved electrical tape.
3. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step B5 »
  Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening studs (D) onto the preassembled screws in mounting plate (C).

• Step B6 »

1. Hang crystal hooks (K) into holes of covers (J) to hang up crystals (L) as shown in the illustration.
2. Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check everything is already installed properly, then you can turn on the light. Enjoy!

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING

1. To clean, wipe the fixture with a soft cloth.
2. Clean glass with a mild cleaner (such as mild and non-abrasive soap).
3. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>