OPT7 B00TT7RWYC Underbody 8pc w Unlock Light Installation Guide
- June 15, 2024
- OPT7
Table of Contents
OPT7 B00TT7RWYC Underbody 8pc w Unlock Light
MAIN COMPONENTS
RIGID LIGHT BARS 18”×4 & 24”×4
AURA CONTROL BOX
HARDWIRE POWER HARNESS
HAND HELD REMOTE
MOUNTING KIT
INCLUDES –
WIRE MOUNTS, SELF-TAPPING SCREWS, BOOSTER, VELCRO, ZIP TIES
INSTALLATION
STEP 1
Decide where to locate the control box and ensure wiring has enough length
for light bars to be installed in desired location.
IMPORTANT:
The control box must be installed inside the vehicle as it is not waterproof.
Avoid installation areas of the engine bay + heated surfaces.
As shown below, connect all the LED bars to the control box with the included extension cables.
IMPORTANT:
The extension wires are on the led bar. Lay out the bars to measure the length
prior to install for a successful installation.
4 × 24” LED Bar + 8ft extension wire
2 × 18” LED Bar + 18ft extension wire
2 × 18” LED Bar + 8ft extension wire
HOW TO CONNECT POWER HARNESS TO YOUR VEHICLE
- Connect the Red line(+) of power hareness to the vehicle battery’s positive terminal.
- Connect the Black line (-) of power hareness to the vehicle battery’s negative terminal or an unpainted area on your vehicle’s frame.
WARNING
- Connecting to more than 10 AMP will override the kit and cause early failure, ensure it is 10AMPs or less!!
- Please ensure that the LED bars or strips/control box/wiring all are mounted in areas where will not exceed 85℃ or 185℉.
STEP 2
Secure Control box in desired location with Velcro or zip ties.
- CONTROL BOX NOT WATERPROOF Ensure the control box is safely and securely hidden from exposing elements of moisture.
STEP 3
Secure the light bars using the zip ties to tie all the wiring away from the
moving components.
* IMPORTANT:
The LED connectors are not waterproof. You will need to use HEAT SHRINK TUBE
(not included) or ELECTRICAL TAPE around the LED connectors to ensure the
longevity of the lighting kit.
STEP 4
Using the included E-Z Remote, select your desired color or pattern.
AUX WIRING FOR A DOOR/DOME LIGHT
Please scan to see a detail instruction on Door Assist Sync or go to
https://wintis.ladesk.com/549690-AURA-Door-AssistAUX-Installation-Guide
CONTROL WIRE FOR A DOOR UNLOCK LIGHT
Please make sure the control wire (wire with the yellow sticker) is connected to an “ACC/On” power source (SEE METHOD 1 FOR DETAILS); otherwise, when unlocking it with the car keyfob, it will not trigger any light effects!!
NOTE: When remote unlock feedback is enabled, it will glow blue for 15 seconds.
INSTALLATION INSTRUCTIONS
METHOD : 1
STEP 1
Open the driver’s door. Then find the door access system control harness that
connects between the door frame and the door.
STEP 2
Pull off the harness cover and find the trigger wire that activates the door
lock/unlock.
IMPORTANT
HOW TO DIAGNOSE THE CORRECT TRIGGER WIRE?
First, you must prepare a multimeter. Next, please press the “Lock/Unlock”
button on the car key fob to find out this signal source, this measurement
process may take you a little time, but it will ensure that you find the
correct signal you need.
STEP 3
Connect the control wire (red) to the trigger wire. Then connect the light bar
to the control box and use the car key fob for a final test.
METHOD : 2
STEP 1
Confirm if the DRL is still on after unlock the vehicle .
STEP 2
Confirm if the DRL is halogen lamp .
IMPORTANT
DRL has to be an independent signal, it cannot be a shared signal with fog
light, high beam, parking light or turn light.
STEP 3
Open the engine room and find the positive wire of the DRL .
IMPORTANT
HOW TO DIAGNOSE THE CORRECT POSITIVE WIRE OF DRL ?
First, please prepare a multimeter.
Next, press the “Lock/Unlock” button on the key fob to find the signal source,
then find out the positive wire .
STEP 4
Connect the trigger wire (red) that is on the control box to the DRL positive
wire, then connect the LED strip to test if it works .
DISCLAIMER
OPT7 Lighting is not liable for damages or personal injuries while installing
this product. The Installation Guide is intended as assistance to reduce setup
time.
OPT7 Lighting assumes no responsibility for improper installation.
If you are unfamiliar with your vehicle or inexperienced with aftermarket
upgrades, please seek professional assistance.
OPT7 recommends installation for safety and guidance.
Modified installations or installation recommendations not specified by OPT7
Lighting will void product warranty.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>