SSV WORKS 230-RG4-SWE12 Ranger Alpha12 Switcher Box Mounting Kit Instruction Manual
- September 4, 2024
- SSV WORKS
Table of Contents
SSV WORKS 230-RG4-SWE12 Ranger Alpha12 Switcher Box Mounting Kit
Specifications
- Product Name: Switcher Box Mounting Kit
- Model Number: 230-RG4-SWE12
- Compatible with: 2018-Up Polaris Ranger Alpha12
- Manufacturer: SSV Works
- Warranty: Limited 1-year warranty against defects in material or workmanship
Product Usage Instructions
- Attach the RAM Mount ball adapter to the Controller Mounting bracket using the 1 3/8 pan head screw and locknut.
- Attach the Controller Mounting Bracket to the 15-Button Controller using the (4) 4-40×0.75 Thread cutting screws.
- Insert the 15-button Touch screen with the RAM Mount ball and the RAM Mount base to the Double Socket Arm and tighten the T-knob.
- Place the Ranger RAM Mount mounting plate in the dash pocket and drill (4) holes for the push rivets using a 5/16 drill bit. Mark drill holes on the 4 corner holes.
- Drill a 5/8 hole in the middle of the dash pocket for the controller cable.
- Insert the 15-button controller cable through the middle hole in the dash pocket.
- Use (4) push-in rivets to secure the Ranger RAM Mount mounting plate to the dash pocket.
- Mount the 15-button with RAM Mount to the mounting plate using (4) M5x16mm Pan-Head screws included in the ALPHA12 kit.
- Mount the ALPHA12 Brain module to the Ranger brain module bracket using (4) M5x10mm Phillips screws and washers.
- Use the (4) #12×0.75 self-tapping Phillips screws included in the kit to secure the Ranger brain bracket to the firewall below the busbar. Line up the bracket holes to the pre-existing screw bosses.
- Run the power and ground wires from the ALPHA12 kit to the battery location. Battery is located under the front passenger seat on 2-door models and under the rear passenger seat in 4-door models.
FAQ
- Q: What is covered under the warranty for SSV Works products?
- A: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are covered by a limited 1-year warranty against defects in material or workmanship. Labor for the replacement of defective components is not covered. Contact SSV Works for further warranty information.
WARRANTY INFORMATION
- All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship.
- All SSV Works Electronics are covered by a limited 1-year warranty against defects in material or workmanship.
- Labor for the replacement of defective components is not covered.
- Contact SSV Works for further warranty information.
Please read and understand these instructions completely before installation to avoid possible injury or damage to the accessory or vehicle.
PARTS CONTENTS
WARRANTY INFORMATION
All SSV Works enclosures are covered by a limited lifetime warranty against
defects in material or workmanship. All SSV Works Electronics are covered by a
limited 1-year warranty against defects in material or workmanship. Labor for
the replacement of defective components is not covered. Contact SSV Works for
further warranty information.
Please read and understand these instructions completely before installation to avoid possible injury, or damage to the accessory or vehicle.
TOOLS NEEDED FOR INSTALLATION
- Phillips Screw Driver
- 13mm wrench
NOTE: The RAM mounting ball, Controller Mounting Bracket, and mounting hardware are included in the ALPHA12 Kit.
Installation Instructions
CONTROLLER RAM MOUNT ASSEMBLY
- A. Attach the RAM Mount ball adapter to the Controller Mounting bracket using the 1 3/8” pan head screw and locknut.
- B. Attach the Controller Mounting Bracket to the 15-Button Controller using the (4) 4-40×0.75 Thread cutting screws.
- C. Insert the 15-button Touch screen with the RAM Mount ball and the RAM Mount base to the Double Socket Arm and tighten the T-knob.
TOOLS NEEDED FOR INSTALLATION
- Phillips Screw Driver
- 5/8” and 5/16” Drill Bit
- Drill
SWITCH Works 15-Button Controller Installation
- A. Place the Ranger RAM Mount mounting plate in the dash pocket and mark drill holes on the 4 corner holes.
- B. Drill (4) holes for the push rivets using a 5/16” holes drill bit.
- C. Drill a 5/8” hole in the middle of the dash pocket for the controller cable.
- D. Insert the 15-button controller cable through the middle hole in the dash pocket.
- E. Use (4) push-in rivets to secure the Ranger RAM Mount mounting plate to the dash pocket.
- F. Mount the 15-button with RAM Mount to the mounting plate using (4) M5x16mm Pan-Head screws (B-S2708) included in the ALPHA12 kit.
TOOLS NEEDED FOR INSTALLATION
- Phillips Screw Driver
- 13mm Socket Wrench
SWITCH Works Brain Module Installation
- A. Mount the ALPHA12 Brain module to the Ranger brain module bracket [B-A3293] using (4) M5x10mm Phillips screws [B-S1158] and washers.
- B. Use the (4) #12×0.75” self-tapping Phillips screws [B-HP3300], included in the kit, to secure the Ranger brain bracket to the firewall below the busbar. Line up the bracket holes to the pre-existing screw bosses.
- C. Run the power and ground wires from the ALPHA12 kit to the battery location. Battery is located under the front passenger seat on 2-door models and under the rear passenger seat in 4 door models.
- D. Connect the accessories to the High and Low current harnesses and plug the harnesses to the brain module. NOTE that the 15-button controller MUST be plugged into the module before connecting the power and ground cables to the battery. Snap-on the terminal cover to the module’s + terminal.
- E. Refer to the SW-E12 instructions manual for a detailed installation and programming procedure of the SWITCH Works Alpha12.
THIS CONCLUDES THE INSTALLATION PROCESS. QUESTIONS? PLEASE CONTACT SSV WORKS AT 818-991-1778 OR EMAIL SUPPORT@SSVWORKS.COM
CONTACT
SWITCH Works is a product by SSV Works. We are committed to your satisfaction and we know you will enjoy our products. If you have questions or need any assistance, please let us know.
- SSVWORKS.COM
- 1-818-991-1778 EXT 2
- SUPPORT@SSVWORKS.COM
- SSV WORKS, 201 N. Rice Ave Unit A, Oxnard, CA 93030
- www.SSVworks.com | Phone: 818-991-1778 | Fax: 866-293-6751
Returns must be made within 30 days of the purchase date. Claims for missing items or items damaged in transit must be received within five business days of receipt of merchandise. All returns must be in original packaging and in re-sellable condition. Shipping fees are not refundable.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>