LNC A05065 Elynamina Matte Black Modern Contemporary Geometric LED Instruction Manual

June 15, 2024
LNC

LNC logo A05065 Elynamina Matte Black
Modern Contemporary Geometric LED
Instruction Manual

A05065 Elynamina Matte Black Modern Contemporary Geometric LED

Item Number: A05065

WARNING (To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.

  2. Please read the instruction carefully and save it as you may need it at a later time.

  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
    » Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
    » Place the wall switch in the “OFF” position.

  4.  Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gap between the mounting surface and canopy exceeding 3/16” should be corrected as required.

  5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

  6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 12W.

  7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

  8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

  9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

LNC A05065 Elynamina Matte Black Modern Contemporary Geometric LED -
IMAGE

TOOLS REQUIRED (NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

LNC A05065 Elynamina Matte Black Modern Contemporary Geometric LED -
TOOLS

PARTS TYPE & QTY INCLUDED:
(A) Mounting plate (1)
(B) Green ground screw (1)
(E) Screw (2)
(F) Canopy (1)
(G) Lock nut (2)
(H) Cable (1)
(I) Steel Wire (1)
(J) Tube (1)
(K) Connector (1)
(L) Body (1)LNC A05065 Elynamina Matte Black Modern Contemporary Geometric
LED - PARTS TYPE

ACCESSORIES & QTY ENCLOSED:
(C) Plastic wire connector (3)
(D) Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS:

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

  2. Turn off power
    Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
    » Go to the main fuse, or circuit breaker, box in your home.
    Place the main power switch in the “OFF” position.
    » Place the wall switch in the “OFF” position.

  3. » ● Unscrew screws (E) from canopy (F).
    ● Remove mounting plate (A).

  4. Screw tube (J) onto connector (K) as shown in the illustration.

  5. Attach mounting plate (A) to the outlet box with mounting screws (D).

  6. Make wire connections
    Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
    Connect ground wires according to the chart belowLNC A05065 Elynamina Matte
Black Modern Contemporary Geometric LED - chart belowConnect wires according to the chart below

Connect Black or
Red Supply Wire to:| Connect
White Supply Wire to:
---|---
Black| White
Parallel cord (round & smooth)| Parallel cord (square & ridged)
Clear, Brown, Gold or Black without tracer| Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with copper conductor| Insulated wire(other than green) with silver conductor

  • Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.) • Twist wires together with plastic wire connectors until tightly joined.
    • Wrap each connector with approved electrical tape.
    • Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

    1. Raise canopy (F) to the ceiling and secure canopy (F) in place by tightening screws (E) onto the pre-assembled screws in mounting plate (A). Note: canopy (F) should be snug against the ceiling and screws (E).
      If not, adjust the threaded length on mounting plate (A):
      • Unscrew the pre-assembled hex nuts.
      • Screw the pre-assembled screws in or out of mounting plate (A).
      • When the secure length is achieved, tighten the hex nuts and back to step 7.

    2. To adjust the hanging height of the fixture:
      ● Press down and hold lock nuts (G) by hand.
      ● Pull or push steel wire (I) and cable (H) in and out of canopy (F) to increase or decrease the hanging height.
      • Please adjust steel wire (I) first.LNC A05065 Elynamina Matte Black Modern
Contemporary Geometric LED - chart below1

    3. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture cane ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

LNC logo ****+1 8638672245
service@lnchome.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals