ROSIERES RVG2216TG Built-in Gas Cooking Range User Manual

RVG2216TG Built-in Gas Cooking Range
User Manual

RVG2216TG Built-in Gas Cooking Range

RVG2216TG RVG2238TG
Built-In Gas Cooking Range

Please read these instructions and warranty information carefully before use and keep them handy for future reference.

ATTENTION!
According to the Gas Safety Ordinance of Hong Kong, any gas installation works including the installation of appliances and connection tubing, must be undertaken by registered gas installers who are registered for that appropriate  classes and be employed by registered gas contractors.
A. LPG Connection
– Tubing connection: please use approved flexible tubing bearing EMSD approval marking (eg.”EMSD APPROVAL GTXXXX”) accessories  and gas cock for connecting from back of the unit to the gas supply point.
– Stainless steel braided flexible hose connection:
Please use approved stainless steel braided flexible tubing bearing EMSD approval marking (eg. “EMSD APPROVAL GTXXXX”) accessories and gas cock for connecting from½ inch B.S.P at back of the unit to the gas supply point.
B. Town Gas Connection
Please use approved stainless steel braided flexible tubing bearing EMSD approval marking (eg. “EMSD APPROVAL GTXXXX”) gas cock for connecting from½ inch B.S.P at back of the unit to the gas supply point.

Notice Before Use

15. Contact the service department of the authorized agent for repair and parts replacement. During guarantee period, Gilman Group Ltd. will reserve the right to change for spare parts and service fees if the damage is caused by mi use or improper installation.
16. When installing built-in gas hob on top of stove cabinet, please check that there is provision for ventilation at the cabinet to ensure proper operation of the gas hob.
17. Do not store any flammable materials, sprays or pressurized containers inside the stove cabinet.
18. The panel of this built-in hob is made of tempered glass which is safer than normal glass for this application. However, the following safety precautions for using built-in hob with glass top panel should also be noted in order to prevent the glass top panel from breaking:
I . Clean the burner assembly frequently to maintain a clear gas passage on the flame distributor. Clean and tidy up the flame distributor after spillage of food and liquid  once the burner assembly cooled down.
II. Turn off the gas appliance immediately if abnormal noise propagates from the gas appliance and contact gas supply company or gas hob importer for inspection.
III. Do not use oversized utensils for cooking, utensil size should be less than 34cm.
IV. Do not impact the glass surface with hard  objects or place heavy objects on the glass surface.

Product Structure

This figure is made for reference purpose only. Please refer to actual component parts.

Installation Instructions

Attention
The gas cooking range must be installed by registered gas installers. Otherwise, Gilman Group Ltd. Will not be responsible for any damages.
– The use of a gas cooking appliance produces heat and moisture, so it is essential to ensure that the kitchen is well ventilated. Keep natural ventilation windows open or install a mechanical ventilation device(mechanical extractor hood). Prolonged intensive use of the appliance may call for additional ventilation, for example opening windows or increasing the level of mechanical ventilation where present.
– Install the built-in hob in a well ventilated room and keep it away from any combustible or inflammable objects such as paper or oil.
– Place the built-in hob on a stable and level surface.
– If the unit is to be installed close to combustible surroundings(such as wooden walls, wooden shelves), it should be installed at least 15cm(6″) from the side walls, the unit should be installed with a distance of at least 15cm away from
surrounding combustible materials.
– Distance from bottom more than 25mm(1″).
– External gas governor not required.

1. Room Ventilation
   Give the kitchen the amount of air required for regular gas combustion and for the room to keep well-ventilated-the volume of which must not be less than 20m3. Air must naturally flow through permanent opening in the walls of the room. These openings must vent the fumes outdoors and their section must be at least 100cm2, and ensure that they may never be blocked.

2. Gas Connection
   Before connecting the appliance, check that the specifications on the data label affixed to the underside of the hob correspond to those of the gas and electricity mains in the house. A label on the appliance indicates the regulating conditions: Type of gas and working pressure. Gas connection must comply with the pertinent standards and provisions in force. The size of the gas inlet is 1/2 inch.Model No.| A| B
   ---|---|---
   RVG2216TG
   RVG2238TG| 265| 490

3. Cut-out Dimensions

4. Correct Position of Burner Rack & Burner Cap Make sure that the following parts are fitted properly before use.
   1.Burner Rack
   Fit Burner Rack legs into Drip Pan(Fig.1). Please do not tilt the placement, otherwise it will affect the fire is not normal.2.Burner Cap
   Fit burner cap into burner head base(Fig.2), properly without gap(Fig.3).If incorrect placement for both of them, it will result in the burn out of burner head and blasting of glass. If incorrect placement for both of them, it may
   cause out of shape and increase the risk of releasing carbon monoxide(CO).

Operating Instructions

Attention
All cooking ranges must be installed, connected and commissioned by registered gas installers. Do not install or repair the cooking range yourself.
Do not use additional fitting, such as aluminium foil.
Do not clean the top of the sensor with a hard brush, as it may damage the sensor.

1. While pushing the control knob, turn it to the left (towards the “ON” position) slowly until you hear a “click” sound. Electronic spark will ignite burners. Release your hand after confirm the burners is ignited. The hob has automatic continuous ignition function, do not need to continue to push the control knob after ignition. “Click” sound and spark will be stopped automatically after 6-8 seconds.
2. If the flame goes out when you release your hand, repeat the ignition procedure again but try release your hand slowly.
3. Turn control knob to adjust flame to desirable setting.
4. Flame can be adjusted between” ” and” “. Please adjust flame slowly(Fig.4&Fig.5).
5. If the flame is extinguished while using, the safety dev ice will shut the gas off after a short delay. When this happens, please turn the knob to “ ” position.
6. Turn the ignition control knob backwards to the “ ” position to extinguish the burner.

How to handle safety device and change battery

• If the flame is extinguished during operation, the automatic flame failure safety device will shut off gas after a short delay. Turn the knob to” ” position when this happens.

• The safety sensor is very delicate-please do not use hard brushes or rough cleaning pads when cleaning.

•  Aeration is preset at factory, please do not attempt to adjust it.
  Battery box is located at bottom(DC1.5VX1). Open the door of battery box and change battery.

• Set battery at correctly polarity(“+” and”-“).

care & Maintenance

Attention
Do not clean the unit when it is hot.

1. Wipe the glass panel with a soft, damp cloth and mild detergent.
2. Wash the burner racks and burner heads in warm water and detergent.

Troubleshooting

supply
Air exist in the gas tubing| Prolong ignition time and repeatedly ignite till air goes out
Gas hose bends| Straighten it
Injector clogged| Get rid of the blockage by a pin(carry out by the RGI)
Ignition plug has soot or in wrong position| Clear or adjust the position(carry out by the RGI)
Flame holes of Burner cap are blocked by water or filth| Cleaning
Terrible smell| Gas tubing aged| Change with a new gas tubing(carry out by the RGI)
Main fire of burner not lighted| Re-ignite after the gas dispersed
Valve not well-sealed| Change with a new valve(carry out by the RGI)
Weak flame| Gas pressure too low| Check gas supply or whether gas regulator is clogged(carry out by the RGI)
Ports of burner cap clogged| Clean ports

Technical specifications

Model No.:
Serial No.:
Dealer:
Date of Purchase:
Invoice No.:
The product specifications may be changed without prior notice.
Please contact customer service for details if necessary.
If there is any inconsistency or ambiguity between the English version and the Chinese version, the English version shall prevail.
Warranty Registration
Register your product online

www.dchtoolbox.com

Tool Box Customer Service Centre
4/F, DCH Building, 20 Kai Cheung Road, Kowloon Bay, Hong Kong
Customer Service Hotline: (852) 8210 8210
E-mail: 8210service@gilman-group.com
ARs www.gilman-group.comGilman Group Limited
7/F DCH Building 20 Kai Cheung
Road, Kowloon Bay Kowloon

852 2418 3272

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>