ROSIERES 14853TH-UK 5KG Dry 1400rpm Built-in Inverter Washer Dryer Instruction Manual
- June 4, 2024
- ROSIERES
Table of Contents
ROSIERES 14853TH-UK 5KG Dry 1400rpm Built-in Inverter Washer Dryer
INSTALLATION
- Release the power chord and drain hose from the securing clip at the rear of the machine.
- Remove the 2 or 4 transportation screws (A) on the back and remove the 2 or 4 flat washers, rubber bungs and plastic spacer tubes (B) as illustrated in figure 1.
- If the washing machine is built-in, unscrew the 3 or 4 transportation screws (A) and remove the 3 or 4 flat washers, rubber bungs and plastic spacer tubes (B).
- During the removal of the screws occasionally spacer tubes fall inside the product, these can be remove by tilting the product forward and recovering them from the floor or inside the base of the machine.
- Cover the open transportation screw holes with the 2 or 4 plastic caps included in the instruction bag.
WARNING keep packaging materials away from children.
Place the corrugated plastic sheet, found on top of the appliance during the
unpacking process, into the base of the appliance as shown in figure 2
(according to the model, consider version A, B or C).
Instructions for mounting the furniture door
Position the template onto the reverse of the furniture door. It is possible
to mount the hinges and closure magnet on the right or left-hand side
depending on your requirements. Mark the screw hole positions, then drill out
these positions.
- Fix the hinges in place with the 4 screws provided (A).
- Fix the magnet (B) in place using screw (C).
- Mount the plate (D) on the right or left-hand side, depending on your installation requirements. Place the plastic support (E) under the plate and fix it in position with screw (F).
- Snap mount cap (G) in the lower position.
- Mount the furniture door to the front of the washer using the hinges. Place the spacers under the hinges (I) and then fix in position with screw (H).
We suggest mounting the furniture door so that it opens towards the left, which is the same direction as the porthole door. This will leave more space when you are loading washing into the appliance.
- Slide the washer into an opening of the size indicated in the diagram opposite. A furniture plinth may be run across the front of the appliance, but its height will be dictated by the height the washer is set at.
- The 4 adjustable feet allow the height of the washer to be adjusted from 820 mm to a maximum of 840 mm. To adjust the height, you should remove the nuts fitted to each foot and replace these with the 5 mm nuts supplied. Raise the feet to your desired height and then fully tighten the lock nut to the base of the washer.
Hydraulic connections
- Connect the water hose to the water supply tap only using the hose supplied with the appliance (do not reuse old hose-sets).
- SOME MODELS may include one or more of the following features:
- HOT &COLD: water mains connection settings with hot and cold water for higher energy savings. Connect the grey tube to the cold water tap and the red one to the hot water tap. The machine can be connected to the cold water tap only: in this case, some programs may start a few minutes later.
- aqua stop : a device located on the supply tube that stops water flow if the tube deteriorates; in this case, a red mark will appear in the window “A” and the tube must be replaced. To unscrew the nut, press the one-way lock device “B”.
- AQUA PROTECT – SUPPLY TUBE WITH GUARD :
Should water leak from the primary internal tube “A”, the transparent containment sheath “B” will contain water to permit the washing cycle to complete. At the end of the cycle, contact the Customer Service Centre to replace the supply tube.
Setting
- The washing machine should be installed in its final position such that the water fill hose is not kinked or trapped. The corrugated drain hose should be inserted into suitable drain pipe of between 50 cm and 85 cm height above the floor using the curved drain hose support. If an under sink connection is used the drain hose must be routed above the sink overfill opening to prevent back siphoning. Care must be taken to avoid kinking or trapping the drain hose .
- Level the appliance using the feet as illustrated in :
- turn the nut clockwise to release the screw;
- rotate the foot to raise or lower it until it touches to the floor;
- lock the foot, screwing in the nut, until it tightens against to the bottom of the washing machine.
- Plug in the appliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>