LNC A05159 Butterscouch 5-Light Matte Black and Geometric LED Hanging Pendant Light Instruction Manual

: June 15, 2024
: LNC

Table of Contents

LNC A05159 Butterscouch 5-Light Matte Black and Geometric LED Hanging
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LNC A05159 Butterscouch 5-Light Matte Black and Geometric LED Hanging

Pendant Light Instruction Manual

+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST

homecustomercare@outlook.com

Item Number: A05159

WARNING (To reduce the risk of fire, electric shock, or personal injury):

. We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
  Place the main power switch in the “ OFF ” position.
- Place the wall switch in the “ OFF ” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per blub .
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED

(NOT INCLUDED):

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING

(C) Mounting plate (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Strain relief (1)
(G) Ball knob (2)
(H) Cable (1)
(I) Steel wire (2)
(K) Small mounting plate (1)
(M) Small canopy screw (2)
(N) Small canopy (1)
(O) Lock nut (2)
(P) Vertical frame (1)
(Q) Horizontal frame (1)
(R) Bottom frame (1)
(S) Screw (4)
(T) Plug (4)

ACCESSORIES & QTY ENCLOSED

(A) Plastic Wire Connector (3)
(B) Mounting screw (2)
(J) Anchor (2)
(L) Wood screw (2)
(U) Allen wrench (1)
(S) Screw (1) (spare part)
(T) Plug (1) (spare part)

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “ OFF ” position.
- Place the wall switch in the “ OFF ” position.
»
Unscrew ball knobs (G) from canopy (E) then gently remove mounting plate (C).
Unscrew ball small canopy screws (M) from small canopy (N) then gently remove small mounting plate (K).
»
Hang bottom frame (R) up.
Align side holes of bottom frame (R) and horizontal frame (Q), and then screw screws (S) into holes to secure them.
Insert plugs (T) into holes as shown in the illustration.
»
Hang vertical frame (P) to the unit.
Align side holes of bottom frame (R) and vertical frame (P), and then screw screws (S) into holes to secure them.
Insert plugs (T) into holes as shown in the illustration.
»
Carefully pass supply wires through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (B).
NOTE: To drill the holes in the wall for anchor (J), attach small mounting plate (K) to wall with wood screw (L) and mark the holes as shown in the illustration.

  *  _ **Please note that the central holes of mounting plate (C) and small mounting plate (K) are at both ends, with a distance of 523.5 mm between them.**_
  * Drill holes and gently knock anchor (J) into the holes until anchor (J) are level with the wall.
  * Secure small mounting plate (K) to the wall with wood screw (L).
  * Screw small canopy (N) to small mounting plate (K) as shown in the illustration.

NOTE: the side of mounting plate (C) marked “GND” must face out.

»
Make wire connections
Connect wires as below wires connection shown. REFER TO THE FOLLOWING CHARTS, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
- Twist wires together with plastic wire connector until tightly joined.
- Wrap each connector with approved electrical tape for a more secure connection.
- Carefully tuck all wires into the outlet box.
»
Fix canopy (E) to mounting plate (A) and secure with the previously removed ball knobs (G).
Fix small canopy (N) to small mounting plate (K) and secure with the previously removed small canopy screws (M).

Note: canopy (E) and small canopy (N) should be snug against the ceiling and ball knobs (G) and small canopy screws (M).
If not, adjust the threaded length of the preassembled mounting screws on mounting plate (C) and small mounting plate (K):

  *  _ **first, unscrew the pre-assembled hex nuts;**_
  *  _ **then, screw the pre-assembled mounting screws in or out of mounting plate (C);**_
  *  _ **when the secure length is achieved, tighten the pre-assembled hex nuts and back to step 8.**_

»
To adjust the hanging height of the fixture:

  * Press down and hold lock nuts (O) by hand.
  * Pull or push steel wires (I) in and out of canopy (E) and small canopy (N) to increase or decrease the hanging height.
2. To adjust the length of cable (H):
  * Use Allen wrench (U) to unscrew the screw in one of strain relief (F) as shown in the illustration.
  * Carefully pull and push cable (H), then tighten the screw till snug.
3. Check everything is already installed properly, then you could turn on the light. Enjoy!