LNC A05232 Lakierowane Matte Black and Polished Gold Cylinder Modern Instruction Manual

LNC A05232 Lakierowane Matte Black and Polished Gold Cylinder Modern

Item Number: A05232

WARNING
(To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. The mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides.
5. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
6. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
7. Make sure the voltage you are using is 120V. The maximum wattage is Type T, Max 60W per bulb.
8. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
9. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
10. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.
11. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture.

PARTS TYPE & QTY INCLUDED

• Mounting plate (1)
• Green ground screw (1)
• Сапору (1)
• Swivel joint (1)
• Knob nut (2)
• Tube
• The frame (1)
• Socket (1)
• Lampshade (1)
• Socket ring (1)

**ACCESSORIES & QTY ENCLOSED

**

• Plastic wire connector (3)
• Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power  Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
3. Go to the main fuse, or circuit breaker, box in your home.
4. Place the main power switch in the “OFF” position.
5. Place the wall switch in the “OFF” position.
6. Unscrew knob nuts (G) from the canopy (E).

Remove mounting plate (C).

1. According to your desired hanging height choose and use tubes (H).
2. Then pass the fixture wires through the chosen tubes (H), swivel joint (F) and canopy (E).
3. Be sure that all the threaded pipes are tightened, then screw the chosen tubes (H) onto the swivel joint (F) and the top of the frame (1).
4. Hand tighten till snug.
5. Attach mounting plate (C) to the outlet box with mounting screws (B).
6. Make wire connections

Connect wires as shown in the charts below.
PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below

Connect wires according to the chart below

• Twist wires together with plastic wire connector (A) until tightly joined.
• Wrap each connector with approved electrical tape for a more secure connection.
• Carefully tuck all wires into the outlet box.
• Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto the pre-assembled screws in the mounting plate (C).

Note: canopy (E) should be snug against the ceiling and knob nuts (G). If not, adjust the threaded length on the mounting plate (C)

• Unscrew the pre-assembled hex nuts.
• Screw the pre-assembled screws in or out of the mounting plate (C).
• When the secure length is achieved, tighten the hex nuts and back to step 7.
• Remove socket ring (L) from socket (J).
• Carefully place lampshade (K) onto socket (J), and then screw socket ring (L) to socket (J) to secure it.
• When installing the socket ring (L), please note the orientation of the socket ring (L) as shown in the illustration.
• Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
• Check that everything is installed properly, and then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wordina from illustration when orderina barts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders. steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>