LNC L67F7R2525439C Hairurin 6 Light Matte Black and Polished Gold Modern Instructions

: June 15, 2024
: LNC

Table of Contents

LNC L67F7R2525439C Hairurin 6 Light Matte Black and Polished Gold Modern
Product Information
Product Usage Instructions
IMAGE FOR FINISHED PRODUCT
PARTS TYPE & QTY INCLUDED
ASSEMBLY & INSTALLATION INSTRUCTIONS
ORDERING PARTS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LNC L67F7R2525439C Hairurin 6 Light Matte Black and Polished Gold Modern

Product Information

Specifications:

Item Number: A05254
Voltage: 120V
Maximum Wattage: Type A, Max 60W per bulb

Product Usage Instructions

Safety Precautions:

We strongly recommend installation by a licensed electrician.
Read the instruction manual carefully and save it for future reference.
Before starting any work, always shut off the electricity.
Ensure the mounting surface is clean, dry, flat, and strong enough to support the product.
The mounting surface should be 1/4 larger than the canopy on all sides.
If there are gaps exceeding 3/16 between the mounting surface and canopy, correct them as required.
Check if the ceiling or wall can withstand the weight of the lamp before installation.
Avoid exposing the lamp to acidic and alkaline substances as they may damage the surface.
When replacing bulbs, turn off or unplug the lamp and wait until it cools down as bulbs can get hot quickly.
Use common sense, caution, and care when working with electrical products.

Tools Required:

Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pliers
Wire Cutter/Stripper

Parts Included:

(C) Single bar x 1
(D) Green ground screw x 1
(E) Canopy x 1
(F) Lock nut x 3
(G) Strain relief x 1
(I) Cap nut x 1
(J) Cord x 1
(K) Steel wire x 3
(L) Socket ring x 6
(M) Lampshade x 6
(N) Socket x 6
(P) Insurance buckle x 3

Assembly & Installation Instructions:

Carefully remove the fixture from the carton and check that all parts and accessories are included.
Turn off power before starting the installation.
Press down and hold lock nuts (F) by hand.
Pull or push steel wires (K) in and out of canopy (E) to adjust the hanging height.
Adjust the length of cord (J) to achieve the desired height of the mounted fixture.
Use a screwdriver (O) to unscrew the screws in strain relief (G), and carefully pull and push cord (J) through canopy (E) and strain relief (G) to lengthen or shorten the cord.
Once the desired height is achieved, carefully tighten the screws till snug.
To adjust insurance buckles (P), use a screwdriver to loosen them and then pull them to the bottom of the canopy by hand.
Tighten insurance buckles (P) with a wrench to prevent the body from sliding off.
Connect the wires as shown in the provided charts. Note that the ground wire is a bare copper wire.

FAQ:

Q: Can I install the product myself?
A: While it is possible to install the product yourself, we strongly recommend hiring a licensed electrician for installation to ensure safety and proper installation.

Q: What is the maximum wattage for each bulb?
A: The maximum wattage per bulb is 60W for Type A bulbs.

Q: Can I use bulbs with higher wattage?
A: No, using bulbs with wattage higher than the specified maximum may result in damage to the product and can be a safety hazard.

Item Number: A05254

WARNING (To reduce the risk of fire, electric shock, or personal injury):

We suggest installation by a licensed electrician.
Please read the instruction carefully and save it as you may need it at a later time.
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
  Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

ACCESSORIES & QTY ENCLOSED:

(A) Plastic Wire Connector (3)
(B) Mounting screw (2)
(C) Single bar (1)
(D) Green ground screw (1)
(E) Canopy (1)
(F) Lock nut (3)
(G) Strain relief (1)
(1) Cap nut (1)
(J) Cord (1) |
(K) Steel wire (3)
(L) Socket ring (6) |
(M) Lampshade (6)
(N) Socket (6)
(0) Screwdriver (1)
(P) Insurance buckle (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
  Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
Unscrew cap nut (1) from single bar (C).
To adjust the hanging height of the fixture:
Press down and hold lock nuts (F) by hand.

  * Pull or push steel wires (K) in and out of canopy (E) to increase or decrease the hanging height.
2. Adjust the length of cord (J) to achieve the desired height of the mounted fixture.
  * Use screwdriver (O) to unscrew the screws in strain relief (G), carefully pull and push cord (J) through canopy (E) and strain relief (G) to lengthen or shorten the length of cord (J).
  * Once the desired height of fixture is achieved, carefully tighten the screws till snug.
3. After adjusting the height of the fixture, to adjust insurance buckles (P):
  * Use a screwdriver to loosen insurance buckles (P), and then pull insurance buckles (P) to the bottom of canopy by hand.
  * Tighten insurance buckles (P) with a wrench to prevent body from sliding off as shown in the illustration below.

Secure single bar (C) to the outlet box with mounting screws (B).
NOTE: the side of single bar (C) marked “GND” must face out.
Make wire connections
Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
Connect wires according to the chart below
- Twist wires together with plastic wire connector until tightly joined.
- Wrap each connector with approved electrical tape for a more secure connection,
- Carefully tuck all wires into the outlet box.
Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening cap nut (l) onto the preassembled threaded nipple on single bar (C).
NOTE: The canopy (E) should be snug against the ceiling with cap nut (1).
If not, adjust the threaded length of the pre- assembled threaded nipple on single bar (C):
- first, unscrew the pre-assembled hex nut;
- then, screw the pre-assembled threaded nipple in or out of single bar (C);
- when the secure length is achieved, tighten the pre-assembled hex nut and back to step 7.
Remove socket rings (L) from sockets (N).
- Hang lampshades (M) to sockets (N), and then screw socket rings (L) to sockets (N) to secure them.
- Install bulbs (Not included)
- (Please do not exceed the maximum wattage recommended on the socket.)
Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.