LNC Banswara 22.8 in 3 Light Polished Gold LED Modern Contemporary Vanity Light Bar Instructions

LNC Banswara 22.8 in 3 Light Polished Gold LED Modern Contemporary Vanity

Light Bar

Product Information

Specifications

• Item Number: A05265
• Maximum Wattage: Type T, Max 60W per bulb
• Voltage: 120V

Product Usage Instructions

Warning

To reduce the risk of fire, electric shock, or personal injury,please follow these precautions:

1. We suggest installation by a licensed electrician.
2. Read the instruction carefully and save it for future reference.
3. Before starting any work, always shut off the electricity.

Mounting Surface Preparation

The mounting surface should meet the following requirements:

• Clean, dry, and flat
• Strong enough to support the weight of the lamp
• 1/4 larger than the canopy on all sides
• Correct any gaps between the mounting surface and canopy exceeding 3/16 as required.

Lamp Installation

Please follow these steps to install the lamp:

1. Ensure that the ceiling or wall can stand the weight of the lamp before installation.
2. Turn off the power before starting the installation.
3. Secure the mounting plate (C) to the outlet box using the provided mounting screws (A).
4. Connect the wires according to the chart provided:
   • Connect the black or red supply wire to the outlet box ground using the green ground screw.
   • Connect the white supply wire to the fixture ground using the provided dimples and green ground screw.
5. Twist the wires together with the plastic wire connectors (B) until tightly joined.
6. Wrap each connector with approved electrical tape.
7. Ensure that no wire strands are exposed and carefully tuck all wires into the outlet box.
8. Proceed with further assembly and installation as instructed in the manual.

FAQ

Q: What tools do I need for assembly and installation?
A: You will need the following tools:

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Q: What is the maximum wattage for each bulb?
A: The maximum wattage per bulb is Type T, Max 60W.

Q: What voltage should I use?
A: The lamp is designed for use with 120V voltage.

Q: Can I replace the bulbs while the lamp is still powered on?
A: No, when replacing bulbs, you should turn off or unplug the lamp and wait until it is cool as bulbs get hot quickly.

Q: Are there any special precautions I need to take?
A: The lamp should be kept away from acidic and alkaline substances to avoid damaging the surface. Additionally, exercise common sense, caution, and care when using electrical products.

Item Number: A05265

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

4. Mounting surface should be clean, dry, flat, strong enough and 1/4* larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is Type T, Max 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDED

ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)
• (C) Mounting plate (1)
• (D) Green ground screw (1)
• (E) Back plate (1)
• (F) Knob nut (2)
• (G) Socket (3)
• (H) Lampshade (3)
• (I) Socket ring (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.

   • Go to the main fuse, or circuit breaker, box in your home.
     Place the main power switch in the “OFF” position.

   • Place the wall switch in the “OFF” position.

3. Make assembly
   Step A1
   Unscrew knob nuts (F) from back plate (E) and mounting plate (C), then set them aside for later installation.
   Step A2
   Carefully pass the supply wires from the outlet box through mounting plate (C).
   Secure mounting plate (C) to the outlet box with mounting screws (A).
   Step A3
   Make wire connections
   Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
   Connect ground wires according to the chart below
   Connect wires according to the chart below
   Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
   Step A4
   Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (C) with the previously removed knob nuts (F). Hand tighten until snug.
   NOTE: back plate (E) should be snug against the wall with knob nuts (F).
   If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):

   • Unscrew the pre-assembled hex nuts.
   • Screw the pre-assembled mounting screws in or out of mounting plate (C).
   • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
     Step A5

   1. Remove socket rings (I) from sockets (G).

   2. Carefully hang lampshades (H) onto sockets (G), and then screw socket rings (I) to sockets (G) to secure them.
      When installing socket rings (I), the orientation of socket rings (I) is that the side of rolled edge faces upward.

   3. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)

4. Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>