LNC A05249 Fagerlund 5-Light Matte Black and Polished Gold Modern/Contemporary Linear LED Instruction Manual

June 15, 2024
LNC

LNC A05249 Fagerlund 5-Light Matte Black and Polished Gold

Modern/Contemporary Linear LED

LNC-A05249-Fagerlund-5-Light-Matte-Black-and-Polished-Gold-Modern-
Contemporary-Linear-LED-product

Item Number: A05249

WARNING
(To reduce the risk of fire, electric shock, or personal injury):

  1. We suggest installation by a licensed electrician.
  2. Please read the instructions carefully and save them as you may need them at a later time.
  3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
  4. go to the main fuse, or circuit breaker, box in your home.
  5. Place the main power switch in the “OFF” position.
  6. Place the wall switch in the “OFF” position.
  7. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.
  8. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
  9. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
  10. Make sure the voltage you are using is 120V. The maximum wattage is Type T, Max 60W per bulb.
  11. Keep the lamp away from acidic and alkaline substances in case of damaging the lamp’s surface.
  12. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
  13. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur.
  14. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

TOOLS REQUIRED

(NOT INCLUDED)

LNC-A05249-Fagerlund-5-Light-Matte-Black-and-Polished-Gold-Modern-
Contemporary-Linear-LED-featured

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

LNC-A05249-Fagerlund-5-Light-Matte-Black-and-Polished-Gold-Modern-
Contemporary-Linear-LED-fig-3

  • Mounting plate(1)
  • Green ground screw (1)
  • Canopy (1)
  • Loop (4)
  • Quick link (2)
  • Ball nut (2)
  • Tube
  • Frame (1)
  • Socket (5)
  • Screw (15)
  • Lampshade (5)

ASSEMBLY & INSTALLATION INSTRUCTIONS

  1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
  2. Make pre-installation

ACCESSORIES & QTY ENCLOSED

  • Wire connector (3)
  • Mounting screw (2)
  • Screw (1) (spare part)

Step A1
Carefully pass the fixture wires through one side of tubes (I) and loops (F). Screw tubes (I) to the nipple of the frame (J).

Step A2
Open quick links (G). Attach quick links (G) to loops (F) on canopy (E) and on the top of tubes (I). Close quick links (G).

Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done. Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position. Place the wall switch in the “OFF” position.

Make installation

LNC-A05249-Fagerlund-5-Light-Matte-Black-and-Polished-Gold-Modern-
Contemporary-Linear-LED-fig-5

Step B1 » Unscrew ball nuts (H) from mounting plate (C).
Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
Note: the side of the mounting plate (C) marked “GND” must face out.
Step B3 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6*.
Step B4 » Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

LNC-A05249-Fagerlund-5-Light-Matte-Black-and-Polished-Gold-Modern-
Contemporary-Linear-LED-fig-6

  • Twist wires together with plastic wire connectors until tightly joined.

  • Wrap each connector with approved electrical tape and sure that no wire strands are exposed.

  • Carefully tuck all wires into the outlet box.

  • Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening ball nuts (H) onto pre-assembled screws on the mounting plate (C).
    NOTE: canopy (E) should be snug against the ceiling with ball nuts (H).

  • If not, remove canopy (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (C):

  • First, unscrew the pre-assembled hex nuts.

  • Then, screw the pre-assembled mounting screws in or out of the mounting plate (C).

  • When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step B5.

Step B6
Align holes of sockets (K) and holes of lampshades (M), and then screw screws (L) into holes to secure them as shown in the illustration. Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.) Check that everything is installed properly, and then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LNC User Manuals

Related Manuals