LNC A05208 6 Light Polished Gold Modern Contemporary LED Dry rated Chandelier Instruction Manual

LNC A05208 6 Light Polished Gold Modern Contemporary LED Dry rated

Chandelier

Item Number: A05208

WARNING
(To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instructions carefully and save them as you may need them at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done. Go to the main fuse, or circuit breaker, box in your home.
4. Place the main power switch in the “OFF” position.
5. Place the wall switch in the “OFF” position.
6. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides.
7. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
8. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
9. Make sure the voltage you are using is 120V. The maximum wattage is Type B, Max 40W per blub.
10. Keep the lamp away from acidic and alkaline substances in case of damaging the lamp’s surface.
11. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
12. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT

ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.

CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

TOOLS REQUIRED

Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDED

• Single bar (1)
• Green ground screw (1)
• Canopy (1)
• Collar ring (1)
• Collar loop (1)
• Quick link (2)
• Chain (1)
• Loop (1)
• Decorative column (1)
• Lid (1)
• Lampshade (6)
• Light tray (6)
• Arm (6)

ACCESSORIES & QTY ENCLOSED

• Wire connector (3)
• Mounting screw (2)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Make pre-installation

Step A1 » Adjust arms (0) to the proper position as shown in the illustration.

Step A2» Screw decorative column (K) onto the top of the lid (L) as shown in the illustration.
Step B1 » By measuring, determine the correct number of links needed for proper hanging height. Using the chain pliers, disconnect and discard the unwanted parts.
Step B2 » Attach quick links (H) to chain (I) and loop (J) on the top of the decorative column (K).
Step B3 » Carefully weave the fixture wires through the main chain (I) in and out of every other link and stop just when you reach the top of the chain (1). Gently pull the wires to ensure the wires are not stressed.

Turn off power

• Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
• Go to the main fuse, or circuit breaker, box in your home.
• Place the main power switch in the “OFF” position.
• Place the wall switch in the “OFF” position.

Make installation

Step C1 » Remove collar ring (F) from collar loop (G). Attach single bar (C) to the outlet box with mounting screws (B).

NOTE: the side of the single ban ( C) marked “GND ” must face out
Step C2 » Raise canopy (E) over collar loop (G) and screw collar ring (E) to measure a proper position. Unscrew collar ring (E) from collar loop (G) and remove canopy (E). Refer to the following note, you
will know the proper position where the collar loop (G) should be located.
NOTE: canopy (E) should be snug aga, not the ce should be screwed enough threads (no less than 6 threads) on the pre-assembled threaded nipple for more secure hanging. If not, adjust collar loop (G) on single bar (C) by screwing collar loop (G) in or out of the single bar (C) until the secure length is achieved
Step C3 » Pass chain (l) through collar ring (F) and then through canopy (E).
Step C4 » Open quick link (H), attach quick link (H) to collar loop (G). Close quick link (H). Pass the fixture wires through the collar loop (G) to the top of the pre-assembled threaded nipple and gently pull to ensure the wires are not stressed.
Step C5 » If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.
Step C6 » Make wire connections

Connect wires as shown in the charts below.

PLEASE NOTE THAT GROUND WIRE IS BARE COMPOSE WIDS NSVER CONNSET OTHSO WIDES TO CROIIND WIRES

• Twist wires together with plastic wire connectors (A) until tightly joined
• Wrap each connector with approved electrical tape.
• Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

Step C7 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening collar ring (F) onto collar loop (G).
Step C8 » 1) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.) Screw lampshades (M) onto light trays (N) as shown in the illustration. Check that everything is installed properly, and then you can turn on the light. We hope you enjoy your new lighting!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>