LNC A05100W Leawood 1 Light 13 in Sand Black Outdoor Wall Light Instructions

LNC A05100W Leawood 1 Light 13 in Sand Black Outdoor Wall Light

Product Information

Specifications

• Item Number: A05100W
• Voltage: 120V
• Maximum Wattage: Type A, Max 60W per bulb

Product Usage Instructions

Installation

To ensure safety and proper installation, please follow these instructions:

1. We recommend installation by a licensed electrician.
2. Read the instruction manual carefully and save it for future reference.
3. Before starting any work, always shut off the electricity.
4. The mounting surface should be clean, dry, flat, and strong enough to support the lamp. It should also be 1/4 larger than the canopy on all sides.
5. If there are any gaps between the mounting surface and canopy exceeding 3/16, they should be corrected as required.
6. Ensure that the ceiling or wall can handle the weight of the lamp before installation.
7. Make sure the voltage you are using is 120V. The maximum wattage per bulb is 60W.
8. Avoid exposing the lamp to acidic and alkaline substances as they can damage the surface.
9. When replacing bulbs, turn off or unplug the lamp and wait until it is cool as bulbs can get hot quickly.
10. These safety instructions do not cover all possible conditions, so please use common sense, caution, and care when working with electrical products.

Tools Required

Before starting assembly and installation, prepare the following tools (not included):

• Ladder
• Philips Head or Flat Blade Screwdriver
• Electrical Tape
• Pliers
• Wire Cutter/Stripper

Parts Included

The product includes the following parts:

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Gasket (2)
• (G) Screw (2)
• (H) Frame (1)
• (I) Glass sheet (4)

Accessories Enclosed

The product includes the following accessories:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

Assembly & Installation Instructions

1. Carefully remove the fixture from the carton and check that all parts and accessories are included.
2. Turn off the power before starting the installation.
3. Secure the mounting plate (D) to the outlet box with the mounting screws (A).
4. Connect wires as shown in the charts below. Note: Never connect other wires to ground wires.
5. Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Ensure no wire strands are exposed and carefully tuck all wires into the outlet box.

Wiring Connections

Connect wires according to the chart below:

WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.
2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home.
   • Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT ****

TOOLS REQUIRED (NOT INCLUDED)

Before starting assembly and installation please prepare the needed tools as below picture

PARTS INCLUDED

• (C) Green ground screw (1)
• (D) Mounting plate (1)
• (E) Back plate (1)
• (F) Gasket (2)
• (G) Screw (2)
• (H) Frame (1)
• (I) Glass sheet (4)

ACCESSORIES ENCLOSED:

• (A) Mounting screw (2)
• (B) Plastic wire connector (3)

ASSEMBLY & INSTALLATION INSTRUCTIONS

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   • Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
   • Place the wall switch in the “OFF” position.
3. Make assembly

• Step A1: Unscrew screws (G), gaskets (F) and mounting plate (D) from back plate (E), then set them aside for later installation.
• Step A2: Carefully pass the supply wires from the outlet box through mounting plate (D). Secure mounting plate (D) to the outlet box with mounting screws (A).
• Step A3: Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the chart below Connect wires according to the chart below

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.

• Step A4: Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed gaskets (F) and screws (G) as shown in the illustration. Hand tighten until snug.

NOTE: back plate (E) should be snug against the wall with screws (G). If not, remove back plate (E), adjust the threaded length of pre-assembled mounting screws on mounting plate (D):

• Unscrew the pre-assembled hex nuts.

• Screw the pre-assembled mounting screws in or out of mounting plate (D).

• When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.

• Step A5: Install the bulb (Not included) (Please do not exceed the maximum wattage recommended on the socket.)

Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!

ORDERING PARTS

Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.

CLEANING

To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>