ankbit RT5013 Wireless Transmitter and Receiver User Manual
- June 15, 2024
- ankbit
Table of Contents
Wireless
Transmitter and Receiver
User Manual
Model: B06T2
RT5013 Wireless Transmitter and Receiver
In the box
Product Overview
| Button | Function | Operation |
|---|---|---|
| Power on | Press for about is | |
| Enter pairing mode | Press for about 2s | |
| Power off | Press for about 4s | |
| TX | Transmitter mode | Slide to TX to enter transmitter mode |
| RX | Receiver mode | Slide to RX to enter receiver mode |
| Reset | Press for about 2s |
TX mode
RX mode
Control Functions
After pairing successfully in TX mode, the color of the LED will display according to the audio codec supported by the receiving device, it may stay purple/white/blue/cyan/yellow/green.
Note: In RX mode, if there is a sound delay, please double-click button to improve the sound quality.
Instructions
TX Mode:
- Flip the mode button to “TX” Press the button for 2s.When LED light flashes between red and blue ,the adopter will automatically enter into pair mode .
- Put your Bluetooth device such as Bluetooth headphones/earbuds/speaker as close as possible with this adapter.
- Turn on your device’s Bluetooth and pair with B06T2 Bluetooth adapter. They will poir automatically.
- Connect B06T2 with your Phone / TV / Tablet / PC I Laptop / MP3 / MP4 Projector through 3.5mm jack_
- Enjoy the music
RX Mode
- Flip the mode button to “RX”. Press the button for 2s.When LED light flashes between red and blue ,the adapter will automatically enter into pair mode .
- Put your Bluetooth device such as TV/Tablet/PC/Laptop/Phone as close as possible with this adopter
- Turn on your device’s Bluetooth and pair with B06T2 named adopter.
- Connect B06T2 with your speaker/headphone/through 3.5mm jack.
- Enjoy the music.
* How to enter pairing mode?
Press and hold the button for 2 seconds after powered on,B06T2 will enter
the pairing mode (LED lights flashing red and blue).
How to pair the second device?
- Set BO6T2 to pairing mode again {press and hold the button for 2 seconds until the LED flashes red and blue).
- Activate the Bluetooth of the second mobile phone, find “BO6T2’, click connect, and wait for the pairing to succeed.
- Enjoy your music.
Note: You can only play music on one device at a time, so if you want to ploy music on the second device, you need to pause the music on the first device before playing it on the second device.
Charging method
- Plug in the charging cable to charge the BO6T2, and the LED will be steady red.
- When the battery is fully charged, the LED indicator will turn off.(Usually it takes about 2 hours to fully charge the BO6T2)
How to reset the device?
If BO6T2 cannot be connected or does not work normally, please refer to the
following methods to reset the device:
Long press RESET button for 2 seconds, the white indicator light flashes 3
times at the same time, then it will enter pairing mode.
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class 8 digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
CE
ANKBIT international. hereby declares that this product is in compliance with
the essential requirements and other relevant provisions of Directive
2014/53/EU.
In accordance with Article 10(2) and Article 10(10), this product is allowed
to be used in all EU member states.
Warranty
Warranty service is limited to normal use. Any man-made damages such as from connecting to an unsuitable power source, using an unsuitable device, or not following the instructions, as well as damages that did not occur during shipping, repairs, and adjustments not approved by the company, damages from misuse, inattention, or improper installation may cause the warranty to be ineffective immediately. This warranty does not include shipping foes.
Disposal
Always dispose of the used appliance at a recycling centre.
Do not dispose the used appliance together with household waste,
eVatmaster Consulting GmbH Bettinastr, 30
60325 Frankfurt am Main,Germany
[email protected]
Operator: Ankbit International Limited
Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong
Manufacturer: ShenZhen Ankbit Electronics Limited
Address: Runfeng industrial Park, No. 4197 Baoan Blvd, Xixiang St, Baoan Dist,
Shenzhen, China
FCC ID: 2AUFR-RTSOI3
IC: 29252-B03
HVIN: BO6
MADE IN CHINA
Documents / Resources
|
ankbit RT5013 Wireless Transmitter and
Receiver
[pdf] User Manual
RT5013 Wireless Transmitter and Receiver, RT5013, Wireless Transmitter and
Receiver, Transmitter and Receiver, Receiver
---|---