Ankbit B0306 2 In 1 Wireless Transmitter and Receiver User Manual

June 15, 2024
ankbit

Ankbit B0306 2 In 1 Wireless Transmitter and Receiver
Ankbit B0306 2 In 1 Wireless Transmitter and Receiver

Product overview


Wiring installation

TX mode

BOX CONTENTS

Button Function Operation
Enter pairing mode Hold this button for about 2 seconds
Pair the second device Hold this button for about 2 seconds
Transm itter mode Slide to TX to enter transmiter mode

**OFF**

| Power off| Slide to “OFF”

**RX**

| Receiver mode| Slide to RX to enter receiver mode
| Volume up / Next| Short press / In RX mode long press
| Volume down / Previous| Short press / In RX mode long press
Status| LED Indicator
---|---
Pair ing mode| LED flashes fast blue and red
Connected 1st device| LED stays blue/white/yellow/green
Connected 2nd device| TX mode: LED stayspurple/blue/cyan/yellow/green
RX mode: LED stays purple
Disconnected| LED flashes blue once every 3 seconds
Reset| Hold (1) button for about 7 seconds all Leds flashes purple for 3 times

Connect the ML302 to your device with 3.5mm/3.5mm to 2RCA audio cable. (TX mode connects to TV/ RX mode connects to speakers)

Slide to TX mode, press and hold the  button for 2s to enter paring mode(LED flashing red and blue).Set your Bluetooth headphone or Bluetooth speaker to pairing mode.wait for the pairing to succeed ( LED stops flashing) .

RX mode

Dual connection


Charging

  • When it is charging in the OFF mode, the LED will be steady red, and the LED will be off when it is fully charged.
  • When it is charging in the TX/RX mode, the LED will not change.

FCC warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
*RF warning for Mobile device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Slide to RX mode, press and hold the button for 2s to enter paring mode(LED flashing red and blue). Activate the Bluetooth of the mobile phone/computer/tablet, click “ML302” to connect, and wait for the pairing to succeed (LED stops flashing) .

After pairing with the first device, press the button again for 2 seconds (LED flashes red and blue quickly) to enter pairing mode. Then proceed to pairing with the second device, when paired (TX mode: LED stays maybe blue/green/orange/cyan. RX mode: LED stays purple)

LED Indicator


Note:

  1. The specific format needs to be supported by the receiving device
  2. If your Bluetooth devices do not support aptX-HD, the LED will not be green.

Note: In RX mode, if there is a sound delay, please double-click (1) button to improve the sound quality.

Disposal

Always dispose of the used appliance at a recycling centre.
– Do not dispose the used appliance together with household waste.
Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries.

CUSTOMER SERVICES

eVatmaster Consulting GmbH Bettinastr. 30 60325 Frankfurt am Main.Germany contact@evatmaster.com
Operator: Ankbit International Limited
Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong Manufacturer: Shenzhen Ankbit Electronics Limited
Address: Room 401, Building B, Runfeng Industrial Park, No. 4197 Baoan Blvd.,XixiangSt, Baoan Dist, Shenzhen, China
FCC ID: 2A6ET-RT6007

Symbol.png

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals