HAMPTONBAY HDP12070BL Oron 3-Light Black Linear Island Pendant Hanging Light User Manual

HAMPTONBAY HDP12070BL Oron 3-Light Black Linear Island Pendant Hanging

Light

Safety Information

• Consult a qualified electrician with any electrical questions you may have.

IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not continue the assembly process. Please call our Customer Service Team at 1-855-HD-HAMPTON.

Warranty

3-YEAR LIMITED WARRANTY

WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in the materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alterations, neglect or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, assembled, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship.
WHAT IS NOT COVERED
This warranty shall not apply to the finish on any portion of the product due to weathering, as this is considered normal wear. The manufacturer does not warrant and specifically disclaims any warranty, whether expressed or implied, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to, any labor or expense costs involved in the replacement or repair of the product. Contact the Customer Service Team at 1-855-HD-HAMPTON or visit www.HamptonBay.com.

Pre-Installation

PLANNING INSTALLATION
Read all instructions before assembly. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.

NOTE: This light fixture requires the use of four 120V, 60Hz, 60- Watt max., medium-base type A bulbs (not included). Do not exceed the recommended wattage.

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Assembly

Assembling the tubes and body to the canopy

• Carefully unpack the fixture and lay out all parts on a clean surface.
• Determine how many extension tubes you would like to use. The numbers of tubes you use depends on the length you desire for the installed light fixture.
• Feed the fixture wires up through the 12 in. tubes (I), the 6 in. tubes (H) and then the swivels (E).
• Attach the desired number of tubes (H and I) to the fixture body (J) by screwing the tubes in a clockwise direction.
• Screw the two swivels (E) to the ends of the tubes (H and I), and make sure the notches of swivels (E) are facing front.
• Insert the two swivels (E) into the holes in the canopy (D), then secure with two metal washers (C), two tooth lock washers (B) and two nuts (A).

Installation

Installing the cross bar

DANGER: Ensure the power is off at the main fuse box prior to beginning installation.

• Turn off the switch at the wall.
• Turn the power off at the main fuse box.
• Screw the nipple (FF) into the hole in the cross bar (BB) and secure with a lock nut (DD).
• Attach the cross bar (BB) to the ceiling outlet box using the outlet box screws (CC).

Connecting the wires

• Install the fixture bare copper ground wire (1) under the ground screw (EE) on the cross bar (BB).
• Connect the fixture ground wire (1) to the green (or bare, or green & yellow) supply ground wire (2) in the outlet box using a wire nut (AA).
• Connect the white fixture wire (3) to the white supply wire (4) in the outlet box using a wire nut (AA).
• Connect the black fixture wire (5) to the black (or red, or blue) supply wire (6) in the outlet box using a wire nut (AA).

Hanging the light fixture

• Push all excess wires into the outlet box.
• Raise the canopy (D) to the ceiling and then secure in place with the nut (F) and the finial (G).

Assembling the glass shades

• Remove the socket rings (L) from the sockets by unscrewing the socket rings (L).
• Place a glass shade (K) over each socket on the fixture body (J ) and secure it with a socket ring (L).

Installing the bulbs

• Prior to installing the bulbs, inspect sockets for silica packets. If packets are present, then remove and throw away. Do not expose to children or pets.
• Install one 120V, 60Hz, 60-Watt medium-base type A bulb (not included) into each socket of the light fixture.

Care and Cleaning

• Clean the light fixture with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

on position.
The fuse blows or a circuit breaker trips when the light is turned on.| □ There is an exposed wire.

□    There are too many items on one circuit.

| □    Discontinue use of the light fixtur .

□    Contact a qualified electrician or call the Customer Service Team at 1-855-HD-HAMPTON.

□    Unplug other items on the circuit.

Questions, problems, missing parts?
Before returning to the store, call Hampton Bay Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
1-855-HD-HAMPTON HAMPTONBAY.COM
Retain this manual for future use.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>