Ankbit RT5029 Wireless Audio Adapter User Manual
- June 15, 2024
- ankbit
Table of Contents
Wireless Audio Adapter
User Manual
RT5029 Wireless Audio Adapter
|
---|---
|
- Plug
- Automatic power on and enter pairing mode
- Enjoy
|
---|---
Note: The specific format needs to be supported by the receiving device.
LED indication
Status | LED Indicator |
---|---|
Power on | All LED light up for 2 seconds |
Pairing | flash RED and BLUE alternately |
Connected | turn solid BLUE |
Reconnecting | flash BLUE every 1 seconds |
Valid optical audio signal | OPT lights up |
Invalid optical audio signal | OPT flashes |
Valid analogue audio signal | AUX lights up |
Invalid analogue audio signal | AUX flashes |
Audio Playing on PC | USB lights up |
Connected using the aptX LOW LATENCY codec | LL turn solid light |
Connected using the aptX codec | APTX turn solid light |
Connected using the AD codec | AD turn solid light |
Connected using the HD codec | HD turn solid light |
Connected using the SBC codec | SBC turn solid light |
Instructions
- Connect BO6T6 to TV or other device with 3.5mm audio cable.
- Connect the DC 5V power supply, the transmitter will automatically power on into pairing mode(LED lights flashing red and blue).
- Set your device (Bluetooth headphone or Bluetooth speaker) to pairing mode, and wait for the pairing to succeed. (Once connected, the LED will turn SOLID BLUE.)
- Enjoy your music.
* How to enter pairing mode?
Press and hold the button for 2 seconds, BO6T6 will enter the pairing mode.
(LED lights flashing red and blue)
How to pair the second device?
- Set BO6T6 to pairing mode again (press and hold the button for 2 seconds until the LED flashes red and blue).
- Set your second device (Bluetooth headphone or Bluetooth speaker) to pairing mode, and wait for the pairing to succeed.(Once connected, the LED will turn SOLID BLUE.)
- Enjoy your music.
How to reset the device?
If BO6T6 cannot be connected or does not work normally, please refer to the
following methods to reset the device: Press and hold the button for about
7 seconds until the LED flashes purple for 3 times, and then the device will
restart and clear the list of paired devices, and the factory settings will be
restored successfully.
- Ensure that your TV Speaker is set to “External Speaker.”
- Ensure that your TV’s “DOLBY/DTS’ is set to OFF (NOT auto.)
- Ensure the audio cable is good and fully plugged.
Note:
Please make sure that you keep the 3.5mm AUX jack “vacant” while using the
OPTICAL out. (If anything is plugged into the AUX jack, the transmitter will
default to the AUX signal and ignore any OPTICAL input.)
Use with your PC/Laptop
Set BO6T6 as the playback device
To use the Audikast Plus as a microphone device, please go to your audio
settings and select “BO6T6″ as “Microphone and Speaker device.”
Set BO6T6 as the Speakers and Microphone
Note:
If you’d like to use an USB cable that’s not provided by us, please ensure
that the USB cable supports both data syncing and power.
After connecting the micro USB cable as above, you should be able to hear from
your computer through your headphones, and the “USB” indicator on the
transmitter will light up; if not:
Right-click the speaker icon on the bottom-right corner of the PC/laptop
screen and select “Playback devices.” In there, set “BO6T6”” as “Default
Device.”
Audio delay
Bluetooth headphone is NOT aptX LL supported – If your Bluetooth headphone
does not support aptX LOW LATENCY (e.g. Bose, Beats, Sony), it will work with
the BO6T6 using SBC or aptx codec and will experience a 70-220ms latency.
FCC warning:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
*RF warning for Mobile device:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Qualcomm aptx is a product of Qualcomm Technologies, Inc. and/or its
subsidiaries.
Always dispose of the used appliance at a recycling centre. Do not dispose the
used appliance together with household waste.
**** eVatmaster Consulting GmbH
Bettinastr. 30
60325 Frankfurt am Main,Germany
contact@evatmaster.com
Operator: Ankbit International Limited
Address: 45-51 Chatham Road South, Tsim Sha Tsui, Kowloon, Hong Kong
Manufacturer: ShenZhen Ankbit Electronics Limited
Address: Room 401, Building B, Runfeng Industrial Park, No. 4197 Baoan
Blvd.,Xixiang St, Baoan Dist, Shenzhen, China
FCC ID: 2A6ET-RT5029
MADE IN CHINA
Documents / Resources
|
Ankbit RT5029 Wireless Audio
Adapter
[pdf] User Manual
RT5029 Wireless Audio Adapter, RT5029, Wireless Audio Adapter, Audio Adapter
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>