MOEN TV6507BL Two Handle Widespread Lavatory Faucet Instruction Manual
- June 15, 2024
- Moen
Table of Contents
MOEN TV6507BL Two Handle Widespread Lavatory Faucet
HELPFUL TOOLS
For safety and ease of faucet replacement, Moen recommends the use of these helpful tools.
-
Safety Glasses
-
Adjustable Wrench
-
Phillips Screwdriver
-
Sealant
-
Thread Seal Tape
Parts List
A. Spout
B. Handles
C. Upper Mounting Washers (x2)
D. Mounting Bracket
E. Bracket
F. Spout Mounting Nut
G. Mounting Washers (x2)
H. Mounting Ring with screws (x2)
I. Valve Body (Hot)
J. Valve Body (Cold)
K. Mounting Tool
L. Quick Connect Hose
M. Protective Sleeve (x2)
N. Aerator Tool
O. Spout Base
P. Push-Down Drain Plug
Q. Drain Body
R. Drain Gasket
S. Cone Gasket
T. Drain Mounting Nut
U. Lift Rod (for applicable models)
V. Plug
W. Waste Seat
X. Drain Body
Y. Drain Gasket
Z. Drain Hex Nut
AA. Pivot Rod
BB. Pivot Rod Clip
CC. Lift Rod Strap
DD. Pivot Rod Nut
EE. Hex Wrench (for applicable models)
IMPORTANT
-
Spout installs through 1-1/8″ min. dia. hole.
valves install through 1-1/8″ min. dia. hole. -
Maximum hole dia. 1-1/2″.
CAUTION — TIPS FOR REMOVAL OF OLD FAUCET:
Always turn water supply OFF before removing existing faucet or disassembling
the valve. Open faucet handle to relieve water pressure and ensure that
complete water shut-off has been accomplished.
Icon Legend
-
Warning
-
Above sink
-
Below sink
Assembly
Apply a small amount of silicone lubricant to the black rubber O-ring on the
spout base (O) as shown. Install into Spout (A).
Apply a bead of sealant to the base of the spout. Install Spout (A) into
sink deck opening as shown.
- Install Mounting Bracket (D), Mounting Plate (E) onto shank of Spout Assembly (A) as illustrated above for sink decks less than 1″. Finger tighten bracket and plate with Mounting Nut (F).
Mounting illustration for sinks less than 1″
Mounting illustration for sinks greater than 1″, as Mounting Plate (E) is
only needed.
-
Attach Mounting Tool (K) to Mounting Bracket Nut (F) as shown.
-
Hand tighten nut.
-
Insert Screwdriver into hole of Mounting Tool (K).
-
Further tighten Mounting Bracket Nut (F).
Note: Upper Mounting Washer (C) has “UP” for correct installation
orientation.
Apply sealant into underside groove of Upper Mounting Washers (C) (x2).
Flip over to install onto sink deck, right side up with “UP” visible.
Insert hot and cold valve bodies (I) and (J) through Mounting Washers
(C) as illustrated.
Partially install screws from mounting ring into Mounting Ring (H).
- Slide Mounting Washer (G) and Mounting Ring with screws (H) onto valve body (I) (hot).
- Thread Mounting Ring (H) and hand tighten.
Finish tightening with screwdriver. Repeat sequence from steps 10 and 11
for valve body (J) (cold-not shown).
Remove Protective Sleeves (M) from valve bodies (I) (hot) and (J)
(cold).
Attach Quick Connect Hose (L) to the bottom of the waterway tube.
Push hose (L) up as far as possible, until a “click” is heard. Tug
downward to test engagement. If necessary, click button to disengage Hose
(L).
Install ends of Quick Connect Hose (L) onto each valve body for correct
installation orientation as shown with arrow facing up.
Push hose ends up until a “click” is heard. Tug downward to test engagement.
Turn stems of Valve Bodies (I) and (J) to the closed position.
Install faucet handles (B) to valve bodies (I) and (J).
Hold lever of handle and tighten base to deck until secure. When handle is flush with deck, rotate approximately quarter turn so the flat faces forward.
For Type A Waste Install: follow steps 18 – 20.
For Type B Waste Install: follow steps 21 – 29.
|
- Clean drain opening in the bottom of the sink.
- Place Drain Body (Q) with Gasket (R) into opening of sink.
Install Cone Gasket (S) onto Drain Body (Q). Tighten with Drain Mounting Nut **(T).
**
-
Install the Push-Down Drain Plug (P) into the Drain Body (Q).
-
Press down to actuate the pop-up mechanism. Go to Step 30.
-
Clean drain opening in the bottom of sink.
-
Apply a generous amount of sealant to the underside of the Waste Seat (W).
Insert Waste Seat (W) through sink drain opening.
Assemble Drain Body (X) to Waste Seat (W). Tighten by hand.
- Install Lift Rod (U) (for applicable models) through faucet into Lift Rod Strap (CC).
- Hand tighten nut of strap.
Ensure pivot rod opening on Drain Body (Q) points toward the faucet and
wall as illustrated.
- Make final tightening of Drain Hex Nut (Z) to Drain Body (Q) with wrench.
- Insert Waste Plug (V) into sink opening.
The Pivot Rod (AA) can be installed in two ways. The circle illustration shows the Pivot Rod (AA) next to hole in Waste Plug (V). This allows the Waste Plug (V) to be pulled out for cleaning. Box illustration shows the Pivot Rod (AA) inserted into the hole in the Waste Plug (V). This prevents the Waste Plug (V) from being easily removed after installation. Tighten the Pivot Rod Nut **(DD).
**
-
Push Pivot Rod (AA) down.
-
After clip is placed over closest hole on Lift Rod Strap (CC), squeeze Pivot Rod Clip (BB).
-
Slide Pivot Rod (AA) through clip and strap holes.
-
Loosen nut on Lift Rod Strap (CC) to allow Lift Rod (U) to rest in faucet.
-
Verify Pivot Rod (AA) is still pushed down, and Waste Plug (V) is open in the sink.
-
Tighten nut with wrench.
Attach flexible supply lines (not included) to valve bodies as shown. Tighten
with wrench.
Attach other ends of supply lines to stops.
Tighten flexible supply lines to stops with wrench.
Turn water on. Installation complete.
Follow steps A – D for flushing.
Attach Aerator Tool (N) to aerator from Spout (A) and remove. Set
aerator aside for re-installation.
Turn handles on and run water for 15 seconds to flush any possible debris.
Turn handles off.
Follow steps E – H for flushing for model 84461SRN.
Using Aerator Tool (N), re-install aerator to Spout (A). Finger
tighten until aerator is secure.
Insert Hex Wrench (EE) into aerator hole. Loosen aerator with hex wrench
and remove.
Turn on water to flush aerator for 15 seconds.
Turn off water.
Re-install aerator and tighten with Hex Wrench (EE).
Moen Limited Lifetime Warranty
Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “Warranty Period” for homeowners), that this product will be leak- and drip-free during normal use and all parts and finishes of this product will be free from defects in material and manufacturing workmanship. All other purchasers (including purchasers for industrial, commercial and business use) are warranted for a period of 5 years from the original date of purchase (the “Warranty Period” for non-homeowners).
If this product should ever develop a leak or drip during the Warranty Period,
Moen will FREE OF CHARGE provide the parts necessary to put the product back
in good working condition and will replace FREE OF CHARGE any part or finish
that proves defective in material and manufacturing workmanship, under normal
installation, use and service. Replacement parts may be obtained by calling
1-800-289- 6636 (Canada
1-800-465-6130), or by writing to the
address shown.
Proof of purchase (original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Defects or damage caused by the
use of other than genuine Moen parts is not covered by this warranty. This
warranty is applicable only to products purchased after December, 1995 and
shall be effective from the date of purchase as shown on purchaser’s receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However, damage due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether performed by a contractor, service company, or yourself, are excluded from this warranty. Moen will not be responsible for labor charges and/ or damage incurred in installation, repair or replacement, nor for any indirect, incidental or consequential damages, losses, injury or costs of any nature relating to this product. Except as provided by law, this warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or implied, statutory or otherwise, including without restriction those of merchantability or of fitness for use.
Some states, provinces and nations do not allow the exclusion or limitation of
incidental or consequential damages, so the above limitations or exclusions
may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state, province to
province, nation to nation. Moen will advise you of the procedure to follow in
making warranty claims.
Simply write to Moen Incorporated using the address below. Explain the defect
and include proof of purchase and your name, address, area code and telephone
number.
Customer Support
Moen Incorporated
25300 Al Moen Drive
North Olmsted, Ohio 44070-8022
U.S.A.
PLEASE CONTACT MOEN FIRST
For Installation Help, Missing or Replacement Parts
(USA) 1-800-BUY-MOEN (1-800-289-6636)
www.moen.com
(Canada) 1-800-465-6130
www.moen.ca
Image is for reference only
(Style varies by model)
Record Purchased Model Number:
(Save instruction sheet for future reference)
Register Online:
www.moen.com/product-registration
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>