NEEWER LF-04 Video LED Light User Manual

NEEWER LF-04 Video LED Light

Preface
LED photography light source is stable, high quality color temperature, powerful, suitable for studio shooting, interview light, still life shooting and video shooting. Can be selected with a special remote control, wireless packet dimming, wireless brightness adjustment, rich functions, convenient operation.

The product has the following highlights:

• The high-power COB LED lamp with high brightness and stable light source.
•  The guider no higher than 95 , which truly reduces the color of the object
• LCD display parameters (after setting for 8 seconds) are saved automatically.
•  Optional remote control, 2.4 GHz wireless grouping control with 16 groups and 16 channels , wireless adjustment of each group brightness.
• Equipped with heat sink and built-in fan for efficient heat dissipation to control the temperature protection and extended lamp life.

Note

• Don’t place the light in a high temperature and high humidity place. The light with temperature protection function. When the temperature is too high, it enters the protection state and returns to normal when the temperature be decreased .
• Don’t touch the product with wet hands and do not immerse the product in water or be exposed to rain.
• Don’t remove or modify products. If the product is damaged by fall or other accident, please send the product to the manufacturer’s authorized maintenance center for inspection and repair.

Display screen

Product Description

Use of guidelines

1. Start Using led Lights
   • Connect AC power supply
   •  Press the ON / OFF button to turn on the power, and the digital display panel in on.
2. LED light switch
   • After the power is turned on, press “RUN” to turn the light on or off.
3. Brightness
   • After the power is turned on, the adjusting knob to adjust the power.
   • Adjustable power range: 10 % -100 %
4. Channel / Group
   • Press”GR/CH” knob until “ ”flicker in the display.then select the dial setting(1-16) channel, and then press the dial key to confirm;
   • Press”GR/CH” knob until “ ”flicker in the display, then select the dial setting(0-9, A-F) group, and then press the dial key to confirm.

Note: the flash parameters will not be stored until 8 seconds after setting.

Temperature detection
This light always detects the temperature of LED light .When the temperature too high,the light will be turn off .

Remote control

(Remote control purchased by separately)

• Press the < > button to control the LED light on or off
• Press<+>, <->to adjust the brightness of the light
• Press the “CH” key, flicker < >on the screen, and press the <+> <-> key to set the channel.
• Press the “GR” key, flicker < > on the screen, and then press the “+” “-”-” key to set the group.

Note :*Please keep the same channel and same group for light and remote .

If the light without color temperature adjustment function, the “COLOR”( color temperature )key is not supported.It will take 8 seconds for the remote control parameter setting to be memorized and saved

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.  this device may not cause hannful interference, and
2.  this device must accept any interference received, including interference that may cause undesired operation

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>