FINGeRTEC Face ID 6 Hybrid Face Recognition Access Device Installation Guide
- June 9, 2024
- FINGeRTEC
Table of Contents
Installation Guide
Face ID 6 Hybrid Face Recognition Access Device
Step 1
Determine the Installation Location
- Avoid installing the terminals in locations that have contact with strong light source (e.g direct sunlight, spotlight, fluorescent light, etc)
Indoor Use| Avoid Glass Refraction| Avoid Direct Sunlight
And Exposure| Far Away Heat Source| Keep Effective Distance
0.3-2.5m
- Avoid installing the terminals in locations with high moisture or condensation levels in the air
- The recommended installation height of the terminal from the ground to the camera is 1.5 meter.
Step 2
Mount Terminal on a Wall
- Avoid strong sunlight
- Install the terminal 1.5m from the ground level (measure the height from the ground to the face camera)”
After measuring the height accordingly and make relevant markings on the wall,
drill the screws into the wall to secure the back plate.
Attach the terminal to the back plate and tighten the screws.
Refer to Appendix II for dimensions and measurements of installation.
Step 3
Wiring for Power Supply
Use power cables (black and red) to connect to a linear power supply with specifications of 12VDC 3A to Power Port.
Step 4
Setting Up Data Communications
(Skip this step if you are using USB flash disk to transfer data)
The data communication ports are positioned at the rear of the terminal,
please refer to the diagram shown on Step 3 to determine the wiring. Plug the
communication jacks
(TCP/IP) to the corresponding ports.
TCP/IP – LAN Connection
For TCP/IP connection, plug the special RJ45 jack into the TCP/IP (LAN) Port
of the terminal. Connect the other end (normal RJ45 jack) to the local area
network hub or a PC. Configure the device ID, IP ad- dress, subnet mask and
Gateway in the terminal (refer to the hard- ware user manual for details).
Step 5
Finalizing the installation
- Check that all cable connections are done correctly.
- Attach the terminal to the corresponding back plate, tighten the screws to fix the terminal on a wall.
- Switch on the power to the terminal.
- Start using it.
Other Accessories
Note: All Accessories are offered at http://accessory.fingertec.com
AdapTec Plus
The AdapTec Plus is a 12VDC power supply inclusive of a 110~240VAC switching
linear power. The AdapTec Plus supplies 12VDC power to the FingerTec terminal
and door lock system as well as charges a 12VDC 7.0Ah backup battery
simultaneously. During an event of a power failure, the back up battery
automatically provides power to
the terminal and maintains the door lock system. The AdapTec Plus also
prevents a secured door from being opened if it has been tampered with.
Door Lock Accessories
FingerTec offers various door locks accessories to complement the door access
product range.
Appendix I
Power Supply & Door Lock System Wiring Diagrams
Diagram1 • Normally Close (NC)
Diagram 2 • Normally Open (NO)
Diagram 3 • Other Accessories
Use either Type NO or Type NC alarm device.
Door Lock Connectors
| WIRING PORT | USAGE |
|---|---|
| SEN | Door Sensor (SEN-GND) Release Button (BUT-GND) |
GND
BUT
NO1| Dry Contact
(Independent power supply for door lock)
•NO type door lock (N01-COM)
•NC type door lock (NC1-COM)
Power Contact (Using power from terminal to power on door lock)
•NO type door lock (N01-GND)
•NC type door lock (NC1-GND)
NCI
COM| Dry Contact (independent power supply for door lock)
•NO type door lock (N01-COM)
•NC type door lock (NC1-COM)
Power Contact (using power from terminal to power on door lock)
•COM1 – +12V
AL+| Alarm System
AL-
The terminal will trigger the alarm output in the following situations:
- Door forced open (A door sensor must be installed)
- Door open time out (A door sensor must be installed)
- Terminal has been illegally dismantled
Appendix II
Terminal Dimensions and Measurements
TimeTec © 2022, All Rights Reserved • 122022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>