MOEN YB8863CH 90 Degree 3 Light Dual Mount Bath Bathroom Vanity Fixture Installation Guide

Table of Contents

MOEN-YB8863CH-90-Degree-3-Light-Dual-Mount-Bath-Bathroom-Vanity-Fixture-
PRODUCT-IMAGE

MOEN-YB8863CH-90-Degree-3-Light-Dual-Mount-Bath-Bathroom-Vanity-Fixture-
IMAGE-1

Don’t forget to register and review your product by scanning the code or visiting moen.com/product-registration.
Download reader at getscanlife.com.

Included Hardware

MOEN-YB8863CH-90-Degree-3-Light-Dual-Mount-Bath-Bathroom-Vanity-Fixture-
IMAGE-5

Diagram

Important Notes

Turn off main power supply during installation. Do not connect or disconnect under load. Maximum voltage 150 v

LIMITED LIFETIME WARRANTY

If this product fails due to materials or workmanship at any time during the life of the product, Moen Incorporated will replace it free of charge, postage paid. Simply contact Moen Accessories at 1-800-822-0116 for replacement information. This warranty does not cover products which have been abused, altered, damaged, misused, cut or worn. Do not install this product into non-recommended substrates and substrate thicknesses or substrates that are weakened or damaged in any way prior to installation. Do not install this product on a curved surface. Consult a professional if you determine area to be drilled contains electrical, plumbing or other obstructions. TO THE EXTEND PERMITTED BY LAW, MOEN and MOEN ACCESSORIES DISCLAIMS ALL OTHER IMPLIED OR EXPRESS WARRANTIES INCLUDING ALL WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE

LIMITATION OF LIABILITY

THIS WARRANTY IS YOUR SOLE REMEDY AND MOEN SHALL NOT BE LIABLE FOR DAMAGES, WHETHER DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL, EXEMPLARY, OR OTHERWISE, INCLUDING LOST REVENUES AND LOST PROFITS, ARISING OUT OF ANY THEORY OR RECOVERY, INCLUDING STATUTORY, CONTRACT OR TORT. NOTWITHSTANDING
THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL MOEN’S ENTIRE
LIABILITY EXCEED THE PURCHASE PRICE OF THIS PRODUCT. SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE RIGHTS WHICH VARY FROM STATE TO STATE AND PROVINCE TO PROVINCE.
- For additional warranty information, visit www.moen.com

Turn off main power supply.
Disconnect quick connect wires from light assembly.
Connect quick connect wires to electrical box wires as show below using provided wire nuts.
Thread the 38 mm screws into the appropriate holes from the backside.
Use level to ensure the 38 mm screws are vertical. Once level, attach the mounting plate to the electrical box with the provided 18 mm screws
Connect the Quick Connect wires.
Place the light assembly over the screws. Then, place the decorative nuts over the screws and tighten until firm.
To install the globe to the light assembly, first place the globe over the socket. Then place the socket ring onto the socket and tighten until firm. May require extender between socket ring and globe. [Use the socket installation tool, if provided
Install proper rated light bulb. Maximum bulb is 100 watt type A.
Turn on the power supply and verify that light works.

25300 Al Moen Drive

North Olmsted, OH 44070-8022
- Customer Service USA: 1-800-882-0116
- International Customer Service: 1-440-962-2263
Moen is a registered trademark of Moen Incorporated ©2014
- www.moen.com
25300 Al Moen Drive
- North Olmsted, OH 44070-8022, USA
- Service a la clientele aux USA : 1-800-882-0116
- Service a la clientele international: 1-440-962-2263
- 25300 Al Moen Drive
- North Olmsted, OH 44070-8022 –
Moen es Moen Incorporated ©2014
- www.moen.com