WALI TVDVD-5 Universal TV Stand Instruction Manual
- June 15, 2024
- WALI
Table of Contents
WALI TVDVD-5 Universal TV Stand
Product Information
- Product Name: Table Top TV Stand
- Model Number: TVDVD-5
- Compatibility: Min: 150x100mm
- Max: 600x400mm
- TV Size Range: 30-70 inches
- Weight Capacity: 40kg (88lbs)
- Contact Information:support@walielectric.com
WARNING
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
WARNING: TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER.
TO HELP PREVENT TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
Installation Instructions
- Step 1: Tear off the protective paper to attach Foot Pads I near the bottom four corners of the Base ① as image shown.
- Step 2: Connect two Support Pillar & ③ . Then insert 4pcs Screws E through the holes of Support Pillar ② & ③ , and tighten using Allen Key 4mm J1.
- Step 3: Put Base ① on the table; put Washer B and M6×30mm Bolts A on the base; put Plastic Cover F and Support Pillar ③ under the base. Then tighten the bolts A using Allen Key 4mm J1.
- Step 4: Connect TV Plate ⑤ and Angle Adjuster ⑦ by using Connecting Plate ⑥ and M6 Nuts C. Tighten the nuts using the Wrench J2.
- Connect TV Plate Unit to Support Pillar ② at your desired position (three options) using Bolts D1 and Washers D2. Tighten them using Allen Key 4mm J1.
Step 5
Step 5.1: Select TV Screws
- Only one screw size fits your TV
- Hand thread screws into the threaded inserts on the back of your TV to determine which screw diameter (M6 or M8) to use.
Step 5.2: Select Spacers ( if needed )
- NOT NEEDED
- NEEDED FOR
Step 5.3: Attach the TV Brackets
- Attach the TV Brackets 4 to the back of TV using TV screws, washers and spacers.
Step 6
- Choose the appropriate position (three options) for your TV.
- Hang your TV with brackets onto the TV plate. Put the Safety Lock G in place and tighten the fixing screw to the TV plate securely.
Step 7
- Attach Wire Clips H into the holes of Support Pillar ② & ③.
- Guide the cable through the Wire Clips H.
Adjustments: Swivel Adjustment
- Refer to the below illustrations to adjust swivel angle.
Note: When the TV Stand is placed against the wall, the actual swivel angle is determined by the screen size.
Tilt Adjustment: (If necessary)
- Loosen 4 tilting bolts by MAXIMUM 1 turn using Wrench J2.
- Hold the TV with your hands, then adjust TV to your desired angle.
- Tighten 4 tilting bolts using Wrench J2.
Product Dimensions
CONTACT
Thank you for choosing us
- We support the technology that brings your home to life.
- We offer high quality products, professional customer service, and extensive technical support.
If you have any questions,please contact us.
- 1-844-SATTLER (18447288537)
- support@walielectric.com
- www.walielectric.com
INFO
Documents / Resources
| WALI
TVDVD-5 Universal TV
Stand
[pdf] Instruction Manual
TVDVD-5, TVDVD-5 Universal TV Stand, TVDVD-5 Universal TV Stand, Universal TV
Stand, TV Stand, Stand
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>