HALO HLB3 6 Inch Square Recessed LED Ceiling and Shower Light Instruction Manual

: June 15, 2024
: HALO

Table of Contents

IB518193ML
HLB-3”, HLB-4” and HLB-6” Series Instructions

IB518193ML

HLB-3”, HLB-4” and HLB-6” Series Instructions

Packaging Contents

A. HLB and connector, round

B. HLB and connector, square

C. J-Box, dedicated, 3”

D. J-Box, dedicated, 4” and 6”

E. J-Box, selectable, 4” and 6”

HALO HLB3 6 Inch Square Recessed LED Ceiling A5

Selector Switch (2700K, 3000K, 3500K, 4000K, 5000K)
Choose your favorite correlated color temperature (CCT) from 5 options using the switch

ITEMS REQUIRED

(Purchase separately)

Gloves

IMPORTANT SAFETY INSTRUCTIONS

When using product, basic precautions should always be followed, including the following:

Heed all warnings, including below warnings AND those included on product.
HALO® recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.

WARNING

Read and follow these instructions.

Risk of Fire – MINIMUM 90°C SUPPLY CONDUCTORS.
If uncertain, consult an electrician.

Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

Risk of Fire/Electric Shock
**** – LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for installation of LED retrofit kit. Check for enclosed wiring and components.

Install this kit only in the luminaires that have the construction features shown in the photographs and/ or drawings.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

CAUTION

Edges may be Sharp – Wear gloves while handling.

Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids the warranty.
Fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Only those open holes indicated in the photographs and /or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.

SAVE THESE INSTRUCTIONS AND WARNINGS.

DIMMING

Halo HLB is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. Note some dimmers require a neutral in the wallbox.) For the latest Halo HLB product information, please refer to specifications online at www.eaton.com.

DETERMINING WHICH INSTALLATION METHOD TO USE

The HLB models can be installed directly into a ceiling without requiring separate JBOX or recessed housings.

WARNING

Risk of Electric Shock – To avoid possible electrical shock, be sure that power supply is turned off at fuse box or circuit breaker before installing or servicing luminaire.

WIRING

Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1). Make sure the opening is not larger than the outer flange of the LED module.
Open the cover of the provided jbox and insert the supply wires through the preferred strain reliefs in the provided jbox (Fig. 3). Connect the bare copper (ground) wire from the jbox to the ground wire of the supply connection using the provided wire nut.
Connect the black/white leads from the output of the driver to the appropriate supply side wiring using the provided wire nuts.
Close the cover after properly securing the supply wire to the provided jbox on the rear of the LED module.
Module is ready to install into ceiling. (See MOUNTING section for specific instructions).

MOUNTING

Connect the remote driver box to the light fixture. (Fig. 2)
Place remote driver box thru the cut-out hole and mount according to local code as required.
Bundle any excess wire and place into ceiling above the module according to local code as required.
Rotate both mousetrap springs upward to allow passage through the cutout in the ceiling (Fig.3).
Continue to press the module through the cutout in the ceiling until the perimeter flange of the module is flush against the ceiling.
The springs will rotate back into position and hold the LED module tight to the ceiling.

Fig. 1

Fig. 2

Fig. 3

Wire traps
Trampa para cables

Fig. 4

REMOVAL

CAUTION

Risk of pinching – Do not place hands under springs during removal of the LED module.

Simply pull down firmly on LED module until mousetrap springs release from the ceiling. Reach through the ceiling to hold mousetrap springs up and away from the ceiling as you continue to pull the module from it’s opening.
Disconnect wiring.

5-YEAR LIMITED WARRANTY

THE FOLLOWING WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.

Eaton warrants to customers that, for a period of five years from the date of purchase, Eaton products will be free from defects in materials and workmanship. The obligation of Eaton under this warranty is expressly limited to the provision of replacement products. This warranty is extended only to the original purchaser of the product.

A purchaser’s receipt or other proof of date of original purchase acceptable to Eaton. This is required before warranty performance shall be rendered.

This warranty does not apply to Eaton products that have been altered or repaired or that have been subjected to neglect, abuse, misuse or accident (including shipping damages). This warranty does not apply to products not manufactured by Eaton which have been supplied, installed, and/or used in conjunction with Eaton products. Damage to the product caused by replacement bulbs or corrosion or discoloration of brass components are not covered by this warranty.

LIMITATION OF LIABILITY:
IN NO EVENT SHALL EATON BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (REGARDLESS OF THE FORM OF ACTION, WHETHER IN CONTRACT, STRICT LIABILITY, OR IN TORT INCLUDING NEGLIGENCE), NOR FOR LOST PROFITS; NOR SHALL THE LIABILITY OF EATON FOR ANY CLAIMS OR DAMAGE ARISING OUT OF OR CONNECTED WITH THESE TERMS OR THE MANUFACTURE, SALE, DELIVERY, USE, MAINTENANCE, REPAIR OR MODIFICATION OF EATON PRODUCTS, OR SUPPLY OF ANY REPLACEMENT PARTS THEREFORE, EXCEED THE PURCHASE PRICE OF EATON PRODUCTS GIVING RISE TO A CLAIM. NO LABOR CHARGES WILL BE ACCEPTED TO REMOVE OR INSTALL FIXTURES.

All returned products must be accompanied by a Return Goods Authorization Number issued by the Company and must be returned freight prepaid. Any product received without a Return Goods Authorization Number from the Company will be refused.

Eaton is not responsible for merchandise damaged in transit. Repaired or replaced products shall be subject to the terms of this warranty and are inspected when packed. Evident or concealed damage that is made in transit should be reported at once to the carrier making the delivery and a claim filed with them.

Reproductions of this document without prior written approval of Eaton are strictly prohibited.

Eaton
1121 Highway 74 South
Peachtree City, GA 30269
eaton.com/lighting

© 2019 Eaton
All Rights Reserved
Printed in USA

Eaton is a registered trademark.
All trademarks are property of their respective owners.

HLB3, HLB4 and HLB6 Round Ceiling Templates

HALO HLB3 6 Inch Square Recessed LED Ceiling B5