TELTONIKA FMM800 OBDII Simple Tracker Owner’s Manual

: June 15, 2024
: teltonika

Table of Contents

KNOW YOUR DEVICE
SET UP YOUR DEVICE
PC CONNECTION (WINDOWS)
HOW TO INSTALL USB DRIVERS (WINDOWS)
CONFIGURATION
QUICK SMS CONFIGURATION
DEFAULT CONFIGURATION SETTINGS
MOUNTING RECOMMENDATIONS
LED INDICATIONS
SAFETY INFORMATION
CERTIFICATION AND APPROVALS
WARRANTY
WARRANTY DISCLAIMER
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FMM800
Simple OBDII tracker
Quick Manual v1.4

KNOW YOUR DEVICE

PINOUT

Pin number	Pin name	Description
4	GND (-)	Ground
5	GND (-)	Ground
16	VCC (10 – 30)V
DC(+)	Power supply (+10 – 30

V DC

SET UP YOUR DEVICE

HOW TO INSERT MICRO-SIM CARD AND CONNECT THE BATTERY

| | |
---|---|---|---
1 COVER REMOVAL
Gently remove FMM800 cover using plastic pry tool from both sides.| 2 MICRO- SIM CARD INSERT Insert Micro-SIM card as shown with PIN request disabled or read our Wiki 1 how to enter it later in Teltonika Configurator 2 .
Make sure that MicroSIM card cut-off corner is pointing forward to slot.
1 wiki.teltonika-gps.com/view/ FMM800_Securityinfo
2 wiki.teltonika.lt/view/Teltonika Configurator| 3 BATTERY CONNECTION
Connect battery as shown to device. Position the battery in place where it does not obstruct other components.| 4 ATTACHING COVER BACK
Device is ready to be connected.
Attach device cover back.

PC CONNECTION (WINDOWS)

Power-up FMM800 with DC voltage (10 – 30 V) power supply using supplied power cable. LED’s should start blinking, see “LED indications 1 ”.
Connect device to computer using Micro-USB cable or Bluetooth connection:
• Using Micro-USB cable
• You will need to install USB drivers, see “How to install USB drivers (Windows) 2 ”
• Using Bluetooth
• FMM800 Bluetooth is enabled by default. Turn on Bluetooth on your PC, then select Add Bluetooth or other device

Bluetooth. Choose your device named – “FMM800_last_7_imei_digits”, without LE in the end. Enter default password 5555, press Connect and then select Done.
You are now ready to use the device on your computer.
1 wiki.teltonika-gps.com/view/FMM800A_LED_status
2 Page 6, “How to install USB drivers”

HOW TO INSTALL USB DRIVERS (WINDOWS)

Please download COM port drivers from here 1 .
Extract and run TeltonikaCOMDriver.exe.
Click Next in driver installation window.
In the following window click Install button.
Setup will continue installing the driver and eventually the confirmation window will appear. Click Finish to complete the setup.
1 teltonika.lt/downloads/en/FMM800/TeltonikaCOMDriver.zip

CONFIGURATION

At first FMM800 device will have default factory settings set. These settings should be changed according to the users needs. Main configuration can be performed via Teltonika Configurator 1 software. Get the latest Configurator version from here
2 . Configurator operates on Microsoft Windows OS and uses prerequisite MS .NET Framework. Make sure you have the correct version installed.

1 wiki.teltonika-gps.com/view/Teltonika_Configurator
2 wiki.teltonika-gps.com/view/Teltonika_Configurator_versions

MS .Net requirements

Operating system	MS .NET Framework version	Version	Links

Windows Vista
Windows 7
Windows 8.1
Windows 10| MS .NET Framework 4.6.2| 32 and 64 bit| www.microsoft.com

1 dotnet.microsoft.com/en-us/download/dotnet- framework/net462

Downloaded Configurator will be in compressed archive.
Extract it and launch Configurator.exe. After launch software language can be changed by clicking ? in the right bottom corner.Configuration process begins by pressing on connected device.

After connection to Configurator Status window will be displayed.

Various Status window 1 tabs display information about GNSS 2 ,GSM 3 , I/O 4, Maintenance 5 and etc. FMM800 has one user editable profile, which can be loaded and saved to the device.
After any modification of configuration the changes need to be saved to device using Save to device button. Main buttons offer following functionality:

| Load from device – loads configuration from device.
---|---
| Save to device – saves configuration to device.
| Load from file – loads configuration from file.
| Save to file – saves configuration to file.
| Update firmware – updates firmware on device.
| Read records – reads records from the device.
| Reboot device – restarts device.
| Reset configuration – sets device configuration to default.

Most important configurator section is GPRS – where allyour server and GPRS settings6can be configured and DataAcquisition7– where data acquiring parameters can beconfigured. More details about FMM800 configuration usingConfigurator can be found in our Wiki 8 .

1 wiki.teltonika-gps.com/view/FMM800_Status_info
2 wiki.teltonika-gps.com/view/FMM800_Status_info#GNSS_Info
3 wiki.teltonika-gps.com/view/FMM800_Status_info#GSM_Info
4 wiki.teltonika-gps.com/view/FMM800_Status_info#I.2FO_Info
5 wiki.teltonika-gps.com/view/FMM800_Status_info#Maintenance
6 wiki.teltonika-gps.com/view/FMM800_GPRS_settings
7 wiki.teltonika-gps.com/view/FMM800_Data_acquisition_settings
8 wiki.teltonika-gps.com/view/FMM800_Configuration

QUICK SMS CONFIGURATION

Default configuration has optimal parameters present to ensure best performance of track quality and data usage.
Quickly set up your device by sending this SMS command to it:

Note: Before SMS text, two space symbols should be inserted.

GPRS SETTINGS:

2001 – APN
2002 – APN username (if there are no APN username, empty field should be left)
2003 – APN password (if there are no APN password, empty field should be left)
SERVER SETTINGS:
2004 – Domain
2005 – Port
2006 – Data sending protocol (0 – TCP, 1 – UDP)

DEFAULT CONFIGURATION SETTINGS

MOVEMENT AND IGNITION DETECTION:

|
---|---
VEHICLE MOVEMENT
will be detected by accelerometer
DEVICE MAKES A
RECORD ON STOP IF:| IGNITION
will be detected by vehicle power voltage between 13,2 – 30 V
RECORDS SENDING TO
SERVER:
|
1 HOUR PASSES while vehicle is stationary and ignition is off| EVERY 120 SECOND it is sent to the server If device has made a record

DEVICE MAKES A RECORD ON MOVING IF ONE OF THESE EVENTS HAPPEN:

|
---|---
PASSES
300 seconds| VEHICLE DRIVES
100 meters
|
VEHICLE TURNS
10 degrees| SPEED DIFFERENCE
between last coordinate and current position is greater than 10 km/h

After successful SMS configuration, FMM800 device will synchronize time and update records to configured server. Time intervals and default I/O elements can be changed by using Teltonika Configurator 1 or SMS parameters2.

1 wiki.teltonika-gps.com/view/Teltonika_Configurator
2 wiki.teltonika- gps.com/view/Template:FMB_Device_Family_Parameter_list

MOUNTING RECOMMENDATIONS

CONNECTING THE DEVICE TO THE VEHICLE:
Find OBDII connector in your vehicle.

LED INDICATIONS

NAVIGATION LED INDICATIONS

Behaviour	Meaning
Permanently switched on	GNSS signal is not received
Blinking every second	Normal mode, GNSS is working
Off	GNSS is turned off because:

Device is not working or Device is in sleep mode
Blinking fast constantly| Device firmware is being flashed

STATUS LED INDICATIONS

Behaviour	Meaning
Blinking every second	Normal mode
Blinking every two seconds	Sleep mode
Blinking fast for a short time	Modem activity
Off	Device is not working or Device is in boot mode

BASIC CHARACTERISTICS

Module

Name| FMM800-Q3IB0: Quectel BG95-M3 with Teltonika TM2500
Technology| LTE CAT M1/NB-IoT/GSM/GPRS/ GNSS/BLUETOOTH
GNSS
GNSS| GPS, GLONASS, GALILEO, BEIDOU, SBAS, QZSS, DGPS, AGPS
Receiver| 33 channel
Tracking sensitivity| -165 dBM
Accuracy| < 3 m
Hot start| < 1 s
Warm start| < 25 s
Cold start| < 35 s
Cellular
2G bands| FMM800-Q3IB0: GSM: B2/B3/B5/B8
4G bands| FMM800-Q3IB0: LTE-FDD (CAT M1): B1/B2/B3/B4/B5/B8/B12/B13/B18/ B19/B20/B25/B26/B27/B28/B66/B85
FMM800-Q3IB0: LTE-FDD (CAT NB2): B1/B2/B3/B4/B5/B8/B12/B13/B18/
B19/B20/B25/B28/B66/B71/B85LTE: LTE FDD (CAT-M1): Max. 588Kbps (DL)/Max.1119Kbps (UL)
Data transfer| LTE: LTE FDD (CAT-M1): Max. 588Kbps (DL)/Max.1119Kbps (UL) LTE: LTE FDD (CAT-NB2): Max.
127Kbps (DL)/Max.158.5Kbps (UL) GSM: GPRS: Max. 107Kbps (DL)/ Max. 85.6Kbps (UL)
Data support| SMS (text/data)
POWER
Input voltage range| 10 – 30 V DC with overvoltage
protection
Back-up battery| 170 mAh Li-Po battery 3.7 V (0.63
Wh)
Internal fuse| 3A, 125V
BLUETOOTH
Specification| 4.0 + LE
Supported
peripherals| Temperature and Humidity sensor 1 , Inateck Barcode Scanner, Universal BLE sensors support
INTERFACE
Connection| OBDII socket
GNSS antenna| Internal High Gain
GSM antenna| Internal High Gain
USB| 2.0 Micro-USB
LED indication| 2 status LED lights
SIM| Micro-SIM
Memory| 128MB internal flash memory
PHYSICAL SPECIFICATION
Dimensions| 67,2 x 49,6 x 25 mm (L x W x H)
Weight| 63 g
OPERATING ENVIRONMENT
Operating
temperature
(without battery)| -40 °C to +85 °C
Operating
temperature| -40 °C to +85 °C
(with battery)| -20 °C to +40 °C
Storage temperature
(without battery)| -40 °C to +85 °C
Storage temperature
(with battery)
Operating humidity| 20 °C to +45 °C5% to 95% non-condensing
Ingress Protection
Rating| IP41
Battery charge
temperature| 0 °C to +45 °C
Battery discharge
temperature| -20 °C to +60 °C
Battery storage
temperature| 20 °C to +45 °C for 1 month20 °C to +35 °C for 6 months
FEATURES
Sensors| Accelerometer
Scenarios| Green Driving 1 , Over Speeding detection 2 , Jamming detection 3 , GNSS Fuel Counter 4 , Excessive Idling detection 5 , Unplug detection 6 , Towing detection 7 , Crash detection 8 , Auto Geofence 9 , Manual Geofence
10 , Trip 11
Sleep modes| GPS Sleep 12 , Online Deep Sleep 13 , Deep Sleep 14 , Ultra Deep Sleep15
Configuration and
firmware update| FOTA Web 16 , FOTA 17 , Teltonika Configurator 18 (USB, Bluetooth), FMBT mobile application 19 (Configuration)
SMS| Configuration, Events, Debug
GPRS commands| Configuration, Debug
Time Synchronization| GPS, NITZ, NTP
Ignition detection| Accelerometer, External Power Voltage

SAFETY INFORMATION

This message contains information on how to operate FMM800 safely. By following these requirements and recommendations, you will avoid dangerous situations. You must read these instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed voltage range is +10…+30 V DC.
To avoid mechanical damage, it is advised to transport the device in an impact-proof package. Before usage, the device should be placed so that its LED indicators are visible. They show the status of device operation.
Before unmounting the device from vehicle, ignition MUST be OFF.

| Do not disassemble the device. If the device is damaged, the power supply cables are not isolated or the isolation is damaged, DO NOT touch the device before unplugging the power supply.
---|---
| All wireless data transferring devices produce interference that may affect other devices which are placed nearby.
| Please consult representatives of your vehicle model regarding OBDII location on your vehicle.
In case you are not sure about proper connection, please consult qualified personnel.
| The programming must be performed using a PC with autonomic power supply.
| Installation and/or handling during a lightning storm is prohibited.
| The device is susceptible to water and humidity.
| Teltonika is not responsible for any harm caused by wrong cables used for connection between PC and FMM800
| WARNING! Do not use FMM800 device if it distracts driver or causes inconvenience due to OBDII placement. Device must not interfere with driver.
| Battery should not be disposed of with general household waste. Bring damaged or worn-out batteries to your local recycling center or dispose them to battery recycle bin found in stores.

CERTIFICATION AND APPROVALS

This sign on the package means that it is necessary to read the User‘s Manual before your start using the device. Full User‘s Manual version can be found in our Wiki
This sign on the package means that all used electronic and electric equipment should not be mixed with general household waste.
1 . 1 wiki.teltonika-gps.com/view/FMM800

CHECK ALL CERTIFICATES
All newest certificates may be found in our Wiki2.
2 wiki.teltonika-gps.com/view/FMM800Certification%26_Approvals

WARRANTY

TELTONIKA guarantees its products to be free of any manufacturing defects for a period of 24 months. With additional agreement we can agree on a different warranty period, for more detailed information please contact our sales manager.
Contact us teltonika-gps.com/about-us/contacts
All batteries carry a reduced 6 month warranty period.
If a product should fail within this specific warranty time, the product can be:

Repaired
Replaced with a new product
Replaced with an equivalent repaired product fulfilling the same functionality
TELTONIKA can also repair products that are out of warranty at an agreed cost.

WARRANTY DISCLAIMER

TELTONIKA PRODUCTS ARE INTENDED TO BE USED BY PERSONS WITH TRAINING AND EXPERIENCE. ANY OTHER USE RENDERS THE LIMITED WARRANTIES EXPRESSED HEREIN AND ALL IMPLIED WARRANTIES NULL AND VOID AND SAME ARE HEREBY EXCLUDED.
ALSO EXCLUDED FROM THIS LIMITED WARRANTY ARE ANY AND ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING BUT NOT LIMITED TO, LOSS OF USE OR REVENUE, LOSS OF TIME, INCONVENIENCE OR ANY OTHER ECONOMIC LOSS.
More information can be found at teltonika-gps.com/warranty-repair