HALO HLBE6 Recessed LED Ceiling and Shower Disc Light Instruction Manual

HALO HLBE6 Recessed LED Ceiling and Shower Disc Light .

Product Usage Instructions

Wiring

1. Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1). Make sure the opening is not larger than the outer flange of the LED module.
2. Open the cover of the provided jbox and insert the supply wires through the preferred strain reliefs in the provided jbox. Connect the bare copper (ground) wire from the jbox to the ground wire of the supply connection using the provided wire nut.
3. Connect the black/white leads from the output of the driver to the appropriate supply side wiring using the provided wire nuts.

FAQ

Can I install the HLBE models directly into a ceiling without a separate JBOX or recessed housing
A: Yes, the HLBE models can be installed directly into a ceiling without requiring separate JBOX or recessed housings.
Q: Can I dim the Halo HLBE luminaire? What dimmers should I use?
A: Yes, the Halo HLBE is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low end trim adjustment. Consult the dimmer manufacturer for specific load compatibility and application information. Note that some dimmers require a neutral in the wall box.

HLBE 4”, HLBE 6” Series Instructions Instructions pour les séries HLBE 4” , HLBE 6” Instrucciones para las series HLBE 4”, HLBE 6”

Packaging Contents

A. HLBE and connector, round HLBE et connecteur, rond HLBE y conector, redondo

ITEMS REQUIRED (Purchase separately)

• Gloves
• Ladder
• Hole saw

OPTIONAL

• Drill
• Screws for mounting (if required by local code)

IMPORTANT SAFETY INSTRUCTIONS

Read and follow these instructions and heed all warnings, including those on the product. Failure to do so may result in serious bodily injury or property damage.
When using the product, basic precautions should always be followed, including the following:

• Read and follow these instructions.
• HALO recessed luminaires (fixtures) are designed to meet the latest NEC requirements and are certified in full compliance with UL. Before attempting the installation of any recessed lighting luminaire check your local electrical code. This code sets the wiring standards for your locality and should be carefully studied before starting.

SAVE THESE INSTRUCTIONS AND WARNINGS.

WARNING

Risk of Fire  MINIMUM 90°C SUPPLY CONDUCTORS. If uncertain, consult an electrician.
Risk of Electric Shock – To avoid possible electrical shock, be sure that the power supply is turned off at the fuse box or circuit breaker before installing or servicing the luminaire.
Risk of Fire/Electric Shock   LED DM Fixture installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician. Luminaire wiring and electrical parts may be damaged when drilling for the installation of an LED DM fixture. Check for enclosed wiring and components. To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.

CAUTION

Edges may be Sharp   Wear gloves while handling.

• Connect the fixture to a 120-volt, 60 Hz power source other connection voids the warranty.
• The fixture should be installed by persons with experience in household wiring or by a qualified electrician. The electrical system, and the method of electrically connecting the fixture to it, must be in accordance with the National Electrical Code and local building codes.
• Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
• Please examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit.
• This device is not intended for use with emergency exits.
• For Canada only per CSA C22.2 No. 250.1-16, retrofits for luminaire conversionThe retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction. The product must be installed by a qualified electrician. In accordance with the applicable and appropriate electrical codes. The installation guide does not supersede local or national regulations for electrical installations.

DIMMING
Halo HLBE is designed for dimming with many 120V Leading Edge (LE) and Trailing Edge (TE) phase control dimmers. Dimming capability may be enhanced with select dimmers that feature low-end trim adjustment. (Consult dimmer manufacturer for specific load compatibility and application information. Note some dimmers require a neutral in the wall box.) For the latest Halo HLBE product information, please refer to specifications online at www.cooperlighting.com
DETERMINING WHICH INSTALLATION METHOD
TO USE The HLBE models can be installed directly into a ceiling without requiring separate JBOX or recessed housings.

WARNING

Risk of Electric Shock To avoid possible electrical shock, be sure that the power supply is turned off at the fuse box or circuit breaker before installing or servicing the luminaire.

WIRING

1. Cut an opening in the ceiling by using the provided template to trace the module opening (see Figure 1). Make sure the opening is not larger than the outer flange of the LED module.
2. Open the cover of the provided box and insert the supply wires through the preferred strain reliefs in the provided box. Connect the bare copper (ground) wire from the box to the ground wire of the supply connection using the provided wire nut.
3. Connect the black/white leads from the output of the driver to the appropriate supply side wiring using the provided wire nuts.
4. Close the cover after properly securing the supply wire to the provided box on the rear of the LED module.
5. The module is ready to install into the ceiling. (See the MOUNTING section for specific instructions).

HLBE Series Instructions  www.halolighting. 

MOUNTING

1. Connect the remote driver box to the light fixture.(Figure 2)
2. Place remote driver box thru the cut-out hole and mount according to local code as required.
3. Bundle any excess wire and place into ceiling above the module according to local code as required.
4. Rotate both mousetrap springs upward to allow passage through the cutout in the ceiling
5. Continue to press the module through the cutout in the ceiling until the perimeter flange of the module is flush against the ceiling.
6. The springs will rotate back into position and hold the LED module tight to the ceiling.

Note: Do not install the driver box on top of the LED module. The driver box should be installed at least 0.25 in. (6.4mm) from the LED module.

CAUTION

Risk of pinching Do not place hands under springs during removal of the LED module.

REMOVAL

1. Simply pull down firmly on LED module until mousetrap springs release from the ceiling. Reach through the ceiling to hold mousetrap springs up and away from the ceiling as you continue to pull the module from it’s opening.
2. Disconnect wiring.

5-YEAR LIMITED WARRANTY
Limited warranty for five years, based on up to 6 hours of usage per day. Additional terms and conditions apply. For more details, please
visit : www.cooperlighting.com/warranty

FCC RULES

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off an on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
  • this device may not cause harmful interference, and
  • this device must accept any interference received, including interference that may cause undesired operation.

This device complies with ISED ICES Standard Canada ICES-005(B) / NMB-005 (B).

Cooper Lighting Solutions 1121 Highway 74 South Peachtree City, GA 30269
P : 770-486-4800
www.cooperlighting.com
Canada Sales 5925 McLaughlin Road Mississauga, Ontario L5R 1B8 P: 905-501-3000
F : 905-501-3172  2022 Cooper Lighting Solutions All Rights Reserved
Printed in China
Publication No. IL51800522

Cooper Lighting Solutions is a registered trademark.
All trademarks are property  of their respective owners.  Product availability, specifications, and compliances are subject to change without notice

HLBE4 and HLBE6 Round Ceiling Templates Modèles de plafond rond HLBE4 et HLBE6 Plantillas de techo redondo HLBE4 y HLBE6

HLBE6 – 6″ round cutout

References

• HALO | Cooper Lighting Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>