MOEN 930-005 NPT Smart Water Monitor and Shutoff Instructions

: June 14, 2024
: Moen

Table of Contents

MOEN 930-005 NPT Smart Water Monitor and Shutoff
Product Information
Product Usage Instructions
DESCRIPTION
WARRANTY
CRITICAL DIMENSIONS
SPECIFICATIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

MOEN 930-005 NPT Smart Water Monitor and Shutoff

Product Information

Specifications

Model : Flo Smart Water Monitor and Shutoff 1-1/4 Installation Spacer Kit
Models : 930-005 NPT, 930-006 Solder

Description

The Flo Smart Water Monitor and Shutoff is a device designed for well pump system installations. It is installed downstream of all treatment and filtration components to avoid debris interference.The device should also be installed after the well pump and water storage tank. If necessary to install the device prior to a waterfiltration system, a wye strainer with a 100 mesh or finer screen and blow-down port is required to catch any sediment or particles from the ground source or casing. The mesh screen in the strainermay require periodic maintenance.

Standards

The Flo Smart Water Monitor and Shutoff meets all applicable requirements referenced in the user manual.

Warranty

The product is covered by a one (1) year warranty for workmanship from the date of delivery following the original retail purchase.

Critical Dimensions

The clearance needed for the spacer and the future Flo by Moen device is as follows

7-1/2 inches straight pipe run on inlet
4-1/2 inches straight pipe run on outlet
3-13/16 inches clearance on the sides
8 inches clearance on the top
3-3/16 inches clearance on the bottom

Contact Information

For more information, please call 1-844-633-8356 or visit moen.com.

Product Usage Instructions

Installation

To install the Flo Smart Water Monitor and Shutoff, follow these steps

Measure using the spacer and tail pieces to determine the required length of the water main line.
Mark the water main line using pipe cutters.
Leave a clearance of 1/32 – 1/16 between the spacer and tailpieces to reduce potential for pinching o-rings during installation.
Install the Union Nuts onto the threaded 1-1/4 NPT Tailpieces or 1-1/4 Solder Tailpieces, depending on the model.
Attach the tailpieces to the water main line.
Place the O-Rings onto the tailpieces.
Insert the Installation Spacer between the tailpieces.
Tighten the Union Nuts to secure the device in place.

Maintenance

Periodically check the mesh screen in the wye strainer (if installed) for any sediment or particles and clean if necessary.

Product Components

The following components are included with the product

Union Nuts (x2)
Threaded 1-1/4 NPT Tailpieces (x2) or 1-1/4 Solder Tailpieces (x2)
O-Rings (x2)
Installation Spacer
An extra packet of O-Rings (x2)

FAQ

Q: What should I do if I need to install the device before a water filtration system?

A: If you need to install the device before a water filtration system, make sure to use a wye strainer with a 100 mesh or finer screen and blow-down port to catch any sediment or particles from the ground source or casing. Periodically check and clean the mesh screen in the strainer.

Q: How long is the warranty for the Flo Smart Water Monitor and Shutoff?

A: The product is covered by a one (1) year warranty for workmanship from the date of delivery following the original retail purchase.

Q: Where can I find more information about the product?

A: For more information, please call 1-844-633-8356 or visit moen.com.

DESCRIPTION

Installation Spacer kit for rough in of 900-002 1-1/4″ Flo Smart Water Monitor and Shutoff STANDARDS
Certified to NSF 61/9 & 372
Smart Home Water Security System third party certified by: IAPMO IGC-349-2017 and all applicable requirements referenced therein

WARRANTY

Moen® warrants that the product will be free from defects in materials and workmanship for a period of one (1) year from the date of delivery following the original retail purchase
Visit moen.com/customer-support/warranty for complete details and limitations

Installation Notes

Install product following the installation guide
Must be installed on accessible main water supply line (cold water line) that is 1-1/4″ diameter (can be installed on 1-1/2″ diameter or smaller)
Must be installed after water meter, water shut-off, and pressure regulating valve (if applicable)

Future Installation of 900-002 Requirements

Power supply and device must not be installed where the ambient temperature can exceed 140 deg F (60 deg C) or below 32 deg F (0 deg C)
Requires electrical outlet (100-240VAC-50/60 Hz) with continuous power within 10 feet of device
Requires WiFi network (WLAN connectivity/IEEE 802.11bgn, 2.4 GHz range)
Smartphone (iPhone or Android) with installed app required unless using local mode feature

For Well Pump System Installation
When installed on well or irrigation water service lines, the device should be placed after downstream of) all treatment and filtration components to avoid debris interference. It should also be installed after the well pump and water storage tank. If it is necessary to install the 900-002 device prior to a water filtration system, a wye strainer with a 100 mesh or finer screen and blow-down port is required to catch any sediment or particles from the ground source or casing. The mesh screen in the strainer may require periodic maintenance.

CRITICAL DIMENSIONS

SPECIFICATIONS

Flo Smart Water Monitor and Shutoff
1-1/4″ Installation Spacer Kit
Models : 930-005 NPT
930-006 Solder

NPT Tailpieces (included with 930-005)

Solder Tailpieces (included with 930-006)

The clearance needed for the spacer and the future Flo by Moen device is as followed

7-1/2″ straight pipe run on inlet
4-1/2″ straight pipe run on outlet
3-13/16″ clearance on the sides
8″ clearance on the top
3-3/16″ clearance on the bottom

Measure using the spacer and tail pieces. Mark and cut the water main line using pipe cutters. Allow space for the installation spacer and both tailpieces. To reduce potential for pinching o-rings during installation, it is recommended to leave a clearance of 1/32″ – 1/16″ between the spacer and tailpieces.

Included with 930-005 product
Union Nuts (x2), Threaded 1-1/4″ NPT Tailpieces (x2), O-Rings (x2),Installation Spacer, and an extra packet of O-Rings (x2).

Included with 930-006 product
Union Nuts (x2), 1-1/4″ Solder Tailpieces (x2), O-Rings (x2), Installation Spacer, and an extra packet of O-Rings (x2).