HORIZON HOBBY BLH01250 Eclipse 360 BNF Electric Helicopter Instruction Manual

: June 1, 2024
: HORIZON HOBBY

HORIZON HOBBY BLH01250 Eclipse 360 BNF Electric Helicopter

HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter-PRODUCT-
IMAGE

Product Information

Specifications

Length: 30.6 in (767mm)
Height: 7.6 in (193mm)
Main Rotor Diameter: 30.6 in (767mm)
Tail Rotor Diameter: 4.7 in (120 mm)
Flying Weight: 33 oz (935 g)

Components

Main Motor: Eclipse 360, (BLH01247)
Tail Motor: Eclipse 360 (BLH01248)
Receiver: SRXL2 DSMX Remote Serial Telemetry Receiver
Flight Controller: FC6250HX Helicopter Flybarless Flight Control (SPMFC6250HX)
ESC: Dual ESC 30A 15A: Eclipse 360 (SPMXAHE3015)
Swash Servos: Spektrum H3050 Mid-Torq Ultra-Speed Micro Heli Cyclic Serv
Transmitter: RFL1205
Flight Battery: SPMWS2000
Battery Charger: SPMXPSA200

Included Accessories

BNF- Basic (BLH01250)
RealFlight Trainer Edition RC Flight Simulator
WS2000 Wireless Simulator USB Dongle
Smart G2 Powerstage : 3S 2200mAh

Optional Accessories
Scan the QR code to access the product completion guide for information on the recommended Powerstage bundle as well as other compatible batteries and chargers.

Product Usage Instructions

First Flight Preparation

Always turn the transmitter on first.
Plug the flight battery into the lead from the ESC.
Allow the ESC to initialize and arm properly.
Fly the model.
Land the model.
Unplug the flight battery from the ESC.
Always turn the transmitter off last.

Safety Precautions and Warnings

WARNING: Read the ENTIRE instruction manual before operating to avoid damage to the product and personal property.
Age Recommendation: Not for children under 14 years. This is not a toy.

Special Language Meaning

WARNING: Procedures not properly followed may lead to property damage or serious injury.
CAUTION: Procedures not properly followed may result in physical property damage and a possibility of serious injury.
NOTICE: Procedures not properly followed may cause physical property damage with little or no possibility of injury.

WARNING AGAINST COUNTERFEIT PRODUCTS
If replacing a Spektrum component, purchase from Horizon Hobby, LLC or authorized dealers for authentic products and warranty support.

FAQ

Q: Where can I find the most up-to-date manual information?
A: Scan the QR code and select the Manuals and Support quick links from the product page.

Instruction Manual

Scan the QR code and select the Manuals and Support quick links from the product page for the most up-to-date manual information.

NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com or towerhobbies.com and click on the support or resources tab for this product.

Meaning of Special Language

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
WARNING : Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury. CAUTION: Procedures, which if not
properly followed, create the probability of physical property damage AND a possibility of serious injury.
NOTICE : Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.
WARNING : Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

Age Recommendation: Not for children under 14 years This is not a toy.

Safety Precautions and Warnings

Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
Always operate your model in open spaces away from full-size vehicles, traffic and people.
Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
Always keep all chemicals, small parts and anything electrical out of the reach of children.
Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.
Always engage throttle hold before approaching the aircraft.
Never place any portion of the model in your mouth as it could cause serious injury or even death.
Never operate your model with low transmitter batteries.
Always keep aircraft in sight and under control.
Always move the throttle fully down at rotor strike.
Always use fully charged batteries.
Always keep transmitter powered on while aircraft is powered.
Always remove batteries before disassembly.
Always keep moving parts clean.
Always keep parts dry.
Always let parts cool after use before touching.
Always remove batteries after use.
Never operate aircraft with damaged wiring.
Never touch moving parts.

WARNING AGAINST COUNTERFEIT PRODUCT S: If you ever need to replace a Spektrum component found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.

Specifications

Length| 30.6 in (767mm)| Tail Rotor Diameter| 4.7 in (120 mm)
Height| 7.6 in (193mm)| Flying Weight| 33 oz (935 g)
Main Rotor Diameter| 30.6 in (767mm)|
| Components| BNF- Basic (BLH01250)
---|---|---
Airframe| Blade Eclipse 360| Included
Main Motor| Main Motor: Eclipse 360, (BLH01247)| Installed
Tail Motor| Tailmotor: Eclipse 360 (BLH01248)| Installed
Receiver| SRXL2 DSMX Remote Serial Telemetry Receiver| Installed
Flight Controller| FC6250HX Helicopter Flybarless Flight Control (SPMFC6250HX)| Installed
ESC| Dual ESC 30A 15A: Eclipse 360 (SPMXAHE3015)| Installed
Swash Servos| Spektrum H3050 Mid-Torq Ultra-Speed Micro Heli Cyclic Servo| Installed
Required Equipment

Transmitter| DSM2®/DSMX® Compatible Transmitter
Flight Battery| 3S 11.1V 2200mAh – 3200mAh Smart 30C (or higher) Li- Po with IC3® (we recommend SPMX22003S30)
Battery Charger| 3S LiPo Battery Compatible (we recommend SPMXC2050)
Optional Accessories

RFL1205| RealFlight Trainer Edition RC Flight Simulator
SPMWS2000| WS2000 Wireless Simulator USB Dongle
SPMXPSA200| Smart G2 Powerstage: 3S 2200mAh

Completion Guide
Scan the QR code to go to the product completion guide for information on the recommended Powerstage bundle as well as other compatible batteries and chargers.

First Flight Preparation

Remove and inspect contents
Begin charging the flight battery
Install the flight battery in the helicopter (once it has been fully charged)
Program your computer transmitter
Bind your transmitter
Program Smart telemetry options in your transmitter
Familiarize yourself with the controls
Find a suitable area for flying

Flying Checklist

Always turn the transmitter on first
Plug the flight battery into the lead from the ESC
Allow the ESC to initialize and arm properly
Fly the model
Land the model
Unplug the flight battery from the ESC
Always turn the transmitter off last

NX and DX Series Transmitter Setup

Power ON your transmitter, click on scroll wheel, roll to System Setup and click the scroll wheel. Choose yes.
Go to Model Select and choose at the bottom of the list. The system asks if you want to create a new model, select Create
Set Model Type: Select Helicopter Model Type by choosing the Helicopter. The system asks you to confirm model type, data will be reset. Select YES
Scroll down and select Model Name: Input a name for your model file
Scroll up to BACK and press the scroll wheel to return to System Setup
Scroll down and select F-Mode Setup
Set to:
Switch 1: Switch B
Hold Switch: Switch H
Scroll up to LIST and press the scroll wheel to return to System Setup
Scroll down and select Channel Assign
Scroll down on the Channel input config screen and set Ch 5 Gear to F-Mode
Scroll up to LIST and press the scroll wheel to return to System Setup
Select
, Click the scroll wheel to enter the Function List
Scroll down to Rates and Expo and press the scroll wheel
- Scroll down to Channel and select Aileron
- Set Switch: Switch F
- Move Switch F to the O position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch F to the 1 position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch F to the 2 position
- Set Low Rates: 75%/75%, Expo 25%/25%
Scroll up to Channel and select Elevator
- Set Switch: Switch F
- Move Switch C to the O position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch C to the 1 position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch C to the 2 position
- Set Low Rates: 75%/75%, Expo 25%/25%
Scroll up to Channel and select Rudder
- Set Switch: Switch F
- Move Switch C to the O position
- Set High Rates: 100%/100%, Expo 45%/45%
- Move Switch C to the 1 position
- Set High Rates: 100%/100%, Expo 45%/45%
- Move Switch C to the 2 position
- Set Low Rates: 75%/75%, Expo 45%/45%
Scroll up to LIST and press the scroll wheel to return to the Function List
Scroll down to Throttle Curve and press the scroll wheel Scroll to the N box for curve selection and press the scroll wheel to select the Normal curve
Set the Curve values to
Scroll to the #1 box for curve selection and press the scroll wheel to select the Stunt #1 curve Set the Curve values to
Scroll to the #2 box for curve selection and press the scroll wheel to select the Stunt #2 curve Set the Curve values to
Scroll to the H box for curve selection and press the scroll wheel to select the Hold curve Set the Curve values to
Scroll down to Pitch curve and press the scroll wheel Scroll to the N box for curve selection and press the scroll wheel to select the Normal curve Set the Curve values to
Scroll to the #1 box for curve selection and press the scroll wheel to select the Stunt #1 curve Set the Curve values to
Scroll to the #2 box for curve selection and press the scroll wheel to select the Stunt #2 curve Set the Curve values to
Scroll to the H box for curve selection and press the scroll wheel to select the Hold curve Set the Curve values to
Scroll up to LIST and press the scroll wheel to return to the Function List
Scroll down to Mixing and press the scroll wheel
- Select Mix 1, Select Normal
- Select the first INH (for master) and select the I switch
- Select the second INH (for slave) and select the Gear Channel
- Set the first Rate value to 0% the second to -125%
- Set the Offset to 100
- Set the Switch to the I button
Scroll up to LIST and press the scroll wheel to return to the Function List
Scroll down to Timer and press the scroll wheel
Set to;
Mode: Count Down
Time: 5:00
Start: Throttle Out
Over: 25%
One Time: Inhibit
Scroll up to LIST and press the scroll wheel to return to the Function List
Scroll up to
and press the scroll wheel See the Smart Throttle section for information on telemetry setup

iX Series Transmitter Setup

Power ON your transmitter and begin once the Spektrtum Airware app is open. Select the orange pen icon in the upper left corner of the screen, the system asks for permission to Turn Off RF, select PROCEED
Select the three dots in the upper right corner of the screen, select Add a New Model
Select Model Option, choose DEFAULT, select Helicopter.
The system asks if you want to create a new Heli model, select Create
Select the last model on the list, named Heli.
Tap on the word Acro and rename the file to a name of your choice
Tap and hold the back arrow icon in the upper left corner of the screen to return to the main
Tap on the Model Setup button
Set Flight Mode Setup
- Switch 1: Switch B
- Hold Switch: Switch H
- Tap on the arrow in the upper left corner to return to the Model Setup menu
Set Channel Assign
- Set Channel input config: set Ch 5 Gear to Flight Mode
- Tap on the arrow in the upper left corner to return to the Model Setup menu Tap on the arrow in the upper left corner to return to the main screen
Tap on the Model Adjust button
Tap on Dual Rates and Exponential;
- Tap on the pull down tab at Channel and select Aileron
- Set Switch: Switch F
- Move Switch F to the O position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch F to the 1 position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch F to the 2 position
- Set Low Rates: 75%/75%, Expo 25%/25%
Tap on the pull down tab at Channel and select Elevator
- Set Switch: Switch F
- Move Switch C to the O position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch C to the 1 position
- Set High Rates: 100%/100%, Expo 25%/25%
- Move Switch C to the 2 position
- Set Low Rates: 75%/75%, Expo 25%/25%
Tap on the pull down tab at Channel and select Rudder
- Set Switch: Switch F
- Move Switch C to the O position
- Set High Rates: 100%/100%, Expo 45%/45%
- Move Switch C to the 1 position
- Set High Rates: 100%/100%, Expo 45%/45%
- Move Switch C to the 2 position
- Set Low Rates: 75%/75%, Expo 45%/45%
Tap on the arrow in the upper left corner to return to the Model Adjust menu
Tap on Throttle curve
- Ensure Switch H is set to the O position
- Set the B switch to the 0 position to select the Normal curve Set the Curve values to
Set the B switch to the 1 position to select the Stunt #1 curve Set the Curve values to
Set the B switch to the 2 position to select the Stunt #2 curve Set the Curve values to
Set the H switch to the 1 position to select the Hold curve Set the Curve values to
Tap on the arrow in the upper left corner to return to the Model Adjust menu
Tap on Pitch curve
- Ensure Switch H is set to the O position
- Set the B switch to the 0 position to select the Normal curve Set the Curve values to
Set the B switch to the 1 position to select the Stunt #1 curve Set the Curve values to
Set the B switch to the 2 position to select the Stunt #2 curve Set the Curve values to
Set the H switch to the 1 position to select the Hold curve Set the Curve values to
Tap on the arrow in the upper left corner to return to the Model Adjust menu
Tap on Mixing
- Select P-Mix 1, Select Normal
- Select the first INH (for master) and select the I switch
- Select the second INH (for slave) and select the Gear Channel
- Set the first Rate value to 0% the second to -125%
- Set the Offset to 100
- Set the Switch to the I button
Tap on in the upper right corner to return to the Mixing menu
Tap on the arrow in the upper left corner to return to the Model Adjust menu
Tap on the arrow in the upper left corner to return to the main screen
Tap on the clock icon in the Timer 1 box
- Set to;
- Mode: Count Down
- Time: 5:00
- Switch: Throttle Out
- Over Under Trigger: 25%
- One Time: Inhibit
Tap on the arrow in the upper left corner to return to the main screen

See the Smart Throttle section for information on telemetry setup

Installing the Flight Battery

$HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $3$$

Lower the throttle.
Power on the transmitter.
Center all trims.
To allow the ESC to arm and to keep rotors from initiating at startup, turn on throttle hold and normal flight mode before connecting the flight battery.
Attach hook material to the helicopter frame and loop material to the battery.
Install the flight battery on the helicopter frame. Secure the flight battery with the hook and loop straps.
CAUTION: Make sure the flight battery, wire and connector does not come into contact with the motor. Failure to do so will cause the motor, ESC and battery to overheat, resulting in a crash causing property damage and injury.
Bind your transmitter to the helicopter to establish a connection. See the Binding section below for more information.
Connect the battery cable to the ESC. The swashplate will center, indicating that the unit is ready. The flight controller status LED will display a slow green flash once initialization has been completed.
The helicopter motor will emit a series of tones, indicating the ESC is armed.
CAUTION: Always disconnect the Li-Po battery from the ESC power lead when not flying to avoid over-discharging the battery. Batteries discharged below the lowest approved voltage may become damaged, resulting in loss of performance and potential fire when batteries are charged.

Transmitter and Receiver Binding

Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifier) code of a single specific transmitter. You need to ‘bind’ your chosen Spektrum™ DSM2®/DSMX® technology equipped aircraft transmitter to the receiver for proper operation. The receiver on the Eclipse 360 Smart helicopter is located on the bottom frame tray. The bind button is located in the center of the case, off to one side, with the Spektrum logo (bars) on the surface of the button. $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF- 0Electric-Helicopter- $4$$

Your BNF aircraft must be bound to your transmitter to establish a connection, follow the directions below.

Program your transmitter using the Transmitter Setup found in this manual.
Lower the throttle stick to the lowest position, change the flight mode to normal mode (stability mode) and activate throttle hold. Set all trims to the center position.
Power off the transmitter, or power off the RF signal if using a Spektrum NX or iX series transmitter.
Connect the flight battery to the ESC.
Press the bind button on the remote receiver to initiate binding. The orange LED on the receiver will begin flashing rapidly to indicate bind mode.
Follow the procedures of your specific transmitter to enter bind mode. The system will connect within a few seconds. Once connected, the orange LED on the receiver will come on solid orange.
Disconnect the flight battery and power off your transmitter (or power off RF for iX series Spektrum transmitters).

If you encounter problems, obey binding instructions and refer to transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office.
LED Indicator on Flight Controller

Indicator Description

Slow Green Flash| Ready to Fly
Slow Red Flash| Failsafe Active
Slow Cyan Flash| Forward Programming Mode
Yellow Flash (during calibration)| Calibration proceeding normally
Red Flash (during calibration)| Calibration Error, FC not level or is being moved during calibration

Smart Throttle

The ESC in this helicopter paired with the FC6250HX flight controller and the 4651T receiver enables the use of Smart technology. This system can provide a variety of real-time power system related telemetry data while you fly, including motor RPM, current, battery voltage and more to compatible Spektrum AirWare™ equipped transmitters.
During binding your transmitter will perform an auto configuration which will populate the telemetry page. You may need to change the telemetry values to suit this aircraft and your needs.
To enter the telemetry values:
(For iX series transmitters, you must select Save on each page)

Power on your transmitter.
Set the throttle hold to on.
Power on the aircraft and allow it to initialize.
In your transmitter, go to the Function List (Model Setup in iX series transmitters).
Select the Telemetry menu option.
Go to the Smart Battery menu option.
Scroll down to Startup Volts, enter 4.0V/cell.
Return to the Telemetry menu.
Go to the Smart ESC menu option.
Scroll down to Total Cells, enter 3.
Scroll down to Low Voltage Alarm, enter 3.2V/Cell and set to Voice.
Scroll down to Poles, enter 8.
Scroll down to Ratio, enter 9.64:1
Return to the main screen.

Technology

Revolutionary SAFE® (Sensor Assisted Flight Envelope) technology uses an innovative combination of multi-axis sensors and software that allows model aircraft
to know its position relative to the horizon. This spatial awareness is utilized to create a controlled flight envelope the aircraft can use to maintain a safe region of bank and pitch angles so you can fly more safely. Far beyond stability, this level of protection offers multiple modes so the pilot can choose to develop his or her skills with a greater degree of security and flight control that always feels crisp and responsive.
Flight Mode and Rate Selection

Revolutionary SAFE® (Sensor Assisted Flight Envelope) technology uses an innovative combination of multi-axis sensors and software that allows model aircraft to know its position relative to the horizon. This spatial awareness is utilized to create a controlled flight envelope the aircraft can use to maintain a safe region of bank and pitch angles so you can fly more safely. Far beyond stability, this level of protection offers multiple modes so the pilot can choose to develop his or her skills with a greater degree of security and flight control that always feels crisp and responsive.
Flight Mode and Rate Selection
- B Switch
- 0 = Normal, SAFE Stability
- On 1 = Stunt 1, SAFE Stability Off
- 2 = Stunt 2, SAFE Stability Off

SAFE technology delivers:

Flight envelope protection you can enable at the flip of a switch.
Multiple modes let you adapt SAFE technology to your skill level instantly.

Best of all, sophisticated SAFE technology doesn’t require any work to enjoy. Every aircraft with SAFE installed is ready to use and optimized to offer the best possible flight experience.
Change control rates in any mode by moving the rate switch (Switch F).

Low rate (switch position 2) reduces the control rates, making the model easier to control. Beginners should use low rate for initial flights.
High rate (switch positions 0 and 1) provides full control and should be used by intermediate and experience pilots.

Panic Recovery

If you get into distress while flying in any mode, activate the panic function and move the control sticks to their neutral position. SAFE technology will immediately return the aircraft to an upright level attitude, if the aircraft is at a sufficient height with no obstacles in its path. Return the collective stick to 50% and deactivate the Panic Recovery function to return to the current flight mode.

Panic Mode Operation
Bind / I Button
- Pressed = Panic Mode On
- Released = Panic Mode Off
NOTICE: Before deactivating Panic Recovery , make sure the collective stick has been returned to the 50% position. Once the Panic Recovery has been deactivated, full negative collective becomes available, which could cause the Eclipse 360 Smart to descend rapidly.
- This mode is intended to provide the pilot with the confidence to continue to improve their flight skills.
- Move the collective stick to 50% and return all other transmitter controls to neutral for the quickest recovery.
- Once the model has reached a level upright attitude, the negative collective is reduced to prevent the user from pushing the model into the ground.

Throttle Hold

Throttle hold only turns off the motor on an electric helicopter. You maintain pitch and direction control.
The blades will spin if throttle hold is OFF. For safety, turn throttle hold ON any time you need to touch the helicopter or check the direction controls.
Throttle Hold Operation

H Switch
0 = Motor operates normally
1 = Throttle hold is ON, motor will not spin
Throttle hold is also used to turn off the motor if the helicopter is out of control, in danger of crashing, or both.

Control Tests

CAUTION: You must complete the Cyclic tests prior to every flight. Failure to complete the tests and ensuring the sensor corrects in the proper direction can cause the helicopter to crash, resulting in property damage and injury.

Cyclic
It is normal for the swashplate to slowly move back to its original position after a stick input and for the servos to not move at the same speed as your control sticks.
- Tilt the helicopter forward. The swashplate must tilt backward.
- Tilt the helicopter backward. The swashplate must tilt forward.
- Roll the helicopter left. The swashplate must roll right.
- Roll the helicopter right. The swashplate must roll left.

Cyclic and Collective Control Test

Ensure the throttle hold is ON when performing the direction control tests. Test the controls prior to each flight to ensure the servos, linkages and parts operate correctly. If the controls do not react as shown in the illustrations below, confirm the transmitter is programmed correctly before continuing on to the Motor Test.

Elevator/ Fore and aft cyclic

$HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $6$$

Aileron/ Left and right cyclic $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF- 0Electric-Helicopter- $7$$

Collective Pitch $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric- Helicopter- $8$$

Motor Test

Place the helicopter outdoors on a clean, flat and level surface (concrete or asphalt) free of obstructions. Always stay clear of moving rotor blades.

WARNING: The motor will spin when throttle is increased while throttle hold is OFF.

Check the swashplate directions to ensure they are moving in the correct direction. Please refer to the diagrams on the prior page for reference.
WARNING: Stay at least 30 feet (10 meters) away from the helicopter when the motor is running.
Do not attempt to fly the helicopter at this time.
Ensure the throttle is lowered completely and is in normal flight mode.
Turn throttle hold off.
Slowly increase the throttle until the blades begin to spin. The main blades spin clockwise when viewing the helicopter from the top. The tail rotor blades spin counterclockwise when viewing the helicopter from the right-hand side.
Turn throttle hold on.

Low Voltage Cutoff (LVC)

The ESC will continuously lower power to the motor until complete shutdown when the battery reaches 9V under load. This helps prevent over-discharge of the Li-Po battery. Land immediately when the ESC activates LVC. Continuing to fly after LVC can damage the battery, cause a crash or both. Crash damage and batteries dam-aged due to over-discharge are not covered under warranty.
Understanding the Primary Flight Controls

Repeatedly flying the helicopter until LVC activates will damage the helicopter battery.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. During storage, make sure the battery charge does not fall below 3V per cell.

If you are not familiar with the controls of your Eclipse 360, take a few minutes to familiarize yourself with them before attempting your first flight.

$HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $9$$ $HORIZON-HOBBY- BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $10$$

Pre-Flight Checklist

Check all screws and ensure that they are tight
Check main and tail blades to ensure they are not damaged
Check all links and make sure they move freely but do not pop off easily
Check that flight battery and transmitter battery are fully charged
Check all wires to ensure that they are not cut, pinched, or chaffed and are properly secured
Check all wire connections
Check gears and make sure no teeth are missing
Do a complete control test
Verify the receiver sensor is correcting in the proper directions
Check that servos are functioning properly
Check to make sure the flight battery is properly secured
Check to make sure all electronic components are properly secured

Flying the Blade Eclipse 360 Helicopter

Consult local laws and ordinances before choosing a location to fly your aircraft.
Select a large, open area away from people and objects. Your first flights should be outdoors in low-wind conditions. Always stay at least 30 feet (10 meters) away from the helicopter when it is flying.
The Blade Eclipse 360 is intended to be flown outdoors by intermediate to experienced pilots.
Takeoff
The Eclipse 360 ESC utilizes a soft start function. Raise the throttle / collective stick to mid stick and the head speed will slowly begin to increase RPM. Once the head speed is consistant (spool up takes approximately 10 seconds), raise the throttle / collective stick slowly until the model lifts off from the ground. Establish a hover at least 24” (0.6 meter) high, outside of ground effect.
CAUTION: Making large inputs to the roll or pitch controls while the helicopter is on the ground may result in a crash.

Flying

First flights should be performed in normal mode and low cyclic and tailrotor rates until you are familiar with the flying manner of the helicopter.

CAUTION: Always fly the helicopter with your back to the sun and the wind to prevent loss of flight control.

Landing
Establish a low level hover. Deliberately lower the throttle until the helicopter lands.
When the helicopter is in stunt mode:
- The rotor head speed is constant.
- The main rotor will increase negative pitch as the throttle/collective stick is moved from the middle stick position to the low stick position. Negative pitch allows the helicopter to fly upside down and perform aerobatics.
- Change between normal and stunt modes in a hover with the throttle near the hovering stick position.
- WARNING: Do not use wooden main blades with the Blade Eclipse 360 or injury and/or property damage could occur. Only use Blade Eclipse 360 replacement main blades.

Removing the Mechanics From the Fuselage

To remove the mechanics from the fuselage:

Remove the four tail motor mount screws.
Remove the two screws on the side of the fuselage and the six screws from the bottom of the fuselage.
Remove the lower hatch from the fuselage.
Unplug lights from wiring harness.
Partially remove the mechanics with tail boom from the fuselage.
Remove tail motor assembly from the fuselage
Disconnect the tail motor
Complete removal of the mechanics and tail boom from the fuselage.

To reinstall the fuselage:
Repeat in reverse order.

Post-Flight Inspections and Maintenance

Ball Links| Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail.
---|---
Cleaning| Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry lint free cloth.
Bearings| Replace bearings when they become damaged.
Wiring| Make sure wiring does not block moving parts. Replace damaged wiring and loose connectors.
Fasteners| Make sure there are no loose screws, other fasteners or connectors. Do not over tighten metal screws in plastic parts. Tighten screw so parts are mated together, then turn screw only 1/8th of a turn more.
Rotors| Make sure there is no damage to rotor blades and other parts which move at high speed. Damage to these parts includes cracks, burrs, chips or scratches. Replace damaged parts before flying.
Flight Controller| Make sure the flight controller is securely attached to the frame. Replace the double-sided tape when necessary. The helicopter will crash if the flight controller separates from the helicopter frame.

Advanced Tuning (Forward Programming)

The following applies to forward programming capable Spektrum transmitters. Consult your transmitter manual or visit SpektrumRC.com for a complete list of forward programming capable transmitters.
The Blade Eclipse 360 default settings are appropriate for most users. We recommend flying with the default parameters before making any adjustments.
The Blade Eclipse 360 BNF flight controller may be programmed from any compatible Spektrum transmitter (visit SpektrumRC.com for more information).
The flight controller shipped with BNF models is specifically configured for the Blade Eclipse 360 Helicopter utilizing the supplied electronic components and is not intended for use in other aircraft.
Entering the Advanced Parameters Menu
With the helicopter bound to the transmitter and powered on, enter the Function List and select Forward Programming. Make small changes to one parameter at a time and test fly the changes before changing the parameter further or changing a different parameter. If at anytime you want to restore the default value for a parameter simply press the [RESET] button on IX radios screen or the [Clear] button on DX and NX transmitters and the default value for that parameter will be restored to the recommended value for your specific BNF model.

Calibration Procedure
If the helicopter is experiencing drift issues, perform the following calibration. The calibration procedure may also be needed following crash repairs.

Ensure the surface used for calibration is level.
Power on the transmitter and activate throttle hold.
Connect the flight batter to the ESC and allowing the model to initialize. Turn Throttle Hold ON.
Use a small 2 axis bubble level on the motor as shown below. $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $12$$
Level the helicopter placing a shim under the landing skid if necessary. $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $13$$
Enter the Function List on your transmitter.
Select Forward Programming.
Select System Setup.
Select Calibration.
Select Apply and the calibration will begin. The LED will flash yellow indicating the calibration is proceeding normally. If the LED changes to red this indicates the model is not near level or the model was moved, in this case the calibration starts over.
After the calibration is successfully completed, the receiver LED will will change to a slow cyan flash which indicates the calibration has completed.
Exit forward programming and proceed to the pre-flight check list procedure before flying your model.

Factory Reset

If the process of changing parameters on the the Blade Eclipse 360 helicopter results in undesirable flight performance, you can reset the settings back to factory defaults by selecting the Factory Reset option in Forward Programming.

Enter the Function List
Select Forward Programming
Select System Setup
Select Factory Reset
Select Apply
Perform the Setup->Swashplate->Sub Trim function and ensure the servos are properly trimmed.
Proceed with the pre-flight check list procedure before flying the model.

Trim Flight

Perform this procedure if the model is not performing well or has been recently rebuilt from a crash.
The trim flight procedure was performed during the factory test flight and only needs to be performed if you notice the model is not returning to level consistently or if the model does not remain still during stationary pirouettes.
The trim flight is used to determine the optimal settings for SAFE® technology during flight.
The trim flight must be performed in calm conditions.

Entering Trim Flight Mode

Lower the throttle stick to the lowest position.
Center all trims.
Power ON the transmitter.
Install the flight battery in the helicopter.
Connect the battery connector to the ESC.
Place the helicopter on a flat surface and leave it still until the motor beeps twice and the blue ESC LED glows solid, indicating initialization is complete.
Place the helicopter where you are going to take off.
Move and hold the left stick to the bottom left corner and the right stick to the top left corner as shown.
Activate Panic Recovery until the swashplate rotates around once.
Release the sticks and deactivate panic recovery.
The model is ready for the trim flight.

Performing the Trim Flight

Slowly increase the throttle to lift the model into a stationary hover. Make corrections as necessary to keep the model still. Evaluation does not begin until the throttle stick is over 50% and the sticks are centered. Making corrections will not affect the result but a longer flight may be necessary.
Keep the model stationary in a hover for 120 seconds. Sliding and slow movements are okay. The main goal is to keep the rotor disk level.
Once you are satisfied with the trim flight, land the model.

Exiting Trim Flight Mode

After landing, lower the throttle stick to the lowest position.
Activate Panic Recovery for 2 seconds, or until the swashplate moves, indicating the servo positions and attitude values have been recorded and trim flight mode has been exited.

Flight Test
After performing the trim flight, test-fly the model to evaluate the leveling characteristics.

The model should return to level flight consistently.
During takeoff, the model should lift off with minimal corrections.
During a hover, the control stick should remain close to center. Small corrections are acceptable.

If the model performs poorly or does not level properly after the trim flight, retry the entire trim flight procedure. If the problem persists, inspect the model for dam-aged components, a bent shaft or anything that may result in increased vibration. The trim flight may not record the correct values due to excessive vibration, flying in wind or the model not staying level. In these cases, shorter trim flights may be necessary. If you are still experiencing problems after several attempts please perform the calibration procedure and try the trim flight procedure again.

FC6250HX Slot Assignments
Use the following diagram if you need to replace any of the servos.

$HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $15$$

Troubleshooting Guide

| |
---|---|---
Problem| Possible Cause| Solution
Helicopter will not bind to the transmitter (during binding)| Low flight battery or transmitter battery voltage| Fully charge or replace the flight battery and/or transmitter batteries
receiver is not in bind mode| Make sure the bind plug is connected to the receiver BND/DAT port
Transmitter is not in bind mode| Power on the transmitter while holding the Trainer/Bind switch. Hold the Trainer/ Bind switch until binding is complete
Transmitter too close to the helicopter during binding process| Power off the transmitter. Move the transmitter further away from the helicopter. Disconnect and reconnect the flight battery to the helicopter and follow binding instructions

Helicopter will not link to the transmitter (after binding)

| Helicopter is bound to a different model memory (ModelMatch™ radios only)| Disconnect the flight battery. Select the correct model memory on the transmitter Reconnect the flight battery
Flight battery/Transmitter battery charge is too low| Replace or recharge batteries

SPMFC6250HX will not initialize

| The transmitter is powered off| Power on the transmitter
Controls are not centered| Center elevator, aileron and rudder controls. Make sure the throttle is at idle
Helicopter will not respond to the throttle but responds to other controls| Throttle not at idle and/or throttle trim is too high| Lower the throttle stick and lower the throttle trim
The transmitter is not in normal mode or throttle hold is on| Make sure the transmitter is in normal mode and throttle hold is off
The motor is not connected to the ESC or the motor wires are damaged| Connect the motor wires to the ESC and check motor wires for damage
Flight battery charge is too low| Replace or recharge flight battery
Throttle channel is reversed| Reverse the throttle channel on the transmitter
Helicopter power is lacking| Flight battery has low voltage| Fully charge the flight battery
Flight battery is old or damaged| Replace the flight battery
Flight battery cells are unbalanced| Fully charge the flight battery, allowing the charger time to balance the cells
Excessive current is being drawn through the BEC| Check all servos and the helicopter motor for damage
**** Helicopter will not lift off| Main rotor head is not spinning in the correct direction| Make sure the main rotor head is spinning clockwise. Refer to the motor control test
Transmitter settings are not correct| Check throttle and pitch curve settings and pitch control direction
Flight battery has low voltage| Fully charge the flight battery
Main rotor blades are installed backwards| Install the main rotor blades with the thicker side as the leading edge
The helicopter tail spins out of control| Rudder control and/or sensor direction reversed| Make sure the rudder control and the rudder sensor are operating in the correct direction
The helicopter wobbles in flight| Cyclic gain is too high| Please review the Advanced Settings – Gain Adjustments section
Headspeed is too low| Increase the helicopter’s head speed via your transmitter settings and/or using a freshly charged flight pack
Dampers are worn| Replace the main rotor head dampers

Limited Warranty

What this Warranty Covers—Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered—This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy—Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability—HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBIL-
ITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law—These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services —Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the
Warranty and Service Contact Information toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services —If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/service-center_render-service-center. If you do not have internet access, please contact Horizon Product Sup-port to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: Do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements— For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service—Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.

Warranty and Service Contact Information

| | |
---|---|---|---
Country of Purchase| Horizon Hobby| Contact Information| Address
United States of America| Horizon Service Center (Repairs and Repair Requests)| servicecenter.horizonhobby.com/RequestForm/| 2904 Research Rd Champaign, Illinois, 61822 USA
Horizon Product Support (Product Technical Assistance)| productsupport@horizonhobby.com
800-338-4639
Sales| websales@horizonhobby.com
800-338-4639
Europe Union| Horizon Technischer Service| service@horizonhobby.de| Hanskampring 9 D 22885 Barsbüttel, Germany
Sales: Horizon Hobby GmbH| +49 (0) 4121 2655 100

For the most up-to-date customer service contact information, please visit: www.horizonhobby.com/content/service-center-render-service- center

Important Federal Aviation Administration (FAA) Information

Use the QR code below to learn more about the Recreational UAS Safety Test
(TRUST), as was introduced by the 2018 FAA Reauthorization Bill. This free test is required by the FAA for all recreational flyers in the United States. The completed certificate must be presented upon request by any FAA or law enforcement official.
If your model aircraft weights more than .55lbs or 250 grams, you are required by the FAA to register as a recreational flyer and apply your registration number to the outside of your aircraft. To learn more about registering with the FAA, use the QR code below. $HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $17$$

FCC and Canada Compliance Information

FCC ID : BRWQSTLMRX2
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and/or antenna and your body (excluding fingers, hands, wrists, ankles and feet). This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Supplier’s Declaration of Conformity
This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.

Horizon Hobby, LLC
2904 Research Rd., Champaign, IL 61822

Email: compliance@horizonhobby.com
Web: HorizonHobby.com

IC Information

CAN ICES-3 (B)/NMB-3(B)
Contains IC: 6157A-KATY1T
IC: 6157A-QSTMRX2
This device contains license-exempt transmitter(s)/receivers(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following 2 conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Compliance Information for the European Union

EU Compliance Statement:
Blade Eclipse 360 BNF Basic (BLH01250) Hereby, Horizon Hobby,
LLC declares that the device is in compliance with the following: EU Radio Equipment Directive 2014/53/EU; RoHS 2 Directive 2011/65/EU; RoHS 3 Directive – Amending 2011/65/EU Annex II 2015/863.
The full text of the EU declaration of conformity is available at the following inter-net address: https://www.horizonhobby.com/content/support-render-compliance.
NOTE: This product contains batteries that are covered under the 2006/66/EC European Directive, which cannot be disposed of with normal household waste. Please follow local regulations.

Wireless Frequency Range and Wireless Output Power:

Receiver:
- 2402.0–2478.0MHz
- 18.87dBm
EU Manufacturer of Record: Horizon Hobby, LLC 2904 Research Road Champaign, IL 61822 USA
EU Importer of Record: Horizon Hobby, GmbH Hanskampring 9
22885 Barsbüttel Germany
WEEE NOTICE:

This appliance is labeled in accordance with European Directive 2012/19/EU concerning waste of electrical and electronic equipment (WEEE). This label indicates that this product should not be disposed of with household waste. It should be deposited at an appropriate facility to enable recovery and recycling.

Exploded View

$HORIZON-HOBBY-BLH01250-Eclipse-360-BNF-0Electric-Helicopter- $27$$

©2023 Horizon Hobby, LLC.
Blade, the Blade logo, SAFE, The SAFE logo, DSM2, DSMX, BNF, the BNF logo, IC3, and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
All other trademarks, service marks or logos are property of their respective owners.
US 9,930,567. US 10,419,970. US 10,849,013. CN201721563463.4. Other patents pending. 533908
BLH01250
Created 09/23

Parts List

| | | | |
---|---|---|---|---|---
#| Part #| English| | | ****
1| BLH01201| Main Blade Grips (2): Eclipse 360|
2| BLH01202| Spindle (2): Eclipse 360|
3| BLH01203| Main Body: Eclipse 360|
4| BLH01204| Main Frame: Eclipse 360|
5| BLH01205| Hatch: Eclipse 360|
6| BLH01206| Tailboom: Eclipse 360|
7| BLH01207| Tail Motor Mount: Eclipse 360|
8| BLH01208| Tailrotor: Eclipse 360 (2)|
9| BLH01209| 14t Pinon: Eclipse 360|
10| BLH01210| Main Gear Housing: Eclipse 360|
11| BLH01247| Main Motor: Eclipse 360|
12| BLH01248| Tailmotor: Eclipse 360|
13| BLH01249| Tail Extension Lead: Eclipse 360|
14| BLH1607| 1.4x4x2 Bearing (4)|
15| BLH1608| Dampeners 80 (4): B450|
16| BLH1616| Main Rotor Blade Mounting Screw & Nut (2):B450|
17| BLH1632| Washout Ctrl Arm Link Set: B450|
18| BLH1633| Alum & Comp Swashplt: B450, B400|
19| BLH1634| Anti-RotBrckt/Guide: B450, B400|
20| BLH1637| Ball Link Set (20): B450, B400|
21| BLH1640| ElevatorCtrlLeverSt: B450, B400|
22| BLH1641| 5x8x2.5 Bearing (2)|
23| BLH1642| 5x10x4 Bearing (2)|
24| BLH1643| Alum Motor Mount Set: B450, B400|
25| BLH1644| Hook&LoopBattStrap: B450, B400|
26| BLH1666| 2x5x2.5 Bearing (4)|
27| BLH1676| Servo Arm Set: B450, B400|
28| BLH4301| Flybarless Linkage Set: B450 X|
29| BLH4303| Main Rotor Grip FBL Control Balls (2):B450X|
30| BLH4322| Alu FBL Head Block Set: B450 X|
31| BLH4331| FBL Follower Arms: B450 X|
32| BLH4338| FBL LnkageRd/Pshrd St: B450 X|
33| BLH4347| Flybarless Mainshaft (2): B450 X|
34| BLH5201| Fusion 350mm Main Blade|
35| BLH5337| Helical Main Gear, 135T|
36| SPM4651T| SRXL2 Serial Telemetry Receiver|
37| SPMFC6250HX| FC6250HX Helicopter FBL System|
38| SPMSH3050| H3050 M-T / U-S MicroCyclicServ|
39| SPMSP2052| Case Set: H3050, H3060|
40| SPMXAHE3015| Dual ESC 30A 15A: Eclipse 360|

Optional Parts

| | | |
---|---|---|---|---
Part #| English|
BLH4317A| Alu FBL Main Rtr Grp Set: B450 X|
BLH4331A| Alu FBL Follower Arms: B450 X|

Recommended Components

| | | |
---|---|---|---|---
Part #| English| | | ****
SPMX22003S100| 2200mAh 3S 11.1V Smart 100C; IC3|
SPMX22003S30| 2200mAh 3S 11.1V Smart 30C; IC3|
SPMX22003S50| 2200mAh 3S 11.1V Smart 50C; IC3|
SPMXC1020| Smart S120 USB-C Charger, 1×20|
SPMXPSA200| Smart G2 Air Powerstage 2|