Sharkward BRl810-B-D Line Voltage Microwave Bi-level Sensor Instructions
- June 4, 2024
- Sharkward
Table of Contents
Sharkward BRl810-B-D Line Voltage Microwave Bi-level Sensor
SPECIFICATIONS
Dimensions
NOTE: The high-frequency output of this sensor is <0. 2mW-that is just one 5000th of the transmission power of a mobile phone or the output of a microwave oven.
SENSOR COVERAGE
Once powering the device up, the BRl810-B-D will use factory default parameters to operate.
WARNING
NOTE: Warm-up time is 15 seconds. After the sensor connects the input to
power the first time, the light will keep on 15 seconds, then go to dimming to
work normally.
NOTE: Factory Default Setting: 100% sensitivity, Hold on time: 1
0seconds, Daylight sensor is 30lux, Dimming level:30%,Dimming time:
60minitues.
NOTE: Any setting changed by DIP Switch or remote control, the led light
that sensor connect will on/off as confirmed.
UTILIZING FIELD AND INTRODUCTION
BRl810-B-D is a moving object sensor that can detect a range of 360 ° and it’ s working frequency is 5. 8GHz. The advantage of this product is stable working state (stable working temperature: -40°C~+ 70°C), BRl810-8 adopts a microwave sensor(high-frequency output<0.2mW), so that it is safe and performs better than the infrared sensor.
FUNCTION AND OPTIONS
The microwave sensor to achieve tri-level dimming control, for some areas that require a light change notice before switching off. If offers 3 levels of light Control: 100%–dimming light (0,10%,30%,50%)–off; and 2 periods of selectable waiting time: motion hold-time and standby time. Selectable daylight threshold and choice of detection area.
- With sufficient natural light, the light does not switch on when presence is detected.
- With insufficient natural light, the sensor switches on the light automatically when a person enters room.
- People left, light still dims to 0/10%/30%/50% (option s) after stand-by lime elapsed. standby level
- Light switches off automatically after t h e hold time
WIRING DIAGRAMS
Wiring with dimming ballast or LED driver
Wiring with non-dimming ballast or LED driver.
PARAMETER SETTING BY DIP SWITCH
Consider the picture: 1, 2 set sensitivity; 3, 4 set hold time; 5, 6 set the lux; 7, 8 stand-by light level ; 9, 1 O set stand-by time
Detection Range Setting (sensitivity)
Detection range is the term used to describe the radii of the more or less
circular detection zone produced on the ground after mounting the sensor light
at a height of 8-20ft, pull the switch to the ON position as” “, pull the
switch to the OFF position as “ “, switch location and detection range of the
corresponding table is as follows:
Hold Time Setting
The light can be set to stay ON for any period of time between approx.10sec
and a maximum of 15min. Any movement detected before this time elapses will
re-start the timer. It is recommended to select the shortest time for
adjusting the detection zone and for performing the walk test. Pull the switch
to the ON position as” “, pull the switch to the OFF position as” “, switch
location and detection range of the corresponding table is as follows:
Light-control Setting
The chosen light response threshold can be infinitely from approx. 10-501ux,
pull the switch to the ON position as “ “, pull the switch to the OFF position
as” “, switch location and light-control of the corresponding table is as
follows:
Stand-by Light Level Setting
Switch to the on is” “, switch to the off is” “; the corresponding file of
switch location and detection distance is as follows:
Stand-by Time Setting
The file of switch location and detection distance as follows: file of switch location and detection distance as follow:
PARAMETER SETTING BY REMOTE CONTROL IN MANUAL OF RC-100.
INSTALLATION
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>