OMNIFILTER BF55 Heavy duty Opaque Filter Housing Installation Guide

OMNIFILTER BF55 Heavy-duty Opaque Filter Housing

Product Information

• Product: Model BF55
• Brand: OMNIFILTER
• Phone: 800.937.6664
• Website:www.omnifilter.com
• Product Description: 20 Heavy-duty Whole-House Water Filter

Operating Specifications

• Flow Rate: Not specified
• PressureRange: Not specified
• Temperature Range: Not specified

Precautions

• Do not use electrical heating tape on this unit.
• Do not use water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
• The filter must be protected against freezing, which can cause cracking of the filter and water leakage.
• The rubber O-ring provides a water-tight seal between the cap and the bottom of the housing. It is important that the O-ring be properly seated in the groove above the threads of the housing or a water leak could occur.
• Because of the product’s limited service life, it is recommended to replace the bottom of all plastic housings every five years for clear and every ten years for opaque.

Prop 65 Warning for California Residents

This product contains chemicals known to the State of California to cause cancer birth defects or other reproductive harm.

Product Usage Instructions

Installation Instructions

1. Assemble all fittings into the cap by hand. Use a wrench to tighten firmly. Do not over-tighten.
2. Measure the length (shown as X on the diagram) across assembled fittings and to pipe threads of each fitting.
3. If using a mounting bracket, be sure to insert fittings or pipe through the bracket before threading into the filter cap.
4. Allow 1-1/2 inches of clearance below the housing to enable filter cartridge changes.

Additional Assistance

If you need further operating, installation, maintenance, parts, or assistance, please call OMNIFILTER Customer Service at 800.937.6664.

Materials Required

• Tubing cutter (preferred) or hacksaw to cut into pipes
• 10″ adjustable wrench to tighten fittings
• Assortment of pipe fittings to connect from existing piping to filter unit
• The type of fittings used will vary with your application and location
• Plumber tape
• Tape measure
• Bucket or pail
• Cartridge
• Pencil

Parts Included

• Housing wrench

Optional Parts Not Included

• BF55MB mounting bracket
• 20” Heavy-duty filter cartridge

OPERATING SPECIFICATIONS

• Flow Rate: 20 gpm
  Pressure Range: 30–90 psi
  Temperature Range: 40°–100°F

Precautions

• Carefully read and follow instructions.
• WARNING Risk of electrical shock. If your water pipes are used to ground your home’s electrical system, install a No. 8 AWG jumper wire (or larger) around the filter. The jumper wire must be connected at both ends by a pressure wire fitting or other connection that satisfies NEC or CEC and local codes. Consult a building inspector or licensed electrician for more information.
• WARNING Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
• WARNING Prop 65 Warning for California Residents: This product contains chemicals known to the State of California to cause cancer or birth defects or other reproductive harm.
• CAUTION Filter must be protected against freezing, which can cause cracking of the filter and water leakage.
• CAUTION The rubber O-ring provides the water-tight seal between the cap and the bottom of the housing. It is important that the O-ring be properly seated in the groove above the threads of the housing or a water leak could occur.
• CAUTION Because of the product’s limited service life and to prevent costly repairs or possible water damage, we strongly recommend that the bottom of all plastic housings be replaced every five years for clear and every ten years for opaque. If the bottom of your housing has been in use for longer than this period, it should be replaced immediately. Date the bottom of any new or replacement housing to indicate the next recommended replacement date
• CAUTION Do not use electrical heating tape on this unit.

NOTES:

• For cold water use only.
• The contaminants or other substances removed or reduced by this water treatment device are not necessarily in your water. Ask your local water municipality for a copy of their water analysis, or have your water tested by a reputable water testing lab.
• Filter cartridge life varies depending on filter type, usage, and water conditions.
• The replacement filter cartridge used with this system has a limited service life. Changes in taste, odor, or flow of the water being filtered indicate that the cartridge should be replaced.
• Use only OMNIFILTER replacement cartridges.
• This installation must comply with all applicable state and local regulations.
• Use only Plumber tape without adhesive backing to seal joints. Do not use pipe compound (pipe dope), sticks, or similar compounds with this unit; they contain petroleum derivatives which will cause crazing and cracking of the plastic in the filter housing.
• Use only soap and water to clean filter housing and components.
• After prolonged periods of non-use, such as a vacation, it is recommended that the system be flushed thoroughly. Let water run for 5–6 minutes before using.
• Do not use a torch near the unit.
• An activated carbon cartridge may contain a small amount of carbon fines (very fine black powder). A new cartridge, after installation, should be flushed with sufficient water to remove the fines before using the water.
• Wear safety glasses during installation.

Installation Instructions

NOTE:

• Please read all instructions, specifications, and precautions before installing and using this filter.

• For installation on standard 1-inch main copper water line.

• Use only plomería tape for fitting housing connections.

• Install filter cartridge in filter housing according to the filter cartridge replacement instructions (below) before proceeding with installation. See Filter Cartridge Selection Guide on page 5 to determine the best cartridge for your filtration needs.
  Install filter after water meter or pressure tank.

• Numbered diagrams correspond with numbered steps.

1. Apply about three wraps of plumber tape in clockwise direction to pipe threads of each fitting.

   • NOTE: If using mounting bracket, be sure to insert fittings or pipe through bracket before threading into filter cap.
   • NOTE: Allow 1-1⁄2-inches clearance below housing to enable filter cartridge changes.

2. Assemble all fittings into cap by hand. Use a wrench to tighten firmly.

   • DO NOT OVER-TIGHTEN.

3. Measure length (shown as X on diagram) across assembled fittings and subtract 1-inch if you are installing on 3/4-inch pipe, or 1-1⁄2-inches if you are installing on 1-inch pipe. Mark the section of pipe to be removed.

4. Turn off the main water supply valve and open a faucet on the lowest level of your home to drain the system. Cut the correct length of pipe. Use a pipe cutter or hacksaw. File or sand the ends of the pipe to make sure they are smooth and square.

   • NOTE: Have a bucket handy to catch any water that may come out
     the pipe.

5. Align filter assembly with ends of pipe, making certain cap opening marked “IN” is facing the incoming water supply. It will be necessary to spread ends of pipe apart to install filter assembly. Using two adjustable wrenches, hold incoming adapter securely with one wrench and tighten nut with second wrench. Repeat procedure for outgoing adapter.

   • WARNING Risk of electrical shock. If your water pipes are used to ground your house’s electrical system, install a No. 8 AWG (8.4mm2) jumper wire (or larger) around the filter (see Figure 6). The jumper wire must be connected at both ends by a pressure wire fitting or other connection that satisfies NEC or CEC and local codes.

6. Unscrew housing from cap and insert cartridge into housing making sure the cartridge is centered over the standpipe in the bottom of the housing.

   • Note: Make sure all packaging materials are removed from the cartridge before inserting into the housing.

7. Locate O-ring and tube of Silicone lubricant included with unit. Open lubricant tube and apply a small amount to O-ring and with your fingers make sure the entire O-ring is coated.

8. Insert O-ring into grove on the top of the housing. Check to make sure there the grove is free of any dirt. Press O-ring into place with your fingers to make sure it is seated in the grove.

9. Reattach the housing to the cap making sure the standpipe in the cap slips into the end of the cartridge and tighten the housing to the cap by hand until it is snug. To prevent damage DO NOT OVER-TIGHTEN the housing to the cap, it just needs to be snug.

   • Note: The housing wrench that is provided is only used for removing the housing when you change the cartridge.

10. Slowly turn on water supply to the filter and depress the red pressure-relief button on cap to release trapped air. Check for leaks. Open the nearest faucet and flush for 10 minutes, wait one hour, then flush again for 10 minutes.

FILTER CARTRIDGE REPLACEMENT

The life of the cartridge depends on the water volume used and the substances in the water. Normally the cartridge should be changed at intervals, see specifications on cartridge for recommended life or capacity. Replace it sooner if the water pressure at the faucet begins to drop noticeably or if you notice changes in the taste, color, or flow of the filtered water.

1. (A) Bypass water to the filter by turning the handle clockwise1/2 turn until it comes to a stop.
   • NOTE: This will shut off all water flow to the housing. Water going to the household is not being filtered at this time. Be sure to fill a bucket of water first so you may clean the housing after it has been removed.
   • (B) Remove the bottom of the housing by unscrewing.
2. Locate and remove the large O-ring (A), wipe clean of lubricant, and set aside. Discard used cartridge (B). Rinse out the bottom of the housing and fill 1/3 full with water. Add 2 tablespoons of bleach and scrub the cap and bottom of the housing with a non-abrasive sponge or cloth. Rinse thoroughly. Lubricate O-ring (C) with clean silicone. Insert the O-ring back into a groove and smooth it into place with a finger.
   • NOTE: This step is important to ensure proper housing seal. Make sure the O- O-O-ring is seated level in the groove.
   • Insert new cartridge (D) over the standpipe at the bottom of the housing.
3. (A) Screw the bottom of the housing onto the cap and hand-tighten until snug. DO NOT OVER-TIGHTEN. Make certain the cap standpipe slips into the cartridge.
4. (B) Slowly turn the handle on the housing 1/2 turn counter-clockwise to allow the filter to fill with water. (C) Depress the red pressure-relief button to release the trapped air. Flush the cartridge for 15 minutes before use. Check for leaks before leaving the installation

TROUBLESHOOTING

Leaks between cap and bottom of filter housing:

1. Turn off water supply and press the red pressure relief button. Remove bottom of housing.
2. Clean O-ring and O-ring groove (located directly beneath threads of housing). Inspect O-ring for defects. Replace if needed. Lubricate O-ring with clean silicone and replace securely into groove. Screw bottom of housing onto cap and hand-tighten until snug. DO NOT OVER-TIGHTEN.
3. Turn on water supply. Depress red pressure relief button to release trapped air. If leaks persist, or if there are other leaks on the system, turn off water supply. Call OMNIFILTER Customer Service at 800.937.6664.

on inlet/outlet connections:

1. Turn off water supply. Depress red pressure relief button to release trapped air. Tighten fittings about 1/2 turn with a wrench.
2. Turn on water supply. If leaks persist, or if there are other leaks on system, turn off water supply. Call OMNIFILTER Customer Service at: 800.937.6664.

OMNIFILTER REPlACEMENT CARTRIdGE SElECTION GuIdE

Cartridge| RS6-20|

TO8-20

Media| Pleated| Radial Flow Carbon
Micron Size (Nominal)| 30| 25
Reduces Sediment| Yes| Yes
Reduces Rust Staining|  |
Reduces Chlorine Taste & Odor|  | Yes

Filter Capacity

| 60,000 gals or 12 months| 100,000 gals or 9 months
Recommended Flow Rate|

20 gpm

|

8 gpm

Well Water Use| Yes| Yes

Nominal: Smaller micron rating equals finer filtration.

REPLACEMENT PARTS

4

|

OW55

| Wrench

For replacement parts, contact your nearest OMNIFILTER retailer or call 800.937.6664.

Limited 5-Year Warranty

OMNIFILTER warrants to the original owner (under normal use) that water Filter Housings are to be free from defects in material and/or workmanship for five (5) years from the date of purchase. Any replacement products furnished will be free from defects in material and/or workmanship for the remainder of the original warranty period. This warranty does not cover:

1. filter cartridges
2. damage due to lightning or other conditions beyond the control of OMNIFILTER
3. defects not reported within the above time period,
4. items manufactured by other companies,
5. problems arising from failure to comply with OMNIFILTER instructions,
6. problems and/or damage arising from acts of nature, abuse, misuse, negligence, or accident by any party other than OMNIFILTER,
7. problems and/or damage resulting in whole or in part from alteration, modification, repair or attempted alteration, modification or repair by any party other than OMNIFILTER,
8. noncompliance with applicable codes/ordinances.

If a defect in workmanship and/or material in a product or part covered by the warranty should arise, OMNIFILTER, at its sole discretion, will repair or replace the defective product or part (OMNIFILTER may consider, in good faith, the customer’s preference).

All claimed defective products must:

1. be authorized for return by OMNIFILTER with an RGA number
2. include proof of the purchase date of the product or part
3. be returned to OMNIFILTER prior to the expiration of the warranty date, at the customer’s expense, shipment pre-paid,
4. be accompanied by a letter detailing the Model Number, Serial Number (if any), and a brief description of the problem.

• TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, OMNIFILTER DISCLAIMS ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WITH REGARD TO THE PRODUCTS, PARTS AND ANY ACCOMPANYING WRITTEN MATERIALS.
• To the maximum extent permitted by applicable law, OMNIFILTER shall not be liable for any damages whatsoever (including, but not limited to, loss of time, inconvenience, expenses, labor or material charges incurred in connection with the removal or replacement of the Water Filter Housing, special, incidental, consequential, or indirect damages for personal injury, loss of business profits, business interruption, loss of business information, or any other pecuniary loss) arising out of the use of or inability to use the defective products or parts, even if OMNIFILTER has been advised of the possibility of such damages.
• OMNIFILTER’s maximum liability under any provision of this Limited Warranty shall be limited to the amount actually paid for the Water Filter Housing.
• NOTE: Because some states do not allow the exclusion or limitation of incidental or consequential damages, the above limitations or exclusions may not apply.
• THIS WARRANTY GRANTS SPECIFIC LEGAL RIGHTS, AND OTHER RIGHTS MAY APPLY. SUCH RIGHTS VARY FROM STATE TO STATE.
• For servicing under this warranty, return any defective part to YOUR DEALER within the five-year period referred to above.
• SEE BELOW THE INDIVIDUAL WARRANTY AS IT PERTAINS TO YOUR OMNIFILTER PRODUCT.
• 5-YEAR: BF55 Omni
• To register your filter: go to www.omnifilter.comwarranty_card.html
• IOWA Residents Only:
• Store or seller’s name
• Address
• City
• State
• Zip
• Telephone
• Seller’s Signature/Firma del vendedor
• Date
• Customer’s Signature
• Date
• 293 Wright St.
• Delavan, WI 53115 Phone: 800.937.6664
• www.omnifilter.com

Documents / Resources

| OMNIFILTER BF55 Heavy duty Opaque Filter Housing [pdf] Installation Guide
BF55 Heavy duty Opaque Filter Housing, BF55, Heavy duty Opaque Filter Housing, duty Opaque Filter Housing, Opaque Filter Housing, Filter Housing, Housing
---|---

References

• Water Filters Online
• Water Softening & Filtration | Pentair Water Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>