SKME Watch User Manual

User Manual of SKMEI Mode #1464

A: Features

• OLED display hour, minute, second, week, date, month, day, temperature function
• 12/24 H Format selectable
• Pedometer
• 7-day step data query function
• Compass
• Alarm and Chime hourly
• Stopwatch(maximum 23:59″59)
• Count Down
• Dual time
• the LED will light on 10 seconds when pressing any key.

B: Synchronous needle function
In the Time mode, press E key to set the needle function, press and hold down E key to move the minute hand quickly
C: Product mode loop

D: Product function mode

E: Product function settings

1. Time and date setting function

• In the Time mode, press A key for 3 seconds to enter the time setting state. At this time,“12H” flashes, press B key “second” starts to flash, then press B key to select the setting  item (flashing) as the following sequence:
• Press C key to increase the selected value, and press D key to decrease the selected value.
•  Press A key to confirm and return to the Time mode.

2. Stopwatch and segment timing function

• The measurement range is 23 hours 59 minutes 59.99 seconds.

• Set stopwatch: In the stopwatch mode, press C key to start running the second, then press C key to stop running, press A key to remove when the running seconds stop.
  Process time
  

• When the stopwatch is running, press B key to switch to other display modes,the stopwatch will continue to measure time.

3.Countdown function

• The countdown timer can be set from 1 second to 24 hours. An alarm sounds when the countdown reaches zero.
• Press C key to start/stop the countdown; when the countdown stops, press A key,the countdown timer will automatically return to the initial setting time.
• When the countdown reaches to zero, the alarm sounds for about 10 seconds or until you stop it by pressing any button. the countdown time is automatically reset to the initial setting time after the alarm stops.
• Timing setting: In the countdown mode, hold down A key for 3 seconds until the “hour” starts to flash, press B key to select the setting item (flashing) as the following sequence:
• Press C key to increasing the selected value, and press D key to decrease the selected value.
• Press A key to confirm and return to the Countdown mode.

4.Alarm function

• In the Alarm mode, press C key to switch the mode as follows:

• In the relative mode, press A key to turn on/off the alarm and Chime Hourly function.

• In the Alarm mode, hold down A key for 3 seconds until the “hour” starts to flash, press B key to select the setting item (flashing) as following：

• Press C key to increasing the selected value, and press D key to decrease the selected value.

• Press A key to confirm and return to the Alarm Mode.
  Remarks：

• In any mode, the alarm will sound for 10 seconds when it reaches the preset time. During the alarm, press any button that can stop ringing.

• The intermittent alarm sounds once every 5 minutes, sounds 7 times in total. You can press any key to interrupt the ringing.

• After turned on the Chime Hourly function, the watch will beep twice at each hour.

5.Dual time function

• In the Dual time mode, hold down A key for 3 seconds until the “hour” starts to flash, press B key to select flashing
• Press C key to increasing the selected value, and press D key to decrease the selected value.
• Press A key to confirm and return to the Dual time mode.

6.Pedometer function

• In Pedometer mode, press C key to“turn on/pause” the function.

• In Pedometer mode, press A key to switch the mode as follows.

• In Pedometer mode,hold down A key for 3 seconds to start setting.

• Metric/Inch: The default is the metric system, press C key to switch to metric or imperial.

• Set weight: The default weight is 50kg (20IN), adjustable range: 20-200kg/44-440Lb;

• Set step distance: the default step distance is 70cm (154LB), adjustable range: 30-200cm/12-79in;

• Press C key to increasing the selected value, and press D key to decrease the selected value.Metric/Imperial has no
  fast-adjusted function.

• Press A key to confirm and return to the Pedometer mode.

7.Step record query function

• In the Step record mode, press C key to query historical data within 7 days, and press A key to view the data for a certain day.

8.Compass function

• In Compass mode, turn the movement to display the compass angle.
• hold down A key for 3 seconds into the Compass calibration mode.
• In Compass calibration mode 1, press C key when the arrow points to the 6 position when OK appears then into Calibration mode 2.
• In Compass calibration mode 2, hold the watch upside down , press C key when the arrow points to the 12 position, when OK appears then the calibration is completed  and back to the Compass mode.
• Magnetic declination correction
• Press C key to increase the selected value, and press D key to decrease the selected value.
• Press A key to confirm and return to the Compass mode.

F: Quality standards

1. Movement size: Ф38.1mm
2. Thickness (with buzzer): 8.10mm
3. Working temperature: 0°C ~ +50 °C
4. Working voltage: 3.0V
5. Battery model and capacity: CR2032 (capacity 220m Ah)
6. Accuracy: ±90 seconds/month
7. Static average current: ≤6.0u A
8. Alarm average current: ≤5.0m A
9. OLED light average current: ≤10m A
10. Battery life (85%): ≥ 18 months (Japan Electric)

(The light is on 5 times a day, 10 seconds for each time, light on 50 seconds in total; sounds for 20 seconds every day.)

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>