LNC A05167 22 Inch 3 Light Polished Gold Instruction Manual
- June 14, 2024
- LNC
Table of Contents
- LNC A05167 22 Inch 3 Light Polished Gold
- Product Information
- Product Usage Instructions
- IMAGE FOR FINISHED PRODUCT
- TOOLS REQUIRED
- PARTS INCLUDED
- ACCESSORIES ENCLOSED
- ASSEMBLY & INSTALLATION INSTRUCTIONS
- Connect ground wires according to the chart below
- ORDERING PARTS
- CLEANING
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
LNC A05167 22 Inch 3 Light Polished Gold
Product Information
Specifications
- Item Number: A05167
- Maximum Wattage: Type A, Max 60W per bulb
- Voltage: 120V
Product Usage Instructions
Safety Precautions
To reduce the risk of fire, electric shock, or personal injury, please follow these safety precautions:
- We suggest installation by a licensed electrician.
- Read the instructions carefully and save them for future reference.
- Before starting any work, always shut off the electricity.
- Ensure that the mounting surface is clean, dry, flat, and strong enough to hold the lamp securely. It should be 1/4 larger than the canopy on all sides.
- Any gaps between the mounting surface and canopy exceeding 3/16 should be corrected.
- Ensure that the ceiling or wall can support the weight of the lamp before installation.
- Keep the lamp away from acidic and alkaline substances to prevent damage to the lamp’s surface.
- When replacing bulbs, turn off or unplug the lamp and wait until it is cool, as bulbs can get hot quickly.
- Use common sense, caution, and care when working with electrical products.
Tools Required
Before starting assembly and installation, please prepare the following tools:
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Assembly & Installation Instructions
- Carefully remove the fixture from the carton and check that all parts and accessories are included.
- Turn off the power before starting the installation.
- Secure the mounting plate (D) to the outlet box using the provided mounting screws (A).
- Connect wires according to the charts provided in the manual.
- Twist wires together with plastic wire connectors (B) until tightly joined.
- Wrap each connector with approved electrical tape.
- Ensure that no wire strands are exposed and carefully tuck all wires into the outlet box.
FAQ
Q: What is the maximum wattage for each bulb?
- A: The maximum wattage per bulb is 60W for Type A bulbs.
Q: Can I install the lamp myself?
- A : We suggest installation by a licensed electrician for safety reasons.
Q: Can I use bulbs with higher wattage?
- A: No, the maximum wattage per bulb should not exceed 60W.
Q: What should I do if there are gaps between the mounting surface and the canopy?
- A : Any gaps exceeding 3/16 should be corrected before installation.
Q: Can I replace bulbs without turning off or unplugging the lamp?
- A : No, it is recommended to turn off or unplug the lamp and wait until it is cool before replacing the bulbs.
Item Number: A05167
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instructions carefully and save them as you may need them at a later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED
(NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture
PARTS INCLUDED
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (3)
- (H) Lampshade (3)
- (I) Socket ring (3)
ACCESSORIES ENCLOSED
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Turn off power
- Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
- Go to the main fuse, or circuit breaker, box in your home.
- Place the main power switch in the “OFF” position.
- Place the wall switch in the “OFF” position.
- Make assembly
- Step A1 » Unscrew knob nuts (F) from back plate (E) and mounting plate (D), then set them aside for later installation.
- Step A2 » Carefully pass the supply wires from the outlet box through the mounting plate (D).
- Secure mounting plate (D) to the outlet box with mounting screws (A).
- Step A3 » Make wire connections Connect wires as shown in the charts below. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the chart below
- Note: When parallel wires (SPT I&SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
- Twist wires together with plastic wire connectors (B) until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
- Step A4 » Align the holes in back plate (E) with the pre-assembled mounting screws, then attach back plate (E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
- NOTE: back plate (E) should be snug against the wall with knob nuts (F).
- If not, remove the back plate (E), and adjust the threaded length of pre-assembled mounting screws on the mounting plate (D):
- Unscrew the pre-assembled hex nuts.
- Screw the pre-assembled mounting screws in or out of the mounting plate (D).
- When the secure length is achieved, tighten the pre-assembled hex nuts and back to Step A4.
Step A5 »
- Remove socket rings (I) from sockets (G).
- Carefully hang lampshades (H) onto sockets (G), and then screw socket rings (I) to sockets (G) to secure them.
- When installing socket rings (I), the orientation of socket rings (I) is that the side of the rolled edge faces upward.
- Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
- Check that everything is installed properly, then you can turn on the light. We hope you enjoy your new lighting!
ORDERING PARTS
- Keep this sheet for future reference in case you need to order replacement parts.
- All parts for this fixture can be ordered from the place of purchase.
- Be sure to use exact wording from illustrations when ordering parts.
CLEANING
- To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap).
- Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>