tmezon MZ-ZS-GQ3 Solar Surveillance Camera Outdoor Battery User Manual

: June 14, 2024
: TMEZON

Table of Contents

Camera Introduction
APP Operation
Charge the battery
Installation Guides
Notes on PIR Motion Sensor
Important Notes on Reducing False Alarms
FAQs
Share device
Read User Manual Online (PDF format)
Download This Manual (PDF format)

tmezon MZ-ZS-GQ3 Solar Surveillance Camera Outdoor Battery

Camera Introduction

Power Button	Press and hold for 5s to power on/ off the camera
Reset Button	Press and hold for 5s until hearing “Boogu” to reset or

restore to factory setting
SD Card slot| Support local SD card storage (up to 12GB)
Charging Indicator| Red means charging , blue means fully charged
Working Status Light| Solid red : Network is abnormal
Slow flickering red : Awaiting WiFi
Fast flickering red : WiFi connecting
Solid blue: WiFi connected successfully, the camera running normally
USB Charge Port| Use 5V2A power adapter to charge this camera

APP Operation

Download APP
The app is Cloud Edge.
Search the name “Cloud Edge” in App Store or Google Play Store, or scan the QR-Code to download the App.|
---|---

Download App ( IOS & android )

WiFi connection
Please insert Micro SD card before power on, otherwise, the SD card will not be detected.
Switch on the camera, you will see the LED indicator flashes red. Start setting up the camera following the in-a pp instructions.

Note:

Please operate the setup near your Wi-Fi router.
Make sure that the WiFi is 2.4Ghz, 5Ghz WiFi is not supported. The mobile phone should be connected to 2.4Ghz WiFi before adding the device.
Make sure the camera is turned on, and its indicator LED is flashing red . If not, press and hold RESET for 5 seconds.
Ensure the Wi-Fi siganal is good, and the Wi-Fi password is correct.

Step 1 : Login app, click”+” or “Add Device” to add the device

Step 2: Select “Battery camera”

Step 3: Make sure that the camera is powered on

Step 4: Reset camera

Step 5: Connect 2.4Ghz WiFi, enter WiFi password (5Ghz WiFi is not supported.
The WiFi password should not have a special symbol)

Step 6: Get QR code and use the camera to Scan QR code

Step 7 : Connect Network

Step 8 : Connection successful

Note: If you need to re-select the WiFi network, please press and hold the “RESET” button to reset the camera, then add the device again.

Charge the battery

Charge the battery with a 5V2A power adapter.

The battery is a built-in battery and cannot be removed.

Charge the battery With solar panel.

For the weatherproof performance, always cover the USB charging port with the rubber plug after finishing charging the battery.
Charging indicator:
Red LED: Charging
Blue LED: Fully charged

Installation Guides

Install the camera 2-3 meters (7-10 ft) above ground. The detection range of the motion sensor would be maximized at such a height.
For effective motion detection, please install the camera angularly.

Note:
If a moving object approaches the PIR sensor vertically, the camera may fail to detect motion.

Notes on PIR Motion Sensor

PIR Sensor Detection Range
The PIR detection range can be customized to meet your specific needs.
You may refer to the following table to set it up in Device Settings via Cloud Edge APP.

Sensitivity	Detection distance (for moving and living objects)
Level 1-3 (Low)	Up to 2-5 meters
Level 4-7 (Middle)	Up to 5-8 meters
Level 8-10 (High)	Up to 8-1 0 meters

Important Notes on Reducing False Alarms

Do not face the camera towards any objects with bright lights, including sunshine, bright lamp lights, etc.
Do not place the camera near any outlets , including the air conditioner vents, humidifier outlets, the hear transfer vents of projectors, etc.
Do not install the camera at places with strong wind.
Do not face the camera towards a mirror.
Keep the camera at least 1 meter away from any wireless devices, including WiFi routers and phones in order to avoid wireless interference.

FAQs

The device prompts offline?|

Check whether the equipment is in the power-on state , and observe whether the working light of the equipment is on normally.
Check whether WiFi network is in good condition and restart the router.
lf the device is located faraway from the router, which results in the inability to obtain a good WiFi signal, it is recommended to move the router to a closer place or ensure the WiFi signal strength is to be over than 85% to improve the WiFi performance of the home.
Delete the camera from your CloudEdge account and add it again after resetting the device. Check whether the device firmware and application program are the latest version.

---|---
Update router or WiFi password?| Delete the camera from your Cloud Edge account.
After resetting the device, use the new WiFi and password to add it again.
Alarm push frequently?|

In the app, lower the sensitivity of the motion detection alarm.
Check whether there are objects that interfere with and trigger the Pl R sensor in the field of view of the device, such as the outdoor unit of the air conditioner, driving cars, passing pedestrians. etc.
The angle of the device can be adjusted appropriately to avoid these easily disturbing objects.
Turn on “Human motion” detection and use humanoid algorithm to filter useless alarms.

Step 1: Click “Setting” on the upper right corner

Step 2 : Click “Device Share”

Step 3: Click “Add”