TMEZON MZ-IP-V1026TW 4-Wire Digital-Analog Hybrid System Instruction Manual

TMEZON MZ-IP-V1026TW 4-Wire Digital-Analog Hybrid System

Description on indoor monitor

other video modes: 1080P-720P-CVBS
26| Semiconductor fingerprint sensing area
27| Port for EXIT Switch
28| Connect to the monitor
29| Connect to the door lock

Wiring diagram

• 110″ Monitor+1 Outdoor doorbell
• 2 7″ monitors +2 Outdoor doorbells
• 1 Master Monitor+5 slave monitors+2 Outdoor doorbells+ 2 CCTV Cameras

Note on wiring connection

Please pay attention to the name marked on the sticker of the machine to avoid a wrong connection. Wiring requirements (The actual effect and the quality of wire rod has the very big relations):

1. 4 core ordinary unshielded and shielded wiring cable;

2. The effective distance from the outdoor camera to the furthest indoor monitor: Transmission <30m (4×0.4mm )2
   Transmission <60m (4×0.65mm )2

3.  If you want to extend the distance to more than 60m, it is best to choose thick copper core cable, shielded wire or 3-core ordinary unshielded wire + 75-3 video cable. Connect the shield terminal to GND.
   Three-wire unshielded cable + SYV75-3 video cable Integrated video surveillance cable with power cord(2×0.5mm +75-3)

4. If a user wants to use CAT5 or CAT6 network cable. the effective distance from the outdoor camera to the furthest indoor monitor will be limited.
   For the unshielded network cable, the distance will be up to 20m.
   For the shielded network cable, the distance will be up to 40m.
   So CAT5 or CAT6 network cable is not recommended.
   CAT5 or CAT6 network cable consists of 4 pairs of twisted pairs(8 wires), here one pair of twisted pair will be used as one cable.
   Green &White+Green, Brown&White+Brown, Orange&White+Orange, Blue&White+Blue.

Specification for indoor monitor

Install the indoor monitor

Specification for doorbell

 |
 | Sensor area| 1/2.9″
 | Resolution| 1920 X1080
 | Standard| PAL/NTSC
 | View angle| 150
 | Standby current| Max60mA
 | Work current| Max200mA
 | Power supply| DC9V-DC15V
 | Work temperature| -40~+50 C
 | Password capacity| Max 200PCS
 | RFID card capacity| Max 200PCS
 | Fingerprint capacity| Max 200PCS

Install the outdoor doorbell

1. Please be far from the devices with intense radiation: TV, DVR, etc.
2. Do not disassemble privately to avoid the electric shock.
3. Do not drop, shake or knock the device, otherwise will damage the elements. 4:Choose the best position to install, the horizontal view is 150cm.
4. Please power down before installation.
5. Keep at a distance of more than 30cm with AC power to avoid interference. 7:Away from the water, magnetic field and chemicals.

Wiring diagram for outdoor doorbell

Model: MZ-VDP-NE202

a Setting button: Add card mode or Reset mode

1. Mode to add RFID card: In standby mode, short press the setting button, enter the mode to add RFID card, swipe RFID card in the card swiping area, you can add a card, you can Repeat the RFID card to add more RFID cards, and then press the set button to exit the mode to add RFID card.

2. Reset mode: In standby mode, press and hold the setting button for
   3 seconds to enter reset mode, then press the setting button three times, you will hear a sound, all card numbers will be deleted, and it will return to standby mode.
   Note:
   Different modes for the doorlock’s connection
   A mode: For the doorlock which is less than 12V1A
   B mode:

3. For the doorlock which is more than 12V1A

4. If the cable exceeds 20 meters from the indoor monitor to the doorlock, connect them as B mode only

Model: MZ-VDP-NA262F

Operation mode for the outdoor doorbell

Model: MZ-VDP-NA262F

Menu operation

Menu styles

1. Win10 style
2.  Android-style
3. Standard style
   Three styles of interface can be set through the menu. No need to restart the monitor

Setting

System

1. Please format the SD card with the device and copy the files to the corresponding folder.
2. Restore factory settings: All parameters are restored to factory mode. Note that TuyaSmart’s device must be deleted together before it can be used again, otherwise it cannot be added and used by other accounts.
3. The Device ID is an important configuration of the equipment in the system.
   It must be configured correctly, Otherwise it will not work properly. If the current device
   is connected to the Outdoor unit1, Device ID must be set to 1, and the other Slave monitors must be set 2/3/4/5/6, then work normally.

Time

1. (Screen off): Monitor will be off with no operation within 10s
2. (Clock): Time will be displayed on the screen at standby mode

Digital Frame

1. The picture file must be copied to the Digital Frame folder, the picture resolution
   must not be greater than: 2526×1576, the format is JPEG.

2. Long press the file to pop up the submenu, select “Delete” or “Delete All”, and click the file to enter the playback interface.

Devices

1. If the channel is closed, it will be skipped when monitoring the polling screen. This
   channel and APP will not display this channel. Please set it carefully.

2. When Motion Detection Push APP is closed, the phone will not receive any push information.

Ring

1. The ringtone of each channel can be set to three time periods, and different ringtone types and volumes can be set, but it should be noted that there can be no gaps and overlaps between the three-time periods, otherwise the system will play the default parameters.
2. Please note that the volume setting of the Door bell cannot be greater than the volume of the indoor monitor.

Recording

1. Click the file to play directly, long-press the file to enter the delete/read operation.

Live view on the monitor

Connect network for the indoor monitor

Connect the device to the app via AP mode
Configure the AP mode in menu (Settings>Network), press the “Return” button to restart the device.

You will view the WIFI hotspot and password on the following interface after the restart.

Add device to TuyaSmart app

The app for the device is TuyaSmart.
Please download the TuyaSmart app from Google Play Store or App Store.

Note:
The device only works with 2.4Ghz WiFi, not 5Ghz.

1. Open TuyaSmart and Add Device
2. Video Surveillance>Smart Doorbell
3. Select AP mode
4. Select 2.4Ghz WiFi network
5. Switch to smartphone’s setting to connect the device’s hotspot
6. The name of the WIFI hotspot is the same as the interface, and the password is 12345678
7. Return to app to add the device
8. Added successfully

Share device

• Steps: Settings>>Share Device>>Tap on “Add Sharing”>>Type in account>>Confirm Sharing.
  Note: Other users should create an account for the TuyaSmart app before sharing.

Function description for the app

1. If the device has been successfully connected to the user’s smartphone, the user needs to delete the device on the APP before adding it to another smartphone. (Note: The device should be deleted when the network is good, otherwise it’s only deleted on the APP, but not on the server). After deleting, go back to the APP to check and confirm.
2. If a new user needs to add the device again after the machine restores to the factory settings, the current user needs to delete the device before re-adding. Otherwise, it is impossible to add the device to the app as new device.

References

• video intercom doorbell system_wireless security system manufacturer_wireless home security system_secure closed circuit television camera-TMEZON

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>