tmezon MZ-IP-V739B NW 4 Wire IP Video Door Phone Instruction Manual
- June 14, 2024
- TMEZON
Table of Contents
- Description Of The Indoor Monitor
- Note On Wiring Connection
- Install The Indoor Monitor
- Specification
- Description On Indoor Monitol
- Instruction for outdoor doorbell
- Installation for outdoor doorbell
- Connect the device to mobile phone
- Sign up an account
- Set up IP Indoor Monitor
- Wireless network
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Operation instruction
4-Wire IP Video Door Phone
User Manual
Description Of The Indoor Monitor
Accessories
Wiring Diagram
Can connect up to two cctv cameras, the definition for the cctv cameras should
be as below: AHD(720P/1080P) / TVI / CVI / CVBS
Can connect up to two doorbells, the definition for the doorbells should be as
below: AHD(720P/1080P) / TVI / CVI / CVBS.
Connect up to two extension indoor monitors
Note:
- The CCTV camera must use an external power supply.
- AHD/TVI/CVI/CVBS definition cameras can be mixed connected.
- When mixed-resolution cameras are connected to the main monitor, suggest that the connected slave monitor is AHD(720P or 1080P). If the CVBS slave monitor is connected, you can only view the image of the CVBS camera on the slave.
- All the cameras must be connected to the monitor before powering on the monitor.
Note On Wiring Connection
The power supplies for electric lock, CCTV cameras and extension cables are
not included in the package, user can purchase according to actual
requirement.
In the standard delivery the system supports locks with Normally Open (N.O.)
door unlocking method. It means that in the normal state the dry contact is
opened so the lock is kept under constant closed state. f the unlocking push-
button is pressed and the dry contact is changed to closed, then the lock is
released.
Please check that the socket of power supply (silk printing J01) is correct if
you connect the external switching power supply, otherwise it will damage the
device. Please first pull out the DC power plug before installation of
device(Shown as below).
Wiring connection according to the following to avoid interference:
A. Wiring connection between outdoor bell and IP indoor monitor. B. Wiring connection between indoor monitors.
Please note the silk printing marked on PCB in order to avoid incorrect
connecting.
The wiring connection requirement (The actual effect and the quality of wire
rod has the very big relations):
-
4-Core ordinary unshielded and shielded wiring cable;
-
Effective distance from the outdoor camera to furthest indoor monitor:
Transmission ≤30m (4×0.4mm²)
Transmission ≤50m (4×0.65mm²)
Unshielded wiring cable: -
If you want to extend the distance over 50m, you’d better to choose a thick copper core cable, or a shielded wiring cable(75-4+2*0.5mm’shielded coaxial wiring cable), or a 3-core ordinary unshielded wire + a 75-3 video wire.
*75-4+20.5mm’shielded coaxial wiring cable:
Connect the shielded wiring cable to GND, connect the coaxial wiring cable to Video, connect the other two wiring cable to Audio and VCC; 3. core unshielded wiring cable+75-3 video wiring cable:**
Connect the shield of the 75-3 video wiring cable with the GND of the 3-core unshielded wiring cable. -
If user wants to use CAT5 or CAT6 network cable, effective distance from the outdoor camera to the furthest indoor monitor will be limited. For unshielded network cable, the distance will be up to 20m. For shielded network cable, the distance will be up to 40m. So CAT5 or CAT6 network cable is not recommended.
CATS5 or CAT6 network cable consists of 4 pairs of twisted pairs(8 wires),
here one pair of twisted pair will be used as one cable.
Green&White+Green, Brown&White+Brown, Orange&White+Orange, Blue&White +Blue.
Unshielded network cable:
Shielded network cable:
Connect the shield of the network cable with the GND.
When the distance from the outdoor doorbell to the indoor monitor is too far, maybe over 50m or 60m, please make sure that the input voltage to the outdoor doorbell must reach 11,7V.
Install The Indoor Monitor
Specification
Display | 7 inch TFT LCD |
---|---|
Resolution | 1024 (H) X600 (V) |
Video system | PAL/NTSC compatible |
Intercom mode | Semi-Duplex communication |
Conversation duration | 120 seconds |
Standby status | 420mA max. |
Working status | 900mA max. |
Additional memory | Support additional TF card (256GB max.) |
Power supply | External switching power supply DC 12V |
Operation temp. | -10∼+60°C |
Installation | Surface mount |
Dimensions | 23614214mm |
Description On Indoor Monitol
NO. | Name | Descriptions |
---|---|---|
1 | Power LED, the power indicator of the indoor monitor. | |
2 | 1 | The door 1 state Iights, to door 1 working when the LED is on. |
3 | 2 | The door 2 state Iights, to door 2 working when the LED is on. |
4 | TFT dispIay | View visitor’s image or menu interface dispIayed on the TFT |
screen.
5| Microphone| Transmit the voice to outdoor camera.
6| | 1. Transfer caII, during conversation mode press this button to transfer
calls to another indoor monitor.
2. InternaI communication, in standby mode, press the button to activate
internal communication with the other indoor monitor.
7| | 1. Monitor, watch the door and camera images.
2. In fiIe Iist interface, press this button to page up.
8| | 1. TaIk, press this button to activate conversation mode.
2. In fiIe Iist interface, press this button to page down.
9| | UnIock, reIease the door Iock.
10| | 1. Hang up, during conversation press this button to end conversation
mode.
2. Return, on menu interface press this button to return to the previous.
11| | 1. In standby mode, press the button “ ” once to access the main menu.
2. On the menu interface, scroII the button “ ” up or down to move the
cursor.
3. On menu settings, after choosing sub-menu setting, press the button “ ” to
enter sub-menu interface .
4. When setup menu, press this button to enter edit mode, scroII this button
“ ” up or down to modify parameters, then press this button to confirm.
12| Speaker| Sound from outdoor camera.
13| TF card sIot| Insert a TF card to store video records, audio records and
photographs, supports up to 256GB. AII the recordings and photographs are be
stored in the TF card of the monitor. If the TF card capacity is Iess than
64GB, the fiIe system format of the TF card must be Fat32. If the TF capacity
is greater than or equaI to 64GB, the fiIe system format must be exFat. And it
is recommended to use a TF card with a writing speed greater than CIass 10 on
the device.
Note:
The back-light of each button will be on when user presses any button or some
visitor calls on the outdoor bell. If the indoor monitor is in standby mode,
all button’s back-lights will be off in 10 seconds.
Set System Parameters On Indoor Monitor Outdoor bell and Camera monitoring System setting
Door setting Camera setting
Network setting Senior setting Information Photo frame Playback Screen saver display
Instruction for outdoor doorbell
Accessories
Specification for outdoor doorbell
No. | Descriptions |
---|---|
1. Weather shield | Affix and protect outdoor camera from rain/snow |
2. IR LEDS | Provides illumination with IR LEDs for better visibility. |
3. Camera | Capture image to transmit to display |
4. Speaker | Sound from indoor monitor |
5. Call button | Call indoor monitor for intercommunication |
6. Microphone | Transmit voice to indoor monitor |
7. Screw slot | Slots for installation screws |
8. System port | Connect to the indoor monitor. |
9. Door lock port | Connect to the door lock. |
Camera | 1/3 inch CMOS camera |
---|---|
View angIe | 115o(H.) |
Definition | 1080P(19201080)/720P(1280720)/CVBS |
LEDs for night | IR LEDs(120 o) |
Day/Night | IR-CUT |
Power consumption | 300mA max. |
Power suppIier | SuppIied from indoor monitor |
Operation temp. | -20oC~+60oC |
InstaIIation | Surface mount/AngIe mount |
Installation for outdoor doorbell
You have two options to
install outdoor doorbell: Angle mount and Surface mount Note on doorlock’s connection
The electric locks are usually divided into NC lock and NO lock, their
wiring is different, the NC lock need to work with the additional power supply
control.
Note:
- The doorbeII or the monitor wiII not provide the power to door
- The doorbeII can support door Iocks within
- Door Iock’s power suppIy depends on its door Iock, if the door Iock is 12V, the corresponding power suppIy is 12V,
- Make sure the input voItage from the monitor to the outdoor doorbeII must reach 7V when unIocking.
NO Lock: AIways cIosed when power or power off, onIy open when press
unIock.
NC Lock: AIways open when power off. CIosed when power and open after
press unIock.
Method 1: NO Lock connection without power supply control (NO lock only) Method 2: NO & NC Lock connection with power supply control
Connect the device to mobile phone
Download Tuya Smart app
DownIoad Tuya Smart appIication from APP Store or Google Play Store
WIFI setting
Note:
- Router Band–This IP indoor monitor will only connect to the 2.4GHZ
- Router b/g/n –This IP indoor monitor works on 802(b/g/n)
Sign up an account
Select registration
region.
Email is your avaiIabIe emaiI account.
Password requires at least 6~20 characters with a mix of Ietters and
numbers.
Set up IP Indoor Monitor
Wired network Step 1. Connect your
smart-phone to the WiFi router which you want the IP indoor monitor to be
connected to.
Step 2. Connect the IP indoor monitor to the same WiFi router.
Note: Please make sure the WiFi router and your smart-phone are both
connected to the Internet.
Step 3. Set the “net pairing mode” of the monitor to “Cable”. Enter the
“Setting-> Network setting” menu interface and change the “Net pairing Mode”
to “Cable”. After choosing “CabIe” and press “ ”, the foIIowing window wiII
pop up, seIect “Ok” (the seIected option box is red), and then press “ ” to
confirm, the monitor will auto-reboot. After the monitor restarts, it wiII
enters the cabIe net paring mode, and the monitor wiII obtain an IP
address. Step 4. Login the Tuya
Smart app, add a new IP monitor. Click “Add Device”->“Auto Scan”-> choose
available device found to add.
Wireless network
Note:
- Please note that the monitor only works under 2.4G WIFI, not support 5G
- Bring the monitor and the WIFI router within 49 feet(about 15 meters).
User can configure the monitor through AP mode or EZ mode.
A. Add a device by EZ Mode.
Step 1. Make the monitor into EZ mode;
Note:
The default net paring mode of the monitor is “EZ Mode”.
Enter the “Setting->Network setting” menu interface and ensure the “Net
pairing Mode” to “EZ Mode”.
https://youtu.be/-ZkDr9hjPVM
Scan QR code for tutorial video of app connection
Step 2. Login the Tuya Smart app, add a new IP monitor.
B. Add a device by AP mode.
Step 1. Make the monitor into AP mode by manual.
Enter the “Setting->Network setting” menu interface and change the “Net
pairing Mode” to “AP Mode”. After selecting “AP Mode”, and press the following
window will pop up, select “Ok’(the selected option box is red), and then
press “ ” to confirm, the monitor will auto-reboot. After the monitor
restarts, it will enter the AP net pairing mode, the WiFi hotspot of the
monitor and the password of the hotspot will be displayed on the menu.
Note: The Wifi hotspot of the monitor is shown as “SmartLife-xxxx”, and
the password of the hotspot is “12345678”.
Step 2. Login the Tuya Smart app, add a new IP monitor.
Icons on live view
Share your device
Steps : Settings>>Share Device>>Tap on “Add Sharing”>>Type in
account>>Confirm Sharing.
Note:
- When sharing the device to another account, the registration area of the shared account must be the same as yours.
- If a permanent resident in your home has an account, we recommend that you go to “Home Management” interface to set the account as a famiIy member and share aII your famiIy devices and “Tap-To-Run” Scene with the famiIy member.
Technical support: support@tmezon.com
Official Website: http://www.tmezon.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>