PROGRESS LIGHTING P300485-191 Lexie Collection 2-Light Brushed Gold Contemporary Vanity Light Instruction Manual

: May 15, 2024
: PROGRESS LIGHTING

Table of Contents

PROGRESS LIGHTING P300485-191 Lexie Collection 2-Light Brushed Gold
Models
PACKAGE CONTENTS
HARDWARE CONTENTS
Safety Information
Preparation
Care and Maintenance
Assembly Instructions
WARRANTY AND EXCLUSIVE REMEDY
Read User Manual Online (PDF format)
Download This Manual (PDF format)

PROGRESS LIGHTING P300485-191 Lexie Collection 2-Light Brushed Gold

Contemporary Vanity Light

Models

PACKAGE CONTENTS

HARDWARE CONTENTS

HARDWARE CONTENTS (not actual size)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

CAUTION: Read instructions carefully and turn the electricity off at the main circuit breaker panel before beginning installation.
CAUTION: Risk of fire. Min. 90° C supply conductors. Consult a qualified electrician to ensure the correct branch circuit conductor.
WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.
CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

Preparation

Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
Estimated assembly time: 30 minutes.
Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off the main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

Loosely thread the screws (AA) and the hex nuts (DD) onto the round mounting plate (CC). You now need to adjust the screw length according to the fixture canopy depth.
Attach this assembly to the outlet box using the mounting screws supplied with the outlet box (not provided). Tighten securely.
- Lift the fixture to the mounting surface and pass the screws (AA) through the two mounting holes in the fixture canopy. While holding the fixture with one hand, thread the screws (AA) in or out of the round mounting plate (CC) until 3/16″ of threads are showing. That should be enough to mount the fixture as instructed in step 4.
- Next, take the fixture down go back, and tighten the hex nuts (DD) up against the round mounting plate (CC). You now should have the correct length of threads for mounting the fixture.
Strip 3/8″ of insulation from the electrical wire ends. Using wire nuts (BB), connect the WHITE fixture wire to the BLACK fixture WHITE wire supply to the wire from BLACK the supply outlet wire box; from connect the outlet the box.
Connect the fixture ground wire and supply ground wire on the using a wire nut or by Push fastening all of the wire ground connections round carefully into mounting the plate. outlet box.
Slide the mounting holes in the fixture (A) over the screws (AA) and mount using the surface. cylinder nuts (EE), tighten the fixture against the mounting surface.
Attach the glass shades (B) to the fixture (A) and use the cast socket ring (C) to secure it modestly tight.
Thread the lamps (not included) into the fixture sockets. Use a 100-watt MAX incandescent medium base lamp, SBCFL, or SBLED.

WARRANTY AND EXCLUSIVE REMEDY

Progress products, when properly installed and under normal conditions of use, are warranted to our customers only to be free from defects in material and workmanship at the time of shipment. All warranty claims must be asserted within one year from the date of purchase of the subject items; thereafter, warranty claims will not be honored. The customer’s sole remedy for a warranty claim or otherwise shall be limited to repair or replacement of the subject product if it is shown to have been defective in material or workmanship at the time of shipment. Progress’s sole and maximum liability for a defective product shall never exceed the cost of the subject product.

EXCEPT FOR SUCH A WARRANTY AND EXCLUSIVE REMEDY AS STATED (AND THE EXPRESS WARRANTY OF TITLE, WE DISCLAIM ALL OTHER WARRANTIES, WHETHER EXPRESS OR IMPLIED AND SPECIFICALLY DISCLAIM THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL WE BE LIABLE TO THE CUSTOMER IN WARRANTY, CONTRACT, NEGLIGENCE, STRICT LIABILITY, OR OTHERWISE, FOR ANY DAMAGES, WHETHER INCIDENTAL OR CONSEQUENTIAL, WHICH ARE ALLEGED TO BE CAUSED BY ONE OR MORE OF OUR PRODUCTS, BEYOND THE COST TO THE CUSTOMER OF THE SUBJECT PRODUCT OR PRODUCTS.

Therefore, the customer’s sole and exclusive remedy against us for breach of the warranty, breach of contract negligence strict liability, or otherwise shall be limited to repair or replacement of the subject product at our option (excluding installation and removal charges which shall not be our liability) or, if we choose, refund of the purchase price. In no case does our warranty and exclusive remedy extend to anybody other than our customers? Our customers are not authorized to extend warranties or remedies on our behalf to anyone. Such unauthorized extensions of warranties or remedies by the customer shall remain the customer’s responsibility. The customer is responsible for determining the suitability of our products for the customer’s use or resale, or for incorporating them into objects or for applications that the customer designs, assembles, constructs, or manufactures.

We can assist you with questions regarding product information, assembly, or missing parts