LAI MI TECHNOLOGY RC01RF 2.4GHz RF 4 Zone Remote Control Instruction Manual
- June 13, 2024
- LAI MI TECHNOLOGY
Table of Contents
Manual Instruction
2.4GHz RF 4-Zone Remote Control
Model Number: RCO1RF/RCO1RFB/RCO2RF/RCO2RFB/RCO3RF/RCO3RFB
Features
This product adopt world-wide used 2.4GHz frequency, GFSK control method, with the features of low power consumption, long distance transmitting, strong anti-interference and fast communication rate. It can control our 2.4GHz RF smart lights and controllers with color changing, color Temperature adjust, saturation and brightness changing.
Product Size
Button Instruction
- RCO1RF/RCO1RFB: 4-Zone Dimming Remote Control
| Press the button
to turn ON all linked devices.
---|---
| Press the button to tur OFF all linked devices.
| Touch the slider to dim the brightness from 1%-100%.
| Under dynamice mode, press the button to switch to static light.
| Press the button to switch the dynamic modes repeatedy.
| Press the button to dim the brightness up.
| Press the button to dim the brightness down.
| Press the button to get the 30% brightness.
| Press the button o get the 60% brightness.
| Press the button to get the 100% brightness.
| Lower the dynamic mode speed.
| Accelerate the dynamic mode speed. - RCO2RF/RCO2RFB: 4-Zone DIM&CCT Remote Control
| Press the button to turn ON all linked devices.
---|---
| Press the button to tur OFF all linked devices.
| Touch the slider to dim the brightness from 1%-100%.
| Under dynamice mode, press the button to switch to static light.
| Press the button to switch the dynamic modes repeatedy.
| Press the button to dim the brightness up.
| Press the button to dim the brightness down.
| Press the button to get the 30% brightness.
| Press the button o get the 60% brightness.
| Press the button to get the 100% brightness.
| Lower the dynamic mode speed.
| Accelerate the dynamic mode speed.
3. RCO3RF/RCO3RFB: 4-Zone RGB&RGBW&RGBCCT Remote Control
| Press the button to tum ON all linked devices.
---|---
| Press the button to tum OFF all linked devices.
| Touch the color ring to change the colors.
| Short press the button to switch the pure colors from orange, yellow, green,
cyan, blue, purple and red repeatediy.
Long press the button to switch the pure colors from orange, yellow, green,
cyan, Blue,purplo and rod gradally
| Press the button to get the white light.
| Under white light mode, press the button to change the white light to cold
white.
Under color ight mode, press the bution to reduce the saturation
| Under white light mode, press the button to change the white light to warm
white.
Under color ight mode, press the button to add the saturation.
| Press the button to switch the dynamic modes repeatecly.
| Press the button to dim the brightness up.
| Press the button to dim the brightness down,
| Lower the dynamic mode speed.
| Accelerate the dynamic mode speed
Linking and Unlinking Instruction
Remark: The light can be working after linking with the remote.
Linking Code Instructions
** Linking failed
it light is not biinking slowly, Please follow above steps again.
(Note:** Light that have linked can’t link again)
Unlinking Code Instructions
** Unlinking
failed if light is not biinking quickly, Please follow above steps again.
(Note:** Light haven’ linked that don’t need to unlink)
Group Control
You can add an endless numbers of lights to a zone on the 4 channel remote by
linking the lights to different zones. This way you are completely flexible in
creating different group combinations.
Below you can see some grouping examples.
Remark:
-
The user can re-programme freely as needed. One remote can conirol countless lamps or controllers, but one lamp or controller can only be controlled by five.
remotes (Max). -
Please check the battery installation and controller (totally discharge the power), when you programme after switching off and switching on.
Attention
- This remote only control our 2.4GHz RF products; cannot control other products not made by us.
- In the using of the remote, if the indicated lamp blinking quickly, Please change the battery in time. Please don’ use poor quality battery 10 avoid the leaking of batiery liquid to damage the remote.
- This 2.4GHz remote is precise electronic product; don’t use it in humid, high temperature, dust and high voliage environment; Saving it at indoor, dry and no static electricity environment.
- Please don’t use the remote on the wide-range mefal or strong electromagnetic wave area, otherwise, it wil badly affect the controling distance.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
The devices has been evaluated to meet general RF exposure requirement, the
device can be used in portable exposure condition without restriction