GE 45174 Personal Security Window/Door Alarm User Manual
- June 14, 2024
- GE
Table of Contents
GE 45174 Personal Security Window/Door Alarm
Alarm
Activating batteries
Before attempting to use the window/door alarm, activate the batteries
installed. Slide open the battery door and locate the battery isolation tape.
Hold the batteries in place while pulling out the battery isolation tape. Once
the isolator tape
is removed, and the alarm is active.
Low battery indicator
The alarm has a low battery indicator light. Push the “battery test” button inside the battery compartment. If the green light illuminates when the button is pressed, the batteries are still good. If the light fails to illuminate, replace all batteries.
Batteries
Installing batteries
The alarm requires four LR44 (or 357) button batteries (included). The average
battery life for typical usage is up to one year.
- Remove the screw securing the battery compartment cover.
- Slide the cover of the battery compartment on the front of the main unit.
- Insert four LR44 button batteries noting polarity.
- Replace the battery compartment cover.
Installation
NOTE
The magnet must be placed on the right side of the alarm. The arrows on the
alarm and the magnet must align. Locate a position on the window or door to be
protected that allows easy access to the OFF/ CHIME/ALARM switch. Make sure
the switch is OFF and the mounting surface is clean and dry. For best results,
clean the mounting surface with a mixture of 50% isopropyl alcohol and 50%
water.
Installation Cont
- Peel the protective covering from one side of the double-sided tape and then apply it to the back of the alarm.
- Remove the protective covering from the back side of the double-sided tape and lightly mount the alarm or the magnet on the part of the entry that opens (i.e. the window or door itself).
- Window and door preferred mounting method
- Mount the other piece of the unit on the stationary part of the entryway (i.e. the window or door frame).
- Ensure when the door or the window is closed, the gap between the two pieces of the alarm unit is less than 1/2in.
- Once correct placement is established, press to secure double-sided tape.
Alarm Mode
Operation
- To arm the unit, locate the chime/OFF/alarm switch on the side. Slide the switch to the desired position.
- When in the alarm position, if the protected window or door is opened to separate the alarm and magnet by more than 1/2in., the alarm siren sounds continuous until disarmed or the door or window is closed and the gap is less than 1/2in. When in the chime position, if the door or window is opened, the chime sounds. It chimes once again when the door or window is closed and reopened.
- To disarm the unit, toggle the switch to the OFF position. Make sure the door or window is closed before arming.
NOTE : To test, cover the alarm with a cloth to reduce the risk of hearing damage. To clean the unit housing, use a soft cloth slightly dampened with water and wipe dry. Do not use chemical agents as this may damage and discolor
the unit.
WARNING
Limitations of Alarm Products This product should be tested periodically to
make sure it is working properly. The product, if used properly, may reduce
the risk of burglary, robbery, or other adverse events. However, Jasco is not
an insurer, this product is neither insurance nor a guarantee that such an
event will be prevented, and users should protect themselves with proper
insurance. Jasco makes no representation that this product cannot be
compromised or circumvented, that it will provide an adequate warning, or that
it will prevent any personal injuries, property damage, or other losses. Like
any alarm product, including expensive commercial systems, it may be bypassed,
it is subject to compromise, and it may fail to warn for a variety of reasons,
including, but not limited to.
Warnings Cont
improper installation or positioning; improper maintenance; tampering;
dead or improperly installed batteries; sensing limitations; component
failures; receivers; for infrared products, intrusions may be outside of a
product’s designed range and certain environmental conditions may impact
performance and audible alarm signals may be outside of hearing range, muted
by doors, walls, and floors, unheard by deep sleepers or the hearing-impaired,
or overwhelmed by other sounds
WARNING
RISK OF PERSONAL INJURY
- PROLONGED EXPOSURE TO ALARM SIREN
- MAY CAUSE PERMANENT HEARING LOSS BATTERY WARNING
- REMOVE BATTERIES BEFORE STORING THE ALARM FOR EXTENDED PERIODS
- BATTERIES MAY LEAK HARMFUL LIQUIDS OR IGNITABLE MATERIALS OR EXPLODE E CAUSING INJURY AND PRODUCT DAMAGE
- DO NOT MIX OLD AND NEW OR OTHER S BATTERY TYPE
- REPLACE ALL BATTERIES AT THE SAME TIME
- REPLACE FULLY DISCHARGED BATTERIES IMMEDIATELY
For indoor use only. Do not use in wet locations
MADE IN CHINA
GE is a trademark of General Electric Company and is under license by Jasco
Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product has a 90-day limited warranty.
Visit www.byjasco.com for warranty details.
Questions?
Contact our U.S.-based Consumer Care at
1-800-654-8483, M-F, 7 AM-8 PM Central
Time.
For product patent information, visit
www.byjasco.com/patents.
Thank you for your purchase!
Instructions made easy Read the instructions or watch the easy-to-follow
video. Scan code or visit byjasco.com/56789.
Register your product
Receive exclusive deals and register your product. Scan code or visit
byjasco.com/deals.
Discover dependable security lighting, alarms, and controls at
www.byjasco.com.
Like our product?
Leave a review on retailer your favorite
website or amazon.com.
Having problems?
Let us know how we can
1-800-654-8483, help. Call
M-F, 7 AM-8 PM Central Time.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>